Difference between revisions of "Akurate DSM /3 (2018 Variant)"

From LinnDocs
Jump to: navigation, search
m
m
Line 101: Line 101:
 
For further assistance, try our [http://www.linn.co.uk/linn_customer_support customer support] pages
 
For further assistance, try our [http://www.linn.co.uk/linn_customer_support customer support] pages
  
[[Category:Linn_DSM]][[Category:Exakt]][[Category:Katalyst]] [[Category:Exakt_DS/DSM/HUB]]
+
[[Category:Linn_DSM]] [[Category:Katalyst]] [[Category:Exakt_DS/DSM/HUB]]

Revision as of 15:28, 16 March 2022

<< Akurate DSM/2 (HDMI-2 Variant) Akurate DSM/0 (Original Variant) >>

AKURATE DSM/3
(KATALYST)

AkurateKontrolFrontTop.jpg

Product info

  • Product Name: Akurate DSM/3 (Variant 2018)
Other variants of this product can be found at Akurate DSM varinats
  • Software version: Akurate DSM Mk3
  • Date of Introduction: March 2018
  • Type: Integrated digital music player and preamplifier


Hardware Upgrades


Note: It should be noted that this upgrade information may at times be out of date and should not be used as a current list of what upgrades are available

Support

Linn Support Site

Latest software

Latest software releases

Details of latest Product release software

Manuals

Quickstart Guide

Using the Linn DS/DSM/HUB with IR handset, PC, MAC, Android tablet, iPad/iPhone...
Remote Control manual
Manage Systems manual
Space Optimisation (Advanced)
Surround Sound with Exakt systems
Safety Information
Warranty Terms and Conditions
Third Party Software Copyright


Network Setup

Back Panel Connections

Akurate DSM 1 rear.jpg
  1. MAINS INPUT - To connect to the mains electricity supply.
  2. FALLBACK - To put the device into Fallback mode (used when reprogramming)
  3. ETHERNET - To connect to a network (100Base-T)
  4. EXAKT LINK - To connect to Exakt compatible devices (Exaktbox, Exakt Speakers, Urika II etc)
  5. ANALOGUE INPUTS (XLR, line level) - To connect an analogue source with balanced (XLR) outputs.
  6. ANALOGUE INPUTS (RCA, line level / phono) - To connect a line level or turntable analogue source with unbalanced (RCA) outputs.1
  7. PHONO GROUND - To connect to a turntable grounding terminal.
  8. ANALOGUE OUTPUTS (XLR,variable level) - To connect to a preamplifier (or power amplifier when internal volume control is enabled) with balanced (XLR) analogue inputs.
  9. ANALOGUE OUTPUTS (RCA, variable level) - To connect to a preamplifier (or power amplifier when internal volume control is enabled) with unbalanced (RCA) analogue inputs.
  10. DIGITAL INPUTS (Spdif) - To connect sources with Spdif (RCA) digital outputs.
  11. DIGITAL OUTPUT (Spdif) - To connect to an external DAC or computer that has an Spdif digital input.
  12. DIGITAL INPUTS (Toslink) - To connect sources with Toslink (optical) digital outputs.
  13. DIGITAL OUTPUT (Toslink) - To connect to an external DAC or computer that has a Toslink (optical) digital input.
  14. HDMI INPUTS - To connect sources with HDMI outputs 2
  15. HDMI OUTPUT - To connect to a display device with HDMI inputs 2 and HDMI-ARC
  16. EARTH GROUND - To connect to an earthing terminal if no mains earth is available or to join to the earths of other products in the system to improve performance in areas of poor/noisy electrical earth conditions.


1 Input 2 is line level only. Input 3/PH is a configurable input, which is factory set as a moving coil phono input for connection to turntables. This can be changed by a Linn dealer to a moving magnet phono input or a line level input.
2 HDMI Premium certification.pngLinn recommend using Premium High Speed Certifiied HDMI cables for an optimal experience. (supporting HDCP 2.2 up to and including 60Hz UHD.)




Front Panel Connections

Akurate DSM front.jpg
  1. MUTE BUTTON - Mutes/unmutes the audio
  2. VOLUME ADJUST BUTTONS - Changes the volume up/down
  3. SOURCE SELECT BUTTONS - Changes to the previous/next source
  4. SLEEP BUTTON - Brings the unit in/out of sleep mode
  5. FRONT PANEL DISPLAY
  6. HEADPHONE OUTPUT - To connect to stereo headphones with a 3.5mm input (Output Impedance <2Ω)
  7. AUX SOURCE INPUT - To connect to a stereo audio source with a 3.5mm output 2
  8. POWER SWITCH- Switches the power on/off


Installation

Please read the following carefully before installing the unit in your system – your unit may need to be reconfigured by your Linn retailer.

Exakt options

Exakt usage with the Akurate DSM/3 can be found in Akurate_Exakt_System


FEATURES

Tidal

Tidal-icon.png
Tidal
Click for more....
Tidal-icon.png

Tidal This will work with Linn DS/DSM products running Davaar23 firmware. This can be updated using the Konfig software.

To create and add Tidal tracks to a Linn DS/DSM playlist, you require Kazoo or Linn App
Tidal is supported in countries listed HERE on the Tidal website
Check for Tidal FAQ's with Linn DS/DSM

Qobuz

Qobuz-icon.png
Qobuz
Click for more....
Qobuz-icon.png
Qobuz Streaming CD or Hi-Res quality music
To create and add Qobuz tracks to a Linn DS/DSM playlist you require Kazoo or Linn App
Check for Qobuz FAQ's with LInn DS/DSM

Calm Radio

CalmRadio-Icon.png
Calm Radio
Click for more....
CalmRadio-Icon.png
Calm Radio "Music that helps you get through the day "
To create and add Calm Radio tracks to a Linn DS/DSM playlist you require Kazoo or Linn App
Check Check for Calm Radio FAQ's with Linn DS/DSM

Spotify Connect

Spotify-icon-22.png
Spotify Connect
Click for more....
Spotify-icon-22.png
Spotify Connect can now be used on Linn products using firmware Davaar59 (Aug 2017) or later firmware. (That is, if your Linn DS/DSM has had a software update after Aug 2017 then you can use Spotify connect)
This allows you to select and play your Spotify music on your Linn DS/DSM players and use the internal volume control on the Linn DS/DSM.

To connect your Spotify account to the Linn DS/DSM:
  1. On your control device, iPad/Android/PC/MAC etc, connect to the same computer network as your Linn DS/DSM
  2. Start your Spotify app, (if it is already open then close the App, wait a few seconds, and open the App)
  3. Now check the Spotify Speakers icon to find your Linn DS. (In some cases you may have to power cycle your Linn DS/DSM before this is seen)
  4. Select your Linn product, and you can now play to the Linn DS/DSM from the Spotify account and control the Linn DS/DSM volume.

This is web controlled and if your Linn DS/DSM has already been paired with your Spotify account you will be able to control even if you are not on the same ethernet network.(So be careful that if you accidentally select the Linn DS/DSM as a Spotify speaker and put the volume up high, and you are not at home)

Check FAQ Spotify Connect for more information.

Roon

Roon.png
"Roon Tested"
Click for more....
RoonReadySymbol.png
from Davaar 106 onwards, (March 2024 >), the following products are also Roon Ready and support RAAT audio distribution:


RAAT is also included with Linn DS/DSM's updated to Organik DAC's



Change Roon Protocol to Roon Ready in Manage Systems > Music tab.
Roon RAAT Enable.png
This will also allow you to decide, if the Linn DS/DSM supports has the DACs to support DSD playback, which products decode the DSD. Either Roon decoding or Linn DS/DSM direct playback.



RoonTestedSymbol.png

All Linn DS/DSM ARE ROON CERTIFIED devices

The Linn DS/DSM requires Davaar63 (May 2018) or later firmware to work with Roon V1.5 and above.(That is, if your Linn DS/DS/HUB has had a software update after May 2018 then you can use Roon)


This allows full hi-res audio, (192k/24bit) playback controlled by the Roon system

Songcast is used to share audio between Linn Products when using Roon. It does not use RAAT (Roon Advanced Audio Transport) for sharing Music, so cannot be set up as a Roon-Ready sharer.

Roon Tested Setup
On Linn DS proxy setups, Linn DS with Linn Kontrol preamplifier connected with RS232, the Roon volume control will not control the Linn Kontrol volume.
A Roon Core is required in your network system to allow Roon to control your Linn DS/DSM.
ENABLE the Linn DS/DSM player in the Roon - Settings - Audio - NETWORKED section.
In the Settings > Setup make sure that the Subnet of Linn Streaming is the same as the network that the Linn DS is on. Otherwise, they will not show in the Audio

Control
Primary control is through Roon.
:Transport IR is disabled on the Linn DS/DSM when the Roon input is selected from Linn DS firmware release Davaar80 (Nov 2020)

Issues
Roon uses the Linn DS/DSM as a media player, the control interface IS Roon.

• I cannot see any Linn DS in the Audio list...
If you cannot see any Linn DS product in the Audio list then check that with the setup the correct Linn Streaming subnet (network address range).
E.g. if your Linn DS has IP address 192.168.1.34 then its subnet is 192.168.1.0
Roon-Subnet for Linn.png
• I am only getting Airplay quality audio from the Linn DS using Roon
In Roon: Settings - Audio setup page, you will have devices listed with "via Linn Streaming" and devices listed with "via Airplay".
Pressing this ENABLE button on "via Linn Streaming" will bring this Linn DS player alive.
When you press ENABLE, this will then allow you to rename this Linn DS, otherwise it will be its default name. E.g. below the "Linn Akurate DSM" - "via Linn Streaming" has been enabled and I have renamed it "Merlin Lounge".
Airplay-setup.png


The Linn DS/DSM products have to be declared as "Roon Tested", networked devices in the Roon Core settings. (The "AIRPLAY" option for the Linn DS/DSM must be disabled within the Roon Core).
Roon-Tested-setup.png
Click on the Roon Ready - Enable and give a name to the Linn DS/DSM. (In the example below, this has been named Merlin Lounge)
• I press STOP and the Roon starts playing again...
Transport (play / pause / stop) and Volume can be controlled using Kazoo or Ir handset. Although later versions of Roon will counteract these commands. Only use the Roon controller software to control what is playing.
Linn DS Firmware Davaar80 onwards will disable transport controls whilst on the Roon input of the Linn DS/DSM
• If I select an external source whilst playing Roon, I need to reselect the source to get it playing.
This can be due to a confusion, as the Roon will send a stop command to the Linn DSM as you exit the Roon source. However, as the Linn DSM will probably have changed to this new source, then this new source is stopped by Roon. On external sources, this can only be recovered by selecting another source and going back to the originally selected source.
The solution is to Stop or Pause the Roon source BEFORE you change to a different input on the Selekt DSM.
This can also be reduced by going into Konfig or Manage systems and disabling the "AutoPlay" option.

Deezer

Deezer logo 895px.png


Click for more....
Deezer logo 895px.png
This can now be used on Linn products using firmware Davaar82 (July 2021) or later firmware.
To create and add Deezer tracks to a Linn DS/DSM playlist you require the Linn App
This function is NOT available on the Kazoo or Kinsky Apps
The Deezer is broadcast from the Internet straight to the Linn DS/DSM and you use the Linn App to select and play the Music on the Linn DS/DSM.


Check for Deezer FAQ's with Linn DS/DSM

AIRPLAY

NetAux.png
Airplay
Click for more....
NetAux.png
AirPlay is a Apple protocol that allows wireless streaming media.
The Linn DS/DSM/HUB can take the audio stream via the "Netlink" input.
Check <HERE> for any issues with Airplay


FAQ's

For more common information check


Front display information

Akurate FP display.png

Key points

  • "No Network/LAN" indicates that the Linn DS/DSM/HUB does not have a live computer network connection. This can simply be that the cable is loose or that your computer network/LAN is off/not connected.
  • ! indicates that the Linn DS/DSM/HUB is expecting to see all of the pre-configured Exakt devices, (Exakt speakers, Exakrbox.., Urika-II) connected but it cannot see them. This is typically because the Exakt devices are physically disconnected from the Exakt-link network, they physically have no power going to them or the Linn DS/DSM/HUB has prevously been configured for these products but have not been removed from its setup.



Inputs/Outputs

I have a Akurate DS/DSM and Akurate ExaktBox10 what can I upgrade to Katalyst?

If you are not using the Analogue outputs on Akurate DS/DSM then you only need the upgrade for the Exakt products (Akurate ExaktBox6/10, Akudorik, AkuBariks, Dorik stands).


Note: if you are using an Exakt system, updating the Akurate DS/DSM with Katalyst will make no difference to the audio quality from the ExaktBoxes or Exakt speakers.

For further assistance, try our customer support pages