Klimax DSM /3 (2020 Variant)

From LinnDocs
Revision as of 09:15, 20 August 2021 by Yoda (talk | contribs)
Jump to: navigation, search

<< Klimax DSM/2 (2016-2018 Variant) Klimax DSM/0 (Original Variant) >>

 

Linn Klimax DSM

Organik Logo Black 400px.png

Digital music player

Klimax DSM 2021 800px.jpg
Product Name:

KLIMAX DSM/3

Date of Introduction: March 2021



Type: Digital music player with Organik

Variants:
• Klimax DSM AV with full capabilities (EXAKT + HDMI)
• Klimax DSM Music with no HDMI capabilities
• Klimax DSM Hub with only Exakt audio outputs


Setup.png

Get Started
Product informationUnpackingWiringConfiguration....

Kazoo Finger Ctrl.png

Using the Linn Klimax DSM

Control using dial PC/Tablet control IR remote control
Bluetooth-icon.pngBluetooth speakers (Alexa, Google etc)USB connection.pngUSB stream
Roon.pngRoonSpotify-icon-22.pngSpotify ConnectCTRL4.pngControl4 / CrestronIcon.pngCrestron

Features.png

Features:
Surround Sound OrganikDynamik Power SupplyDSD PlaybackEXAKT HDMI-2....

Info2icon.png

FAQ's
Common FAQ'sKlimax FAQTech Specs...







Full Table of Contents / Index      Click to Show / Hide.....

Contents


Product info

Product Name:

KLIMAX DSM/3

Date of Introduction: March 2021



Type: Digital music player with Organik



Hardware Upgrades

UTOPIK Power Supply upgrade: Improved power supply
Note: It should be noted that this upgrade information may at times be out of date and should not be used as a current list of what upgrades are available.

Initial Configuration

Considerations before installation, make sure that you have
  • A mains power socket
Stable mains supply
100-120V rms 50~60Hz,
220-240V rms 50~60Hz
  • An Ethernet/LAN connection to your broadband Router. (You may need to connect it to a wired network connection to allow setup and configuration. Then you can use the Wifi capabilities of your network to control and stream music to the Klimax DSM/3)
  • The HDMI connection from you TV is not too long and is the correct specification cables. HDMI Premium certification.pngLinn recommend using Premium High Speed Certifiied HDMI cables for an optimal experience.
  • The product has adequate ventilation for operation.
  • Positioning positioning



Hardware Upgrades


Note: It should be noted that this upgrade information may at times be out of date and should not be used as a current list of what upgrades are available

Unpacking

  1. Remove product from packaging and place on a flat surface
  2. Please retain all packaging for future transport of Klimax DSM
  3. Check you have all of the accessories.


Top Of Page Index

Wiring

BACKPANEL

Klimax DSM (AV variant)

KDSM Black Rear Panel AV 700px.png
View Klimax DSM (AV) detail - 1,2,3,4.......
Information of what each connector is and a basic specification of these connectors

Click for more....
  1. MAINS INPUT - To connect to the mains electricity supply.
  2. ETHERNET - To connect to a network (100Base-T / 1000Base-T)
  3. USB-A socket: for Service Use only This socket does not accept USB sticks / USB-Drives
  4. FIBRE ETHERNET - SFP module socket to connect to a fibre network
  5. FALLBACK - To put the device into Fallback mode (used when reprogramming)
  6. USB-B socket - To connect to a PC/MAC for Class 2.0 PCM Asynchronous USB Audio playback6
  7. OPTICAL DIGITAL INPUT (TOSLINK)5 - To connect sources with TOSLINK (optical) digital outputs.
  8. DIGITAL INPUT/OUTPUT (SPDIF)5 - To connect sources with SPDIF(BNC) digital outputs or use as an SPDIF digital output.
  9. DIGITAL INPUT (SPDIF)5 - To connect sources with SPDIF(BNC) digital outputs.
  10. EXAKT LINK - To connect to Exakt compatible devices (Exaktbox, Exakt Speakers, Urika II etc)
  11. ANALOGUE INPUTS (RCA-Line level)1 & 2 - To connect sources with RCA analogue outputs.
  12. BALANCED INPUTS'(XLR-Line level)1 & 2 -- To connect sources with balanced (XLR) outputs.
  13. PHONO GROUND - To connect to a turntable grounding terminal.
  14. ANALOGUE OUTPUT (RCA,variable level)3 & 4 - To connect to a power amplifier, headphones etc..
  15. ANALOGUE OUTPUT (XLR,variable level)4 - To connect to a power amplifier, headphones etc...
  16. HDMI INPUTS' & HDMI OUTPUT with ARC/eARC (HDMI)7 - To connect sources with 1.4 & 2.07 HDMI output and TV with ARC capability.


Notes:
1 Analogue inputs: Input range adjustable 1V-4V rms, impedance 10kΩ
2 with ADC of 192kHz/24bit
3 RCA Output Audio transformer option ONLY
4 Independently switchable allowing either RCA or XLR, RCA and XLR outputs. Check HERE
5 Digital inputs: 32kHz, 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz
6 USB Supported Sample rates: 44.1k, 48k, 88.2k, 96k, 176.4k, 192k, 384k
7HDMI Premium certification.pngLinn recommend using Premium High Speed Certifiied HDMI cables for an optimal experience. (supporting HDCP 2.2 up to and including 60Hz UHD.)




Klimax DSM (Music variant)

KDSM Black Rear Panel Music 700px.png
View Klimax DSM (Music) detail - 1,2,3,4.......
Information of what each connector is and a basic specification of these connectors

Click for more....
  1. MAINS INPUT - To connect to the mains electricity supply.
  2. ETHERNET - To connect to a network (100Base-T / 1000Base-T)
  3. USB-A socket: for Service Use only This socket does not accept USB sticks / USB-Drives
  4. FIBRE ETHERNET - SFP module socket to connect to a fibre network
  5. FALLBACK - To put the device into Fallback mode (used when reprogramming)
  6. USB-B socket - To connect to a PC/MAC for Class 2.0 PCM Asynchronous USB Audio playback6
  7. OPTICAL DIGITAL INPUT (TOSLINK)5 - To connect sources with TOSLINK (optical) digital outputs.
  8. DIGITAL INPUT/OUTPUT (SPDIF)'5 - To connect sources with SPDIF(BNC) digital outputs or use as an SPDIF digital output.
  9. DIGITAL INPUTS (SPDIF)5 - To connect sources with SPDIF(BNC) digital outputs.
  10. EXAKT LINK - To connect to Exakt compatible devices (Exaktbox, Exakt Speakers, Urika II etc)
  11. ANALOGUE INPUTS (RCA-Line level)1 & 2 - To connect sources with RCA analogue outputs.
  12. BALANCED INPUTS'(XLR-Line level)1 & 2 -- To connect sources with balanced (XLR) outputs.
  13. PHONO GROUND - To connect to a turntable grounding terminal.
  14. ANALOGUE OUTPUT (RCA,variable level)3 & 4 - To connect to a power amplifier, headphones etc..
  15. ANALOGUE OUTPUT (XLR,variable level)4 - To connect to a power amplifier, headphones etc...



Notes:
1 Analogue inputs: Input range adjustable 1V-4V rms, impedance 10kΩ
2 with ADC of 192kHz/24bit
3 RCA Audio transformer option ONLY
4 Independently switchable allowing either RCA or XLR, RCA and XLR outputs. Check HERE
5 Digital inputs: 32kHz, 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz
6 USB Supported Sample rates: 44.1k, 48k, 88.2k, 96k, 176.4k, 192k, 384k





Klimax DSM (Hub variant)

KDSM Black Rear Panel Hub 700px.png
View Klimax DSM (Hub) detail - 1,2,3,4.......
Information of what each connector is and a basic specification of these connectors

Click for more....
  1. MAINS INPUT - To connect to the mains electricity supply.
  2. ETHERNET - To connect to a network (100Base-T / 1000Base-T)
  3. USB-A socket: for Service Use only This socket does not accept USB sticks / USB-Drives
  4. FIBRE ETHERNET - SFP module socket to connect to a fibre network
  5. FALLBACK - To put the device into Fallback mode (used when reprogramming)
  6. USB-B socket - To connect to a PC/MAC for Class 2.0 PCM Asynchronous USB Audio playback4
  7. OPTICAL DIGITAL INPUT (TOSLINK)3 - To connect sources with Toslink (optical) digital outputs.
  8. DIGITAL INPUT/OUTPUT (SPDIF)3 - To connect sources with SPDIF(BNC) digital outputs or use as a SPDIF digital output.
  9. DIGITAL INPUTS (SPDIF)3 - To connect sources with SPDIF(BNC) digital outputs.
  10. EXAKT LINK - To connect to Exakt compatible devices (Exaktbox, Exakt Speakers, Urika II etc)
  11. ANALOGUE INPUTS (RCA-Line level)1 & 2 - To connect sources with RCA analogue outputs.
  12. BALANCED INPUTS'(XLR-Line level)1 & 2 -- To connect sources with balanced (XLR) outputs.
  13. PHONO GROUND - To connect to a turntable grounding terminal.
16 HDMI INPUTS' & HDMI OUTPUT with ARC/eARC (HDMI)5 - To connect sources with 1.4 & 2.05 HDMI output and TV with ARC capability.


Notes:
1 Analogue inputs: Input range adjustable 1V-4V rms, impedance 10kΩ
2 with ADC of 192kHz/24bit
3 Digital inputs: 32kHz, 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz
4 USB Supported Sample rates: 44.1k, 48k, 88.2k, 96k, 176.4k, 192k, 384k
5 HDMI Premium certification.pngLinn recommend using Premium High Speed Certifiied HDMI cables for an optimal experience. (supporting HDCP 2.2 up to and including 60Hz UHD.)






Top Of Page Index

Surround examples

7.1ch Surround using all Exakt loudspeakers and Exaktboxes

Klimax Full Exakt 7-1 Surround-800px.jpg

7.1ch Surround using analogue output and Exakt productse

Klimax Full Exakt 7-1 mix.jpg


More Surround options can be seen in the Surround section




Download App

Initial Installation

Linn App
Linn App Searc.png

The Linn DS/DSM can be done from many control points at the same time.

The name of this control App/software is Linn App


Linn App - iPhone/iPad Apple App store - Linn App for iPhone / iPad
        or
Linn App - Google Play for Phone/Tablet Google Play - Linn App for Android Phone/Tablet


Kazoo
Kazoo Playlist iPad.jpg

The Linn DS/DSM can be done from many control points at the same time.

The name of this control App/software is KAZOO..

Kazoo control App/software is available for
Windows Kazoo software download

Windows Kazoo download

OSX Kazoo download

MAC OSX Kazoo download

Kazoo App - Google Play for Phone/Tablet Andrioid Kazoo for Android Phone/Tablet download

You can also download the Apps from: www.Linn.co.uk > Menu > The Linn control App - Kazoo



Setup and changes

Top Of Page Index

Bluetooth & Wifi

Bluetooth and Wifi features are available on Klimax DSM/3
Specs:

Wifi.png Wifi Specification
Supports IEEE 802.11a/b/g/n/ac PSK/CCMP 1-CH

[ 2.4G (b/g) & 5G (n) Standards]

Bluetooth-icon.pngBluetooth Specification
Reception of Bluetooth Audio:

Series 3, Selekt DSM, Majik DSM (2020 variant) & Klimax DSM (2020 variant) implements Bluetooth v4.2

  • Audio is transferred using SBC encoding
  • This is not natively compatible with Googlecast.

Quick setup can be done using the Pin buttons or the Klimax dial

Klimax DSM 2021 BLUETOOTH PINS.png

Setting up Bluetooth using the Pin buttons

1. Select the Bluetooth menu on your device for pairing
2. Press and hold Pins 3 & 4 on the Klimax DSM until "Bluetooth: Pairing..." appears on the front panel display
3. Select the Klimax DSM from the list of available Bluetooth devices on your device for pairing




Klimax DSM 2021 WIFI PINS.png

Setting up Wifi using the Pin buttons

1. Remove/disconnect any cable LAN connections from the Klimax DSM
2. Press the WPS button on your internet router
3. Press and hold Pins 2 & 5 on the Klimax DSM until "WPS: Connecting..." appears on the front panel display
4. The Klimax DSM should now automatically connect to the Wifi network
  • Press and hold Pins 1, 2 & 5 to forget the Wifi network




KlimaxDSM-3 Dial.jpg

Setting up Bluetooth or Wifi using the Klimax dial

1. With the Klimax DSM out of Sleep mode. (If Wifi setup disconnect any cable LAN connections)
2. Press dial UP to enter Service menu
3. Scroll UP/DOWN to highlight "Connect"
4. Press RIGHT to select this menu
5. Scroll UP/DOWN to highlight the desired option and RIGHT to select
Wifi (WPS): put your router into WPS discovery mode for auto pairing of the Klimax DSM
WIfi (Reset): to clear any previous Wifi settings
Bluetooth Pair: configure you Bluetooth device for pairing before selecting
Press LEFT to cancel Service menu

Alternative Wifi Setup Method via Web Browser

1. With the Klimax DSM out of Sleep mode and cable LAN connections removed from Klimax DSM
2. Go to the Wireless settings on your device (e.g. iPad)
3. Find the Klimax DSM on the list of available networks. It will be called Klimax DSM - <serial number>
4. Select this Linn DSM as the wireless network
5. Now open a web browser on your device and type "https://setup.linn.co.uk" in the address bar
6. The Klimax DSM Wifi Setup page should now be displayed
7. Select the Wifi network you want to connect to
8. Enter the passkey for the Wifi network
9. Click on 'Set Network'




Wifi can also be setup using the Konfig App or Manage_Systems below

Konfig / Manage Systems

There are two ways to configure, (if required), your Linn DS/DSM player/Speakers etc:

1. Web-browser App called Manage systems that can also be used on your Tablet:
Product page.jpg

Before you do anything you will need to have a Linn Account. This is a simple process and can only be performed using the Kazoo App or Linn App.
Details on how to create your Linn Account and how to use Manage systems can be found in the Manage Systems page.



2. Windows 10 PC or MAC OSX app called Konfig:
Configuration.png

This Konfig App can be downloaded from KONFIG App

This will allow changing the Room name, Kiko name, input name and other settings. This can be changes by yourself and/or your Linn Retailer.

Details of most of the options are listed in the Konfig Manual, this covers many options

Konfig is currently being phased out and replaced by Manage Systems.



Note: Manage Systems has taken over from Konfig and we would prefer you to use Manage Systems to setup an configure your Linn products.


Space Optimisation

SPACEOPTIMISATION Logo.jpg
for ALL Linn DS/DSM products
Linn Account Space Optimisation
Linn Account Space Optimisation
from Davaar64 ⇒
Konfig Space.png
Linn Konfig Space Optimisation
& Space Optimisation+

Linn Space Optimisation is currently configurable using either the Konfig app or the Linn Account Manage systems.

Click the above picture/icon for more information of that version of Space Optimisation.

More details of what Space Optimisation can be found can be found at www.Linn.co.uk

What are the differences between the Konfig Space Optimisation and Linn Account (Kloud Konfig) Space Optimisation?

The new version of Space Optimisation uses highly sophisticated acoustic modelling to model the interactions between your speakers and the room; this acoustic modelling is based on the finite-difference time-domain method. A simple two-dimensional analogy to this method of acoustic modelling is of a fishing net laid over a pond; each knot in the net defines a discrete measurement location, so that when a stone is thrown into the pond, we can track the resulting ripple by measuring its height at each knot.
The spatial discretisation employed by this method of acoustic modelling allows the new version of Space Optimisation to correctly consider the effects of:
  • non-rectangular rooms;
  • the placement of features like doors and windows;
  • And the location and rotation of your speakers.
Furthermore, the time-domain formulation of this method of acoustic modelling means that the new version of Space Optimisation can now reduce both the energy and decay time of any artificial distortions caused by the interactions between your speakers and the room, resulting in both a flat frequency response and a uniform decay time. :Finally, the new version of Space Optimisation has been designed to give a better balance of low- and mid-frequency energy.

What is the difference between Space Optimisation & Space Optimisation+?

This is applicable to both Linn Konfig and Manage System/Kloud Konfig
Space Optimisation is for NON-Exakt systems. This uses the direct analogue outputs of the Linn DS/DSM
Space Optimisation+ is for Exakt speaker. This is used for loudspeakers fed via the Exakt-link AND used with as a digital crossover.
The "plus" is to signify the more musical detail that is capable within the Exakt system and Space Optimisation due to timing control of each individual drive unit etc. (This is not possible with non-Exakt systems as the loudspeaker is only driven by one common audio feed per channel.)

Is the Linn Account Manage systems only available for the new Linn DSM's

Both Applications can be used for ALL Linn Products.
The only limitation is that the Linn DS/DSM must have Davaar64 to run Linn Account Manage systems]

Why don't you use a Microphone in Space Optimisation?

The aim of Space Optimisation is to remove the effects of your room, to uncover the unique acoustic characteristics of your speakers; after all, this is what you fell in love with when buying your speakers. To achieve this, Space Optimisation needs to understand both the interactions between your speakers and the room and the unique acoustic characteristics of your speakers; the unique acoustic characteristics of your speakers are then subtracted from the interactions between your speakers and the room, leaving only the effects of your room.

An acoustic measurement of the interactions between your speakers and room can have many sources of error which may affect the accuracy and repeat-ability of the measurement, including the choice of measurement stimulus, such as MLS or a log chirp; external noise, such as traffic noise and vibration; quality and calibration of the microphone, which can introduce distortion; and the microphone location, which can be sensitive to within a few centimetres. The use of acoustic modelling removes these sources of error: the model can apply an ideal impulse as stimulus; the modelling domain is free from noise; the model can use an ideal microphone; and the listening location is well-defined. It can thus be seen that acoustic modelling has a clear advantage over acoustic measurement in understanding the interactions between your speaker and the room.

The unique acoustic characteristics of your speakers depend on many factors, including the shape and size of the drive units and ports; the constructive and destructive interference between the drive units, ports and any cabinet-edge diffraction sources; and the angle between the listening location and your speakers. Therefore, a simple on-axis anechoic measurement of your speakers is insufficient information; what is actually required is an anechoic measurement with your speakers in the same configuration as you have them in your home. While some manufacturers do publish anechoic measurements of their speakers, both on- and off-axis, it is extremely unlikely that they will have performed an anechoic measurement of your speakers in the same configuration as you have them in your home. The acoustic modelling of such a scenario is, however, straightforward; the model can simply turn your room into an anechoic chamber to obtain the unique acoustic characteristics of your speakers in the same configuration as you have them in your home. It can thus be seen that acoustic modelling once again has a clear advantage over acoustic measurement in understanding the unique acoustic characteristics of your speakers.


From the above, it is clear that acoustic modelling is the best approach to Space Optimisation.



Can I use "Linn Account Space Optimisation" with my Exakt system?

From November 2019 you can now use Linn Account Space Optimisation with Stereo and Surround Exakt systems.






Analogue Output Mode

From Davaar firmware 4.81.396 (Apr 2021), you now have the ability to enable/disable the XLR and RCA analogue outputs on the Klimax DSM/3 (AV) & (Music).
For example:
This will allow you to have say, Loudspeakers on the XLR outputs and a headphone amplifier on the RCA outputs.(The Exakt outputs are unaffected in this setup.)




REM022 Star.png
To select the Analogue Output mode using the IR Handset
1. To switch between outputs press and hold * button on the REM022 handset
This will then switch to the other analogue output. If currently on XLR then it will switch to RCA. If currently RCA then it switch to XLR
2. Press and hold * button on the REM022 handset to switch back to the other output.
Manage systems/Konfig and Dial selection will allow you to have both XLR & RCA operational at the same time.







KlimaxDSM-3 Dial.jpg
To select the Analogue Output mode using the top dial
1. With the Klimax DSM out of Sleep mode
2. Press dial UP to enter Service menu
3. Scroll UP/DOWN to highlight "Settings"
4. Press RIGHT to select this menu
5. Scroll DOWN to highlight the "Analog Output" and RIGHT to select
6. Use the UP/DOWN keys to select
RCA Only: to only output on the RCA sockets
XLR Only: to only output on the XLR sockets
Dual (XLR & RCA): to have both RCA and XLR sockets live.
Off: to disable these analogue outputs.
Press LEFT to cancel Service menu




Lip Sync

Lip-sync can be set with a default setting in the Konfig:Device page or Manage Systems: Advanced - "Video Sync Delay (ms)" setting
KlimaxDSM-3 Dial.jpg
To trim these using the IR handset or top dial
1. With the Klimax DSM out of Sleep mode
2. Press dial UP to enter Service menu
3. Scroll UP/DOWN to highlight "Settings"
4. Press RIGHT to select this menu
5. Scroll DOWN to highlight the "Lip-Sync" and RIGHT to select
6. Use the UP/DOWN keys to select trim the lip-sync timing up/down
7. Press LEFT to cancel Service menu










Using the Linn Klimax DSM

Top dial and front panel operation

Klimax DSM 2021 Black Front Shadow web-res.png
1. PIN BUTTONS - Personalised media selection Pins 1-6
Click for more....
* Press the button gently, turned as a "half press" to check what the button will do.
* Fully press the press to button to action/select this PIN operation.


Creation on PINS can be found in the Kazoo Manuals for
Windows 8/10/11,
MAC OSX 10.11+ ,
iPad/iPhone IOS 8+ and
Android 4.1+
2. CONTROL DIAL - Main control dial and switch interface
Click for more....
KlimaxDSM-3 Dial.jpg
  • GO INTO SLEEP:
Press the dial CENTRE and continue to press the CENTRE (approx 2seconds) until the volume indicator dial starts to decrease.
  • BRING OUT OF SLEEP:
Press any of the UP/DOWN/LEFT/RIGHT or CENTRE of the dial.
  • SOURCE SELECT
  1. Press the dial DOWN to list the inputs available menu
  2. Scroll UP/DOWN the selection.
  3. Press RIGHT to select source or LEFT to cancel selection menu
  • PLAY/STOP/PAUSE
A quick press of the dial CENTRE will toggle between PLAY and STOP/PAUSE
(Radio-PLAY/STOP, Playlist-PLAY-PAUSE).
  • TRACK/PRESET PREV/NEXT
A quick press of the dial LEFT/RIGHT jump to Playlist tracks or Radio stations.
  • Volume
Rotate dial clockwise to increase volume, anti-clockwise to reduce volume. The dial indicators will tell you the present volume.
  • SURROUND TRIM
  1. With the Klimax DSM out of Sleep mode
  2. Press dial UP to enter Settings menu
  3. Press RIGHT to select or LEFT to cancel Settings menu
  4. Scroll UP/DOWN to highlight "Surround"
  5. Press RIGHT to select or LEFT to cancel Surround menu
  6. Select a the channel and trim with UP/DOWN


Klimax DSM INFORMATION
  • Software version
  1. With the Klimax DSM out of Sleep mode
  2. Press dial UP to enter Service menu
  3. Scroll UP/DOWN to highlight "Software Update"
  4. Press RIGHT to select or LEFT to cancel Service menu
  • Klimax DSM "Properties" (Room name, device name, IP address etc)
  1. Press dial UP to enter Service menu
  2. Scroll DOWN to highlight "Device" or 'Network"
  3. Press RIGHT to select or LEFT to cancel Properties menu
  • Klimax "Settings" (|Balance, Lipsync, Surround volumes, Connect (Blutooth/Wifi) etc)
  1. Press dial UP to enter Service menu
  2. Scroll DOWN to highlight "Settings"
  3. Press RIGHT to select or LEFT to cancel Settings menu

Note: Cancel any previous menus by pressing LEFT key.

3. Volume level & Mute indicators
Click for more....
To show the current volume value and mute condition.
4. Software update available
Click for more....
This is your Klimax DSM telling you that a software update is available.
The update is not compulsary, just an indication that an update is available.
A Software update is performed by the Manage Systems - Software Updates, IR handset or Linn App. Instructions on how to do this update are listed HERE
5. Media information - This will show the source name/track name/Radio station that you are on.
Click for more....
Using the IR handset i button to wake up and further presses allow you to scroll throught the display available.
  • On the Playlist this is typically Artist, Album & codec information. The lower bar will show the track position information
  • On a Radio source this will show the information provided by the radio station and the codec information
......
6. Transport information
Click for more....
Show the Play/Stop/Pause/Buffering symbol to show the current transport state.
7. Mains Power button
Click for more....
Main Power switch totally power off the Klimax DSM


Top Of Page Index

Controlling your Linn DS/DSM using an infrared handset

To control your Linn DS/DSM you can you the infra-red handset supplied with product as well as the Linn App, Kazoo. This can be downloaded & installed

The infra-red handset supplied has;-

REM022-diag.png

  * Volume control, Mute
  * Input control with PIN selection
  * Radio station selection using the handset joystick,
  * Playlist navigation using the handset joystick,
  * Transport control (Play, Stop, Pause, Skip & Search) &
  * Music information.



The Technical Specifications of the IR handset can be found HERE


Control of the Linn DS/DSM using a PC/MAC/Tablets & Phones

Initial installation

Linn App
Linn App Searc.png

The Linn DS/DSM can be done from many control points at the same time.

The name of this control App/software is Linn App


Linn App - iPhone/iPad Apple App store - Linn App for iPhone / iPad
        or
Linn App - Google Play for Phone/Tablet Google Play - Linn App for Android Phone/Tablet


Kazoo
Kazoo Playlist iPad.jpg

The Linn DS/DSM can be done from many control points at the same time.

The name of this control App/software is KAZOO..

Kazoo control App/software is available for
Windows Kazoo software download

Windows Kazoo download

OSX Kazoo download

MAC OSX Kazoo download

Kazoo App - Google Play for Phone/Tablet Andrioid Kazoo for Android Phone/Tablet download

You can also download the Apps from: www.Linn.co.uk > Menu > The Linn control App - Kazoo



Using the Linn DS/DSM control software

For full operation of Kustom DSM you will need to use Linn App and/or Kazoo 4.13.64 >

As you can see from the above section there are multiple software/Apps for different control devices. Although Kazoo has the same style of control in each device, there are minor differences depending on what your control device is. This is why we have different Manuals.
These manuals should only be used as a basic guide for what the buttons can do. We would recommend just using the App/Software and only using the guide if you are having difficulty or want to see what more features are available.

These guides may show some features that are not available, or not have not be configured to work in your system. If you required more information then please contact your Retailer or Linn Support Site


iPad/iPhone/Android Linn App
Windows Kazoo
MAC/MACBook Kazoo
up to Yosemite (OSX 10.10)]
El Capitan (10.11 >)


iPad/iPhone Kazoo


Android Kazoo




Top Of Page Index

Features

USB stream

USB-icon.png
USB Stream
Click for more....

Type: USB-B Asynchronous socket

USB-icon.png
USB Audio Class 2 endpoint with supported sample rates from 44.1k to 384k on Klimax DSM
Connect your iPad/iPhone, with USB-C socket, or PC/MAC to this socket via a USB cable and select LINN DSM 'USB' input as your Audio Device.
PC/MAC will typically transcode the audio into PCM format before feeding down the USB cable to the Linn Klimax DSM
This can also be used to connect your iPhone or iPad with USB-C socket to play Apple Music, at full bandwidth and resolution, on the Linn DSM

Check FAQ for more information

Bluetooth Audio

Bluetooth-icon.png
Bluetooth Audio player
Click for more....

Bluetooth Specification
Reception of Bluetooth Audio: Series 3, Selekt DSM, Majik DSM (2020 variant) & Klimax DSM (2020 variant) implements Bluetooth v4.2

  • Audio is transferred using SBC encoding
  • This is not natively compatible with Googlecast.

Tidal

Tidal-icon.png
Tidal
Click for more....
Tidal-icon.png

Tidal This will work with Linn DS/DSM products running Davaar23 firmware. This can be updated using the Konfig software.

To create and add Tidal tracks to a Linn DS/DSM playlist, you require Kazoo or Linn App
Tidal is supported in countries listed HERE on the Tidal website
Check for Tidal FAQ's with Linn DS/DSM

Qobuz

Qobuz-icon.png
Qobuz
Click for more....
Qobuz-icon.png
Qobuz Streaming CD or Hi-Res quality music
To create and add Qobuz tracks to a Linn DS/DSM playlist you require Kazoo or Linn App
Check for Qobuz FAQ's with LInn DS/DSM

Calm Radio

CalmRadio-Icon.png
Calm Radio
Click for more....
CalmRadio-Icon.png
Calm Radio "Music that helps you get through the day "
To create and add Calm Radio tracks to a Linn DS/DSM playlist you require Kazoo or Linn App
Check Check for Calm Radio FAQ's with Linn DS/DSM

Check FAQ Calm Radio for anymore information

Spotify Connect

Spotify-icon-22.png
Spotify Connect
Click for more....
Spotify-icon-22.png
Spotify Connect can now be used on Linn products using firmware Davaar59 (Aug 2017) or later firmware. (That is, if your Linn Klimax DSM has had a software update after Aug 2017 then you can use Spotify connect)
This allows you to select and play your Spotify music on your Linn DS/DSM players and use the internal volume control on the Linn DS/DSM.

To connect your Spotify account to the Linn Klimax DSM :
  1. On your control device, iPad/Android/PC/MAC etc, connect to the same computer network as your Linn DS/DSM
  2. Start your Spotify app, (if it is already open then close the App, wait a few seconds, and open the App)
  3. Now check the Spotify Speakers icon to find your Linn DS. (In some cases you may have to power cycle your Linn Klimax DSM before this is seen)
  4. Select your Linn product, and you can now play to the Linn Klimax DSM from the Spotify account and control the Linn Klimax DSM volume.

This is web controlled and if your Linn Klimax DSM has already been paired with your Spotify account you will be able to control even if you are not on the same ethernet network.(So be careful that if you accidentally select the Linn Klimax DSM as a Spotify speaker and put the volume up high, and you are not at home)

Check FAQ Spotify Connect for more information.

Roon

Roon.png
"Roon Tested"
Click for more....
RoonReadySymbol.png
from Davaar 106 onwards, (March 2024 >), the following products are also Roon Ready and support RAAT audio distribution:


RAAT is also included with Linn DS/DSM's updated to Organik DAC's



Change Roon Protocol to Roon Ready in Manage Systems > Music tab.
Roon RAAT Enable.png



RoonTestedSymbol.png

All Linn DS/DSM ARE ROON CERTIFIED devices

The Linn DS/DSM requires Davaar63 (May 2018) or later firmware to work with Roon V1.5 and above.(That is, if your Linn DS/DS/HUB has had a software update after May 2018 then you can use Roon)


This allows full hi-res audio, (192k/24bit) playback controlled by the Roon system

Songcast is used to share audio between Linn Products when using Roon. It does not use RAAT (Roon Advanced Audio Transport) for sharing Music, so cannot be set up as a Roon-Ready sharer.

Roon Tested Setup
On Linn DS proxy setups, Linn DS with Linn Kontrol preamplifier connected with RS232, the Roon volume control will not control the Linn Kontrol volume. This will only work with Linn DSM or Linn DS with internal volume control disabled.
A Roon HUB is required in your network system to allow Roon to control your Linn DS/DSM.
ENABLE the Linn DS/DSM player in the Roon - Settings - Audio - NETWORKED section.
In the Settings > Setup make sure that the Subnet of Linn Streaming is the same as the network that the Linn DS is on. Otherwise, they will not show in the Audio

Control
Primary control is through Roon.
:Transport IR is disabled on the Linn DS/DSM when the Roon input is selected from Linn DS firmware release Davaar80 (Nov 2020)

Issues
Roon uses the Linn DS/DSM as a media player, the control interface IS Roon.

• I cannot see any Linn DS in the Audio list...
If you cannot see any Linn DS product in the Audio list then check that with the setup the correct Linn Streaming subnet (network address range).
E.g. if your Linn DS has IP address 192.168.1.34 then its subnet is 192.168.1.0
Roon-Subnet for Linn.png
• I am only getting Airplay quality audio from the Linn DS using Roon
In Roon: Settings - Audio setup page, you will have devices listed with "via Linn Streaming" and devices listed with "via Airplay".
Pressing this ENABLE button on "via Linn Streaming" will bring this Linn DS player alive.
When you press ENABLE, this will then allow you to rename this Linn DS, otherwise it will be its default name. E.g. below the "Linn Akurate DSM" - "via Linn Streaming" has been enabled and I have renamed it "Merlin Lounge".
Airplay-setup.png


The Linn DS/DSM products have to be declared as "Roon Tested", networked devices in the Roon Core settings. (The "AIRPLAY" option for the Linn DS/DSM must be disabled within the Roon Core).
Roon-Tested-setup.png
Click on the Roon Ready - Enable and give a name to the Linn DS/DSM. (In the example below, this has been named Merlin Lounge)
• I press STOP and the Roon starts playing again...
Transport (play / pause / stop) and Volume can be controlled using Kazoo or Ir handset. Although later versions of Roon will counteract these commands. Only use the Roon controller software to control what is playing.
Linn DS Firmware Davaar80 onwards will disable transport controls whilst on the Roon input of the Linn DS/DSM
• If I select an external source whilst playing Roon, I need to reselect the source to get it playing.
This can be due to a confusion, as the Roon will send a stop command to the Linn DSM as you exit the Roon source. However, as the Linn DSM will probably have changed to this new source, then this new source is stopped by Roon. On external sources, this can only be recovered by selecting another source and going back to the originally selected source.
The solution is to Stop or Pause the Roon source BEFORE you change to a different input on the Selekt DSM.
This can also be reduced by going into Konfig or Manage systems and disabling the "AutoPlay" option.

Deezer

Deezer logo 895px.png


Click for more....
Deezer logo 895px.png
This can now be used on Linn products using firmware Davaar82 (July 2021) or later firmware.
To create and add Deezer tracks to a Linn DS/DSM playlist you require the Linn App
This function is NOT available on the Kazoo or Kinsky Apps
The Deezer is broadcast from the Internet straight to the Linn DS/DSM and you use the Linn App to select and play the Music on the Linn DS/DSM.


Check for Deezer FAQ's with Linn DS/DSM

AIRPLAY

NetAux.png
Airplay
Click for more....
NetAux.png
AirPlay is a Apple protocol that allows wireless streaming media.
The Linn DS/DSM/HUB can take the audio stream via the "Netlink" input.
Check <HERE> for any issues with Airplay

AIRPLAY2

Airplay2.png
Airplay 2
Click for more....
Airplay2.png
AirPlay2 is a Apple protocol that allows wireless streaming media available from Linn DS firmware Davaar 92 (Jun 2022)
The Linn DSM/HUB can take the audio stream via the "Netlink" input.
Airplay2 allows you to Group multiple Airplay 2 devices (including Linn DS HomePod, Apple TV) to play in sync using iOS, Siri, Homekit, iTunes desktop (Windows & MacOS)....

Products supporting Airplay2:


HDMI-2

HDMI-2
Click for more....

HDMI ARC

HDMI-ARC
Click for more....
HDMI Audio Return Channel is the audio returned from the same HDMI cable feeding A/V to the television.
This is only supported on the HDMI-2 board and on the Selekt DSM and on the Series 3.

This input can ONLY be used with a television. If any other HDMI source is connected to this input, then no audio will occur. (The HDMI ARC communication is different to standard HDMI communications)
This HDMI ARC input is declared as a separate input on the Linn DSM/HUB control. This can be set to automatically switch to this HDMI-ARC input when you have just switched on your television. More information on how to set this up are in the Konfig manual

General limitations with ARC are that it doesn't communicate with the playback device, in this case the Linn DSM, what Surround formats that it supports, if any. You need to check within the TV setup that the HDMI-ARC connection will only output in a format/codec that the Linn DSM will support. (2-ch/stereo PCM for a standard Linn DSM/HUB and 5.1ch Surround sound for one with a Linn Surround module).
This does NOT support DSD audio

HDMI eARC

HDMI-eARC
Click for more....

HDMI eAudio Return Channel is the audio returned from the same HDMI cable feeding A/V to the television.

  • This is an updated verison of ARC that supports addtional Audio formats to HDMI. This is currently only supported

  • eARC can have an inbuilt Ethernet connection, but this is NOT used on the Linn DS/DSM.
  • Some Manufacturers TV may need CEC enabled
HDMI cables that worked with HDMI-ARC may not work with HDMI-eARC.
HDMI Premium certification.pngLinn recommend using Premium High Speed Certifiied HDMI cables for an optimal experience.

DSD

DSD-Icon.png
DSD Playback
Click for more....
Products that will play stereo DSD audio
  • Linn DS/DSM players with Katalyst DAC's, from firmware Davaar 60, can play Stereo DSD audio files. This is performed by passing the native DSD stream directly to the Katalyst DAC and letting the DAC do the processing and volume control.
  • All ORGANIK DAC's fitted within the Linn DSM can play DSD audio files.
  • New Klimax DSM (2020 variant)
  • Selekt DSM with "Organik", "Standard" and "Katalyst" DAC's
> Only supported on SLOT #1 of the Selekt DSM. Selekt DSM slots 2&3 will not play DSD audio/



Some important points on DSD playback on the Linn DS/DSM:

  • The DSD audio is ONLY available on the Linn DS/DSM analogue outputs.
The DSD audio stream is NOT supported on:

  • Exakt-link to Exakt speakers or Exaktbox. That is, DSD files will NOT play on Exakt speakers or Exaktboxes.
  • Digital outputs. (TOSLINK, SPDIF)
  • Songcast to other Linn DS/DSM players



  • Supports DSD64 (2.8224MHz) and DSD128 (5.6448MHz) sample rates.
    • DSD256 is only supported on Klimax DSM (2020 variant).
These in the following formats:
  • DSF - Sony format that supports ID3 tags
  • DFF - old Philips mastering format (aka DSDIFF)


  • DSD is NOT supported on external inputs such as Toslink or USB



  • No digital signal processing is possible. This means:
    • No balance control is possible to DSD audio file playback.
    • No Space Optimisation is applied to DSD audio file playback
    • Maximum volume is restricted to 80 (unity gain) on DSD audio file playback. However if you have raised to volume to a higher level e.g. 90, this higher volume is applied to any tracks that are NOT DSD audio files.

  • Linn DSM volume control MUST be enabled
    • If the DSM volume control is disabled you will hear "click"s on the loudspeaker when Play/Pause buttons are pressed or a change in bit-rate on change in tracks


Linn Kazoo Server supports the index and serving of DSD files. Non-indexed DFF files that have no metadata can be browsed by file name using the Kazoo Server Removable drives option.
Asset UPnP server and Minimserver support DSD index and serving to the Linn DS/DSM.


Top Of Page Index

General products manuals and information

Top Of Page Index
Controlling the product User Guide

Product setup:Manage Systems user manual

Space Optimisation (Advanced)

Safety Information

Warranty Terms and Conditions

Third Party Software Copyright


FAQs

Linn Klimax DSM (2021 variant) FAQs

Top Of Page Index

Inputs/Outputs

Can I use both the RCA and XLR outputs at the same time?

This all depandent on the varaint of Klimax DS/DSM

All Klimax DS & Klimax DSM 2011/2014/2016/2018 variants:
We advice that you only use the XLR)output OR the RCA(connector #9) output. Never use both outputs as the RCA will degrade the XLR output audio.(When the output is set to RCA in Konfig/Manage Systems this will ground part of the signal from the XLR-COLD connection.


Klimax DSM 2020 variant:
Yes, you can use both RCA and XLR outputs at the same time. You also have the option in this variant to disable XLR or RCA sockets using the Konfig/Manage Systems.
How can I connect my headphones to the Klimax DSM?
On the Klimax DSM 2020 variant only: from firmware release Davaar 81 (Apr 2021) You can switch on/off the backpanel XLR and RCA analogue outputs. This can allow you to connect your headphone amplifier to one set of sockets and your loudspeaker power amplfier to the other set of output sockets.
This can be actioned by pressing and holding the IR handset * button to toggle the XLR/RCA setup
Is there a TAPE OUT on the Klimax DSM?

No, all Klimax analogue outputs are share the same common Volume control.


Can I plug a USB stick into the USB socket of the Klimax DSM

Type: USB-B Asynchronous socket

USB-icon.png
USB Audio Class 2 endpoint with supported sample rates from 44.1k to 384k on Klimax DSM

The Linn DSM is a USB stream player. It does not recognise a USB hard drive/USB stick as a Music STREAMING source.

Connect this USB socket into a Windows7/8/10/11 PC, MAC or USB socket of an iPad/iPhone and be a Sound card for these devices.1.
• DSD audio will typically be transcoded to PCM, by the PC/MAC, before transporting down the USB cable to the Linn DSM

Note:

1: The Linn DSM will playback the audio dictated by the PC/MAC sound driver.
  • On Mac you can go into the Sound Settings, after you select the USB Output, and adjust what audio format is played.
  • On a Windows PC you will need to get an audio driver that supports higher bit-rates. (For example: Adding a PCI card or module into your PC to get these higher bit-rates)
How can I play my Computer Music on the Klimax DSM?
You can connect the Linn Klimax USB socket, (USB Type-B) to connect to your PC/MAC USB socket. You can then set your sound card to output to the Klimax DSM.
On the Klimax DSM, select the "USB" input. On the PC/MAC, click on the Volume icon on the notification bar and select Linn DSM. The audio from your PC/MAC is now directed to the Klimax DSM as a USB Audio Class 2 endpoint


You have two volume controls for this input: one on the PC/MAC and the other on the Linn Klimax DSM. We would advise leaving the PC/MAC volume at 100% and only adjusting the Klimax DSM volume. This will stop any surprises when you change the Klimax DSM to another input such as Radio and suddenly get an extremely loud radio station.
Is there a DIGITAL/SPDIF output?
You can configure SPDIF1 socket to be an DIGITAL SPDIF output using the Konfig / Manage Systems software.



Klimax display questions

Putting my hand towards the Klimax DSM is not waking up the display, why not?
The Klimax DSM has a proximity sensor, (that can be disable in Konfig/Manage Systems > Display). This will only work if you move your hand to the front panel display.
(The Selekt DSM has a similar sensor that will also wake the display if you move your hand to the dial. But due to the machined casing on the Klimax DSM this proximity sensor is only operational on the front panel display.)
I get a flashing volume bars on the volume dial, what does this mean?
KDSM-Mute-Dial-200px.gif This is stating that the Klimax DSM is in MUTE.



My Klimax DSM has a RED Linn symbol on the dial, what does this mean?
KDSM-Network-Dial-200px.gif If you do not have a live network/LAN connection on the Klimax DSM the Linn symbol on the dial will go red.

If your network cable is plugged in and your network/LAN is alive then check that you have the network/LAN cable plugged into the LAN socket,

Klimax DSM 2021 Dial-Normal 200px.png After a live network/LAN connection is made the LINN symbol on the dial will turn white after 5-10 seconds.



I get a flashing Linn icon on the volume dial, what does this mean?
KDSM-Exakt-Dial-200px.gif
This means that the Klimax DSM is in :
  • Searching for Exakt speakers after being woken from Standby (typically only flashes for a couple of seconds after waking from Standby)
or
  • FALLBACK mode : Fallback is a state that means that the product is waiting for a software update. To stop this flashing either:
  • Power cycle (Switch Mains Off for 10seconds and then switch mains On) and leave the Klimax DSM to startup for approximately 1min.
or
Display is showing this icon beside the Volume indicator. What does this mean?
Update Available.jpg Firmware update is available.
The update is not compulsary, just an indication that an update is available.
A Software update is performed by the Manage Systems - Software Updates, IR handset or Linn App. Instructions on how to do this update are listed HERE



Is it normal that the Klimax DSM display cannot always stay on? Can I adjust the display timeout?
We aimed for a display that was unobtrusive when idle. The display automatically activates, drawing the user's attention, when there is a change in DSM state to communicate. E.g. changes to volume, source or track would all cause the display to activate. It is also possible to manually activate the display at any other time by pressing the 'i' (information) button on the handset or by moving towards the Klimax DSM front panel display , activating its proximity sensor.

What does the shimmering dial mean?
KDSM3-reboot-dial 200px.gif



This is to show that the Klimax DSM is starting up after a mains power on.
It will typically do this for 30-45 seconds, but if the Linn Klimax DSM is performing a software update this may take a little longer.






IP Network

How do I find the IP address of my Klimax DSM?
When the front panel display is asleep, looking on the top of the Klimax DSM:
  1. Press the UPPER part of the dial. The front panel display will now show System options.
  2. Press the LOWER part of the dial to highlight "PROPERTIES"
  3. Press the RIGHT part of the dial to select this option.
This Klimax display will now show the Klimax Properties and IP Address.
The above action can also be performed using the Linn IR handset joystick controls.



Reseting the Klimax DSM

How do I do a FACTORY reset on the Klimax DSM?
You will need to have the Konfig or Manage Systems to do the Factory Reset, plus internet access for the Klimax DSM
This will do a reset all setting to default setting. This action may take a short time, typically 60seconds, to perform this action.
Konfig
  1. Make sure that your Klimax DSM is powered on and your LAN network has Ethernet access
  2. In Konfig go into the Advanced and find your Klimax DSM
  3. Press the RESTORE and leave it to do the update.
  4. After approx 60seconds your Klimax DSM will have been set back to Factory setting.
  5. All Done
or
Manage_Systems
  1. Make sure that your Klimax DSM is powered on and your LAN network has Ethernet access
  2. Go into Manage systems and select your Klimax DSM
  3. Click on the General tab and scroll to the bottom of the page and you will find the "RESTORE FACTORY DEFAULTS".
Click this text to promote a Factory reset of your Klimax DSM
How do I RECOVER on the Klimax DSM?
You will need to have the Konfig or Manage Systems running to do the full RECOVER, plus internet access for the Klimax DSM
This will do a fresh reload of Software and reset all setting to default setting. This action may take some time to perform as it need to download new software packages and install them. Typically this maycan take one hour to perform.(The is dependant on your Internet speed and how many software versions need to be installed).
Konfig
  1. Make sure that your Klimax DSM is powered on and your LAN network has Ethernet access
  2. In Konfig, go into the Advanced and find your Klimax DSM
    1. If you cannot see you Klimax DSM double check the power connections and network connection.
    2. if you still don't have the Selket DSM listed in Konfig press the FALLBACK ( #2 in the image below) and repeat checking Konfig>Advanced tab
  3. Press the RECOVER and leave it to do the update.
  4. After approx 60minutes go to the Klimax and using the Dial what Software Version is installed.
  5. All Done
or
Manage Systems

This is only valid for Linn DS/DSM that have already been loaded with Davaar 99, or higher, firmware (from approx April 2023). Otherwise, use the Konfig procedure.

If, for any reason, the update process has failed, (for example, you have left this UPDATE running for 2 hours and the Linn DS appears to be stuck), we would suggest doing the following:
1. Power OFF the Linn DS/DSM
2. Power ON the Linn DS/DSM and press the FALLBACK recessed button on the back of the Linn DS/DSM.
(This sometime has the FB label beside a recessed button near the Linn DS/DSM Ethernet socket.)
This should bring a lightening flash symbol on the Linn DS/DSM display.


Linn App-Update and Recovery.png


3 Now open Linn App, click on the LinnAppMoreButton.png icon, and you should now see the System Recovery option


4:Press the > and this will open the product list of products awaiting a RECOVERY.
if no product is listed, then either the Linn App is on the wrong network or the Linn DS/DSM is NOT running Davaar99 or higher firmware. Use Konfig software to recover this Linn DS/DSM.





Linn App-System Recover.png




5: Press the RECOVER button to start the recovery process of this Linn DS/DSM
The button should now state "Recovering" and this may take several minutes to complete.







6.After a few minutes go back to the HOME page, (ignore the recovering button message as this may not have refreshed itself)
Your Linn DS/DSM has been recovered and reset back to factory default setting. I.e. It will be called "Main Room"
Note: Kustom DSM's will not show as a room(s), but are available to be added to your Linn Account in the next step...
7. Within the Linn App, go into the Settings
a) Click on the Linn Account.
b) click on the Add/Remove products.
c) Scroll down the list of products and search for "Main Room" or Kustom DSM. Double check that the serial number listed matches your Linn DS/DSM serial number and hit the + to add it to your Linn account.
8. Proceed to Manage_Systems to rename and set up your Linn DS/DSM

General operation

What is the difference between Klimax DSM (2020 variant) and earlier versions?
Exakt Devices
• Ultra-low jitter clock with improved clock distribution circuitry and new low-noise power supply
• This clock is used as the Exakt master clock and is distributed to all Exakt devices in the system
• Improving the clock in the Klimax DSM (AV / Music / Hub) improves the performance of all Exakt devices in the system
• Klimax Exakt DSM has 4off Exakt sockets, the Klimax DSM HUB only has 2off.
Analogue Inputs
• Brand new, high-performance ADC (analogue to digital converter) which now has its own circuit board and dedicated power supply
• New design has lower noise and lower distortion which benefits all analogue sources
Digital Inputs
• New Linn-designed SPDIF receiver implemented in an FPGA
• Improved clock recovery algorithm for reduced jitter
• SPDIF inputs support up to 192kHz/24-bit audio
• One SPDIF digital input can be configured as an output - This is also possible in the Klimax DSM/2 (2016/208 variant)
• The addition of a USB (type B) input allows connection to a computer as an audio device
USB input supports up to 384kHz/24-bit audio
Streaming
• 384kHz/24-bit streaming support
DSD256 audio format support
Connectivity
• The optical Ethernet connection improves audio performance by providing complete isolation from noisy network components
• WiFi and Bluetooth (4.2) connectivity
• Audio can be streamed from devices such as mobile phones, Alexa, Google Home
HDMI
HDMI eARC support


Differences between the previous version of Klimax DSM and Klimax System Hub
Klimax DSM/3 and Klimax DSM/2 (2016-2018 variant)
KDSM Black Rear Panel AV-Diff KDSM2 606px.png
  1. Addition of Service-Use socket
  2. Addition of Optical Ethernet connection
  3. Addition of USB socket for connection to PC/MAC
  4. Removal of TOSLINK socket from 2off to 1off
  5. Addition of another SPDIF Input. (One socket can still be configured as a digital Input or Output)
  6. Addition of another HDMI-2 input
  7. Addition of third analogue input. (RCA type)




Klimax DSM/3 and Klimax Exakt DSM/Klimax System Hub
KDSM Black Rear Panel AV-Diff KEDSM2 606px.png
  1. Addition of Service-Use socket
  2. Addition of Optical Ethernet connection
  3. Addition of USB socket for connection to PC/MAC
  4. Removal of TOSLINK socket from 2off to 1off.
  5. Removal of 2off EXAKT-LINK sockets from 4off to 2off.
  6. Addition of another HDMI-2 input
  7. Addition of third analogue input. (RCA type)


How to get my Alexa to Play on the Klimax DSM
You need to setup the Linn DSM as Bluetooth speakers for your Alexa
This will then allow you to select your Music to play back on the Klimax DSM as well as the volume of the Music.


Can I plug my USB drive/stick into the USB socket to play Music

Type: USB-B Asynchronous socket

USB-icon.png
USB Audio Class 2 endpoint with supported sample rates from 44.1k to 384k

The Linn DSM is a USB stream player. It does not recognise a USB hard drive/USB stick as a Music STREAMING source.

Connect this USB socket into a Windows7/8/10/11 PC, MAC or USB socket of an iPad/iPhone and be a Sound card for these devices.1.
• DSD audio will typically be transcoded to PCM, by the PC/MAC, before transporting down the USB cable to the Linn DSM

Note:

1: The Linn DSM will playback the audio dictated by the PC/MAC sound driver.
  • On Mac you can go into the Sound Settings, after you select the USB Output, and adjust what audio format is played.
  • On a Windows PC you will need to get an audio driver that supports higher bit-rates. (For example: Adding a PCI card or module into your PC to get these higher bit-rates)

Top Of Page Index

General Linn DS/DSM/HUB Wifi Wifi.png

The Wifi module used with the Linn DS/DSM/HUB supports IEEE 802.11a/b/g/n/ac PSK/CCMP 1-CH

this supports both 2.4G & 5G communications.

Wifi History

2.4G

This was the first Wifi defined in 1997, 802.11b, generally used with 11, or 13 channels depending on your country. Each channel could each supply a data rate of 11MBit/s .
This data rate was then expanded to 54MBit/s in 2003, with the 802.11g. However, this still used 2.4G and instead of using 1channel to communicate it now uses 3-channels to communicate.This reduced your number of usable channels as other device communicating on a channel next door would now encroach into your channel(s).
This means that 2.4G band can have a lot of noise and interference. Coupled with fact that this same frequncy is used by DECT phones, Microwave ovens, Baby mointors, Taxi Radio, Bluetooth.... These can inject a lot if noise and interfere with Wifi streaming link to the Linn DS/DSM/HUB as it may force the LInn product off the Wifi network and it will have to retry the connection, this takes time and may cause your Linn product to keeping muting the Music

5G

A newer standard, 802.11n, allows usage of both 2.4G and 5G to give an even bigger data rate of up to 600Mbit/s.
As standards improve the 802.11ac that the Linn DSM/Series3 supports is a data rato of up to 1,300MBit/s.
5GHz is a much cleaner radio space with a lot less interence compare with 2.4G. The only negative is a slightly reduced range.
Some Wireless-Access-Points, WAPs and Router allow you to setup a seperate SSID, (Service Set IDintifier. this is name for a Wi-Fi network.)

Advice on use

We recommend that you configure your Wifi network to have seperate SSID for 2.4G and a different SSID for 5G wifi. Then configure the Linn DSM/Series-3 to only use the 5G network.
This will then allow the music stream to work on a cleaner transport/Wifi and stop any device from interfering with the music that you are listening to.

There are Apps available to show you what is on your Wifi and your network

Disable Wifi

To totally disable the Wifi, go into the Konfig:About tab and disable the Wi-Fi option.

  • NOTE: In the Konfig:WIFI tab, setting to NONE will only disconnect it from any Wifi network. The DSM will still broadcast its presence on the Wifi network.

Wired LAN connections

If you have connected a LAN cable to your Linn DS/DSM/HUB/SERIES3 then this take priority over the Wifi connection. This means that the Wifi connection is still on but ignored when a there is a live connection on the products LAN socket. When the LAN connection is removed then the connection returns to Wifi. Top Of Page Index

Common FAQ's

How do I Update, or recover, the software on a Linn DS/DSM

This procedure is not difficult. The first step is finding out which software/firmware you are using to minimise the steps required.

From Software version Davaar 99, Konfig has retired from providing software update AFTER this software/Davaar version.
Up to > Davaar 98, then use Konfig to update the Linn DS/DSM to the latest software…
From Davaar99+ then you will need to use the Linn App or IR handset (See point1 below)


To check what version of Software you are running on your Linn DSM, you can either:
1. Use the IR Handset
On the REM 022 use the SHUFFLE key, Press and HOLD this key for 2 seconds
On the REM 020 use the # key, Press and HOLD for 2 seconds,
On older products: early Majik, Akurate, early Klimax and Kiko:
* If this action states, "Your Software is up-to-date" or "Software update available...." then you are running Davaar99 or higher.
* If there is an update available, you will be able to authorise the Linn DS/DSM by pressing the the joystick UP then joystick RIGHT buttons.
* If this states anything else, then you are on Davaar 97 or lower
On newer products: New Majik, Any Selekt DSM & new Klimax DSM:
This will show "Device" on the front panel display. Hit the RIGHT cursor button and this will show you the product information including the software version. (Check point 2, below, on how to decode this version.)
If there is an update available, you will be able to perform this update by following the instructions on the Linn DS/DSM screen.


2: Use Konfig and select your Linn DS/DSM. The Software version is structured as a Software family(4=Davaar) :
Major Release version, (this is the key number to use) : Minor version of software (Ignore this just now)

4:99.491 relates to 4=Davaar, 99=Major software version, 491=Minor version. Therefore, is Davaar-99

Note: Konfig can still be used for these actions, it must still be used as a stepping stone to the latest Linn DS/DSM software.


3. Open Manage Systems and the Firmware is listed on the product configuration page (top right). The Firmware version is decoded in the same manner as the Konfig setup.
Up to Davaar 97
To update, using Konfig and your current Linn DS/DSM firm is Davaar 97 or lower

1.Start Konfig (after ensuring you have latest version)

a) Go into KONFIG Settings and check that Konfig is set to the same network as your Linn DS/DSM.

2. Click on the UPDATES tab. If there is a software update for your Linn DS/DSM it will be listed after clicking UPDATES. If there is no firmware update available for the Linn DS/DSM then it will not be listed under this tab.

Note: on the Selekt DSM & new Majik DSM they will need to be power cycled and wait appox 30minutes before checking the Konfig UPDATES tab
400px‎

3.Select the UPDATE button against the Linn DS/DSM you want to update.

a) A message will appear on the Konfig screen stating the major changes that this software update may incur. (This will be dependant on your present version of software loaded into the Linn DS/DSM)
b) If you want to continue with this update then scroll down to the bottom of the message and select UPDATE.
c) For your Privacy we ask if you agree to collecting Anonymous data on usage of the Linn DS. This will aid any fault reporting and also any activity to help Linn enhance the software and product operation.
d) Select I AGREE or more options to change what information Linn Products Ltd can receive.

4. Konfig will download the firmware update and proceed to updating the selected Linn DS/DSM player.
5.Once complete you will see an Update Completed Successfully message and your DS player will be re-started
6. Update complete

If you encounter any problems, please contact your Linn Specialist or Contact Linn.
From Davaar 99 onwards
To update/recover, using Linn App, and your current Linn DS/DSM is Davaar 99 or higher

Linn Ds/DSM software updates using Linn App

Linn App-Update only.png



1.Click on the LinnAppMoreButton.png icon and if there are any updates for your Linn DS/DSM you will see:





Linn App-Kustom DSM Update.png



2.Press the > and this will open the product list.
As an update is available, STOP ANY MUSIC PLAYING ON YOUR LINN DS/DSM BEFORE pressing the UPDATE button
Tap the Update All to initiate the update of all Linn DS/DSM products shown in the list.
Please be patient as this can typically take between 5–40 minutes to update depending on the complexity of the update.





:



System Recovery

This is only valid for Linn DS/DSM that have already been loaded with Davaar 99, or higher, firmware (from approx April 2023). Otherwise, use the Konfig procedure.

If, for any reason, the update process has failed, (for example, you have left this UPDATE running for 2 hours and the Linn DS appears to be stuck), we would suggest doing the following:
1. Power OFF the Linn DS/DSM
2. Power ON the Linn DS/DSM and press the FALLBACK recessed button on the back of the Linn DS/DSM.
(This sometime has the FB label beside a recessed button near the Linn DS/DSM Ethernet socket.)
This should bring a lightening flash symbol on the Linn DS/DSM display.


Linn App-Update and Recovery.png


3 Now open Linn App, click on the LinnAppMoreButton.png icon, and you should now see the System Recovery option


4:Press the > and this will open the product list of products awaiting a RECOVERY.
if no product is listed, then either the Linn App is on the wrong network or the Linn DS/DSM is NOT running Davaar99 or higher firmware. Use Konfig software to recover this Linn DS/DSM.





Linn App-System Recover.png




5: Press the RECOVER button to start the recovery process of this Linn DS/DSM
The button should now state "Recovering" and this may take several minutes to complete.







6.After a few minutes go back to the HOME page, (ignore the recovering button message as this may not have refreshed itself)
Your Linn DS/DSM has been recovered and reset back to factory default setting. I.e. It will be called "Main Room"
Note: Kustom DSM's will not show as a room(s), but are available to be added to your Linn Account in the next step...
7. Within the Linn App, go into the Settings
a) Click on the Linn Account.
b) click on the Add/Remove products.
c) Scroll down the list of products and search for "Main Room" or Kustom DSM. Double check that the serial number listed matches your Linn DS/DSM serial number and hit the + to add it to your Linn account.
8. Proceed to Manage_Systems to rename and set up your Linn DS/DSM
To update, using an IR handset, and your current Linn DS/DSM is Davaar 99 or higher
Use the IR Handset
On older products, early Majik, Akurate, early Klimax and Kiko,
On the REM 022 use the SHUFFLE key, Press and HOLD this key for 2 seconds
On the REM 020 use the # key, Press and HOLD for 2 seconds,
With older products, early Majik, Akurate, early Klimax and Kiko, If there is a software update it will tell you to press the IR handset UP arrow followed by the RIGHT arrow. The update will now start.
On newer products: New Majik, Any Selekt DSM & new Klimax DSM:
On the IR Handset, or Dial, press the UP joystick key. This will open the setup menu
On the IR Handser, or Dial, press the DOWN joystick key a few times and press the RIGHT joystick key. If there are any software updates on this page it will then give you instructions on how to update the product.

Music formats

What audio formats do the DS players support?
DS products support
  • FLAC Up to 192k 24bit
  • WAV
  • AIFF
  • AIFC
  • MP3
  • AAC
  • WMA (lossy)
  • OGG VORBIS
  • OGG FLAC
  • ALAC (Apple Lossless) upto 192K 24bit (If these ALAC files were generated by an early version of dBpowerAmp the Linn DS will not recognise these. Transcode these files to ALAC using the latest version of dBPowerAmp to fix this.)
  • DSD - limited to some products in a certain configuration. Check DSD Support for more informaiton
Linn recommends FLAC.


Formats NOT supported
  • MQA: Check HERE for more information
  • DRM protected files cannot be played on the DS products


Why does Linn recommend FLAC?
  1. FLAC is a free open format. It is non-proprietary, which means your music collection is safeguarded for the future, can be played through any open digital music player, and is not tied to a particular manufacturer or product. The specification is published for all to see. In contrast, SACD has failed to achieve significant success because it requires proprietary music content and disc players with proprietary hardware inside.
  2. FLAC allows even better than CD quality encoding and decoding. Linn Records provides studio master quality downloads in FLAC, at the same quality as SACD.
  3. FLAC supports metadata, or tags, so that useful information about a piece of music can be stored with the music; for example, album, artist, genre, cover art, sleeve notes, etc. User interfaces can make good use of these tags. Two examples of applications that support tag editing are: Mp3tag (Windows) and Tag (Mac)
  4. Because it is open and free, there are an extensive set of players, tools, transcoders (to convert between other formats and FLAC), tag editors, and other programs for FLAC.



Can the Linn DS/DSM play DSD music?
Products that will play stereo DSD audio
  • Linn DS/DSM players with Katalyst DAC's, from firmware Davaar 60, can play Stereo DSD audio files. This is performed by passing the native DSD stream directly to the Katalyst DAC and letting the DAC do the processing and volume control.
  • All ORGANIK DAC's fitted within the Linn DSM can play DSD audio files.
  • New Klimax DSM (2020 variant)
  • Selekt DSM with "Organik", "Standard" and "Katalyst" DAC's
> Only supported on SLOT #1 of the Selekt DSM. Selekt DSM slots 2&3 will not play DSD audio/



Some important points on DSD playback on the Linn DS/DSM:

  • The DSD audio is ONLY available on the Linn DS/DSM analogue outputs.
The DSD audio stream is NOT supported on:

  • Exakt-link to Exakt speakers or Exaktbox. That is, DSD files will NOT play on Exakt speakers or Exaktboxes.
  • Digital outputs. (TOSLINK, SPDIF)
  • Songcast to other Linn DS/DSM players



  • Supports DSD64 (2.8224MHz) and DSD128 (5.6448MHz) sample rates.
    • DSD256 is only supported on Klimax DSM (2020 variant).
These in the following formats:
  • DSF - Sony format that supports ID3 tags
  • DFF - old Philips mastering format (aka DSDIFF)


  • DSD is NOT supported on external inputs such as Toslink or USB



  • No digital signal processing is possible. This means:
    • No balance control is possible to DSD audio file playback.
    • No Space Optimisation is applied to DSD audio file playback
    • Maximum volume is restricted to 80 (unity gain) on DSD audio file playback. However if you have raised to volume to a higher level e.g. 90, this higher volume is applied to any tracks that are NOT DSD audio files.

  • Linn DSM volume control MUST be enabled
    • If the DSM volume control is disabled you will hear "click"s on the loudspeaker when Play/Pause buttons are pressed or a change in bit-rate on change in tracks


Linn Kazoo Server supports the index and serving of DSD files. Non-indexed DFF files that have no metadata can be browsed by file name using the Kazoo Server Removable drives option.
Asset UPnP server and Minimserver support DSD index and serving to the Linn DS/DSM.


Can I change the audio quality of the Tunein Radio

NO, the Linn DS/DSM.HUB only plays the Radio stream provided by Tunein.

I can no longer get Linn radio stream, Linn Jazz, Linn Classical, Linn Radio, station

From June 2022 TuneIn have removed these Linn Radio streams from their supported list.
These stations are now available using the AirAble-Logo-coloured.png radio. click <HERE> for more information on how to change your LInn DS/DSM radio to AirAble-Logo-coloured.png


Does the Linn DS/DSM players play BBC Radio via TuneIn?

Yes, the Linn DS/DSM/HUB will continue to use TuneIn to access and play the BBC radio stations.
From the 30th September 2019 BBC radio made changes to what can access their Radio stations via TuneIn. This is mainly for devices that can support using the BBC Sounds App. The Linn DS products do not support the Sounds App can will continue to have BBC Radio playback rights using Tunein.
Check the BBC Sounds >HELP< section for more information.

How do I add BBC Radio stations to my Presets?

  1. Select the TuneIn button in Kazoo /Linn App and find the BBC, or any other Radio station you wish to add in selection tree
  2. Press the three dots on the right hand side of the station and enable/disable the Favourite, (TuneIn > Favourite in Linn App).
  3. Complete

I cannot get any foreign Radio stations, I can only get UK stations

Due to a legal case between TuneIn and Sony Music, Warner Music. on licences. UK radio stations have licences for UK wecasting. However, non-UK based radio stations were not licensed to webcast music within the UK,
This is a TuneIn issue we are waiting for them to resolve. The alternative is to configure the Linn DS/DSM with airable internet radio


Does the Linn DS/DSM players play MQA?
No, check this link "MQA is bad for Music" for more information
Can the DS player play multi-channel files?
No, the Klimax DS, Akurate DS, Majik DS, Majik DSI, Sneaky Music DS, Sekrit DS, Sneaky DSM, Sekrit DSM and Sekrit DSi are stereo audio only.

Klimax DSM, Akurate DSM & Majik DSM can play multi-channel audio from their HDMI inputs if they are using Davaar55 or later software.


Upgrading software

How do I upload new software into the Linn DS/DSM
  1. First of all you need a PC or MAC and install the KONFIG app.
  2. After you have installed KONFIG go to the ADVANCED tab. If your Linn DS/DSM requires an update it will be listed here.
  3. If an update is available for that Linn DS/DSM then press the UPDATE' button

More detailed instructions are listed HERE



Physical Input/Outputs

How do I add Music to play on Linn DS
If your Music is on a CD then this must be RIPPED from the CD first.


This can be using a PC or MAC with CD-ROM drive or from a Network attached Storage device/NAS with inbuilt ripper.
If you are using a PC or MAC you can use software listed HERE
The "Ripped" Music can be held on the PC/MAC of on a Network attached Storage device/NAS. The NAS is the better option as this is a low power device that can be left on all of the time.
The PC/MAC/NAS requires UPnP Media Server software to share the Music for the Linn DS/DSM to play.


Will downloaded music play on the DS players?
Yes, so long as it is not protected by Digital Rights Managemant (DRM) restrictions and is in one of the supported formats, or transcoded to such a format.
Can I Airplay from my Android device?
The newer products with Bluetooth allow Android devices to play on a Bluetooth device, that is, the Linn DSM.

Otherwise without ROOTING, the android device there is no way to stream to the Linn DS (Airplay AOA Service).
All other apps take the media file and stream it via UPnP.
Streaming local files can be done use Skifta and “Double Twist Player”
Media Applications


After Updating to Davaar55 I can only get audio from my Exakt outputs and not the Analogue Out
Check Konfig > Device > "Dual Analogue/Exakt Stereo Output" has been enabled.
If you have declared your Exakt speakers as 'Front Left'/'Front Right' and the analogue outputs to be 'Front Left'/'Front Right' (Stereo). ensure that this option in Konfig is enabled. The audio in the Exakt outputs will be out of sync by approx 45mS compared to the analogue outputs.



Are the Digital outputs (Toslink/SPDIF) volume controlled?
No, the digital outputs are ALWAYS full line level outputs. They are not Volume controlled or Mute-able from the standard Linn DS/DSM controls.
The Digital outputs will always produce the front Left & Right of the audio source that is playing on the Analogue or Exakt outputs.


General Q's

Can I stop the kids from playing with the front panel buttons?
Yes on of the Majik & Akurate DS/DSM/HUB. If you go into Konfig > Display settings you can define "Front Panel buttons" to be OFF. This will stop the front panel buttons from doing anything. You can still control the Linn DS/DSM by IR handset and the Kazoo App.
(Just remember if you have disabled the front panel buttons and think that the Linn DS/DSM is broken!)


How do I achieve gapless playback for live albums?
To guarantee gapless playback, you will need to rip your music tracks into a lossless format (i.e. FLAC). You must also ensure that you are using ripping software that does not add gaps between tracks when ripping (i.e. DBPoweramp). Most ripping software will offer the option to turn this feature off.
Also make that that you have selected the PLAYLIST input and NOT the UPnPAV input

Linn PINS

What is a PIN, check HERE for more detailed information.

PIN FAQs:

  • We currently support pinning from Kazoo Server (V4.9.8 onwards) , Tidal, Qobuz, TuneIn, CalmRadio, DS radio presets, and Linn DSM external inputs
  • This is only applicable with Linn DS/DSM players with Davaar 64 or higher firmware
  • This currently does NOT support Pins to external pre-amplifier inputs, such as Akurate Kontrol, Kisto etc.
  • PINs use discrete IR codes and are not used with any other Linn Product control.
  • PINS for Radio stations are wrongly created with Kazoo V4.13.21, this has been fixed with next version 4.13.22. If you have created a Radio station PIN and it doesn't work, check you have a later version of Kazoo and re-assign this PIN to the correct radio station.



Deezer on the Linn DS/DSM

Deezer logo 895px.png
This can now be used on Linn products using firmware Davaar82 (July 2021) or later firmware.
To create and add Deezer tracks to a Linn DS/DSM playlist you require the Linn App
This function is NOT available on the Kazoo or Kinsky Apps
The Deezer is broadcast from the Internet straight to the Linn DS/DSM and you use the Linn App to select and play the Music on the Linn DS/DSM.


Check for Deezer FAQ's with Linn DS/DSM

Linn Songcast

Songcast is the method of transport for streaming STEREO audio data between a Songcast sender, (Linn DS/DSM, Songcast App), and Songcast receivers, (other Linn DS/DSM players listening to that sender DS - multiroom operation.)
The Songcast stream contains the raw unprocessed music stream, the metadata information for the Music playing and timing information.
  • The raw music data is the same data as received by the sending Linn DS. This maintains the same music stream is processed by ALL Linn DS players, (sender and receivers).
    • As this Songcast music stream is untouched this leaves the receiving Linn DS/DSM to do its own volume control.
    • Volume, Space Optimisation and Exakt processing, if used, are all performed as a final process to minimise any digital processing.
  • The timing information is used to ensure that the Linn DS/DSM players are in sync with the music sender.


There is a ! on the front panel of my Linn DS/DSM

There is a speaker setup issue on the Linn DS/DSM Surround Sound Rules



The front panel of the DS is showing a flashing dot or lightening flash and I cannot see the Linn DS with Kazoo or Konfig

This is the Linn DS either in "startup" mode or in "Waiting for Software" mode.

"Startup": The flashing dot is the startup mode trying to connect to you ethernet network. This mode will typically occur when you first apply power to the Linn DS/DSM. This will typically take 30seconds and go into standard use mode.

"Waiting for Software": The lightening flash is the Linn DS/DSM waiting or getting a software update.

If you have any problems getting the Linn DS on an Ethernet network, (dot continuously flashing), try the following options:- Option1

  • Power off the EVERYTHING connected to the Ethernet system, (PC, Printers, DS, Routers/DHCP servers).
  • Leave everything powered off for at least 10seconds.
  • Switch everything back on.
  • Retry the system

You will find that some of the devices in the system get confused and cause system confusion. The power cycling will do a reset of the system and recover most issues.

Option2

  • Use fresh Ethernet cables, (replace existing cables).
  • If the Linn Ds is more than 3M (10ft) from the DHCP/Server. Move the Linn DS right beside the Router/DHCP server and patch using a short Ethernet cable (1M), the Linn DS to the DHCP server/Router
  • Retry the system

Option3

  • Build a totally separate system with only a DHCP/Server and Linn DS.
  • Retry the system

Some networks only have a limited number of DHCP address’s. if you have already connected some PC’s to this system, your Router/DHCP server can remember these devices, (even though no longer connected) and will not allocated these previously assigned IP addresses to newly connected products. So the case of unplugging one device to free up an IP address for the DS to use will NOT work with most Routers/DHCP servers if there are no free DHCP IP addresses available.

This will give a better idea as to what is causing the problem. (98% of the time, this is due to a local network issue).

If you always get the flashing dot then the lightening flash symbol then the Linn DS/DSM needs to be programmed. Check the Konfig Manual > Updates section or contact your Linn Retailer to get assistance.



FAQ on ALL products link

Click HERE for FAQ on ALL products


Troubleshooting

Top Of Page Index
For information on: troubleshooting, Surround options, "Ripping" Cd's , Exakt system then this next section will provide the information that you need:



Technical Specifications

Top Of Page Index

Linn Klimax DSM / 3

Overview
Product Name:

KLIMAX DSM/3

Date of Introduction: March 2021



Type: Digital music player with Organik

Variants:
• Klimax DSM AV with full capabilities (EXAKT + HDMI)
• Klimax DSM Music with no HDMI capabilities
• Klimax DSM Hub with only Exakt audio outputs
Dimensions

(H) 126 mm x (W) 350 mm x (D) 350 mm
(H) 4.96 inches x (W) 13.8 inches x (D) 13/8 inches

Weight 16.4 kg / 36.1 lb
Mains supply voltage (auto ranging)
100–120 V ac (±10%) 50–60 Hz
200–240 V ac (±10%) 50–60 Hz
Expected energy usage 50-70W
Screen Type 1600 x 480 TFT display
Construction Machined from Solid Aluminium
Finish Silver Anodised, Black Anodised
Supported file types FLAC, WAV, MP3, AAC, AIFF/AIFC, ALAC, OGG/VORBIS, WMA, DSD (DSF and DFF)
Audio sample rates 7.35 k, 8 k, 11.025 k, 12 k, 14.7 k, 16 k, 22.05 k, 24 k,29.4 k, 32 k, 44.1 k, 48 k, 88.2 k, 96 k, 176.4 k, 192 k, 384 k
Word depths 16–24 bits
Control protocol Compatible with UPnP™ media servers, UPnP™ AV 1.0 control points
Ethernet 1G Base-T RJ45 / SFP Optocal (1G)
EXAKT 2off
inputs
KLIMAX DSM (AV) KLIMAX DSM (MUSIC) KLIMAX DSM (Hub)
4off HDMI 2.0
4off HDMI 2.0
1off HDMI ARC/eARC
1off HDMI ARC/eARC
1off Ethernet
1off Wifi -
Supports IEEE 802.11a/b/g/n/ac PSK/CCMP 1-CH
1off Bluetooth
Bluetooth v4.2
  • Audio is transferred using SBC encoding
  • This is not natively compatible with Googlecast.
2off Unbalanced (RCA) Line level,
Input sensitivity Selectable: 1 / 2 / 4 Vrms
Input impedance - 50 kΩ
1off Balanced (XLR) Line level,
Input sensitivity Selectable: 2 / 4 / 8 Vrms
Input impedance - 50 kΩ
1off Toslink
Supports 16/24-bit audio at 32kHz, 44.1kHz, 48kHz,
88.2kHz, 96kHz, 176.4kHz, 192kHz
2off SPDIF
Supports 16/24-bit audio at 32kHz, 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz
Nominal input voltage 0.5 V peak
1off USB (type B)Audio Class 2
Supports 16/24-bit audio at 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz, 352kHz, 384kHz
2off Exakt-Link
Sources

     LAN
     Internet radio
     Tidal
     Qobuz
     Calm Radio
     Spotify Connect
     NetAux

AUDIO OUTPUTS
KLIMAX DSM (AV) KLIMAX DSM (MUSIC) KLIMAX DSM (Hub)
Line Output:
1off RCA:

Output Level: 2V rms ( 0dBFS @volume 80 )



Output Impedance: 150Ω



1off XLR:

Output Level: 4V rms ( 0dBFS @volume 80 )



Output Impedance: 300Ω

The XLR output can be disabled and RCA output left running and vice-versa. Both Line outputs can be used simultaneously

2off Exakt-Link
1 x SPDIF
(SPDIF1 connector can be configured as an input or a fixed volume stereo digital output)
Video Outputs
KLIMAX DSM (AV) KLIMAX DSM (MUSIC) KLIMAX DSM (Hub)
1off HDMI 1.4/2.0
1off HDMI 1.4/2.0


Top Of Page Index