Selekt DSM FAQ's

From LinnDocs
Jump to: navigation, search


Linn Selekt FAQ's

Top Of Page Index

General operation

How do I find out if my Selekt module(s) have a KATALYST DAC?
Open the KONFIG app:
  1. Select you Linn Selekt DSM,
  2. Click in the "Speakers" tab
  3. Click on the IntegrateQuestion.jpg beside the "integrated" text.
This will show the board information with DAC type and the module type in that slot. As well as the software versions & compilers used within this module:
I have put two or three cartridges in my Selekt DSM and it doesn't work
Update the Selekt DSM to Davaar 69 or higher. This firmware supports multiple cartridge operation
The initial releases the Selekt DSM firmware are only designed to work with one cartridge in slot-1,(closest to the corner). If you add more cartridges (from another Selekt DSM..), or move the cartridge to a different slot then the Selekt will probably not work.

If there is NO HDMI switch board installed then it would appear that only one module is fitted and only allow you to define one pair of speakers. This is because the Selekt will be assign ALL cartridges are Left & Right channels and allowing you to Bi-Amp and Tri-Amp these speakers using all of the module attached. (Do the same check as above, to find out what cartridges are installed)

BEFORE an new Selekt cartridges are installed please ensure that the Selekt DSM is brought up to the latest version of firmware BEFORE fitting these cartridges.

How do I trim the Surround channel levels?

You need to set up the Space Optimistation for you room first. After this is applied you can then trim each channel with the inbuilt noise generator.

Check Volume Equalisation

Top Of Page Index

Music formats

Can the Selekt DSM play DSD music?
  • On initial release with Davaar firmware 65 DSD playback is unsupported. However later versions of Davaar firmware (Davaar 66 onwards, Nov 2018) do support DSD playback.
  • All four playback modules (Line-level/Power Amplifier, Katalyst/non-Katalyst) will support DSD playback with Davaar 66+ firmware
  • USB playback is limited to PCM due to PC/MAC operating system transport.


How can I connect my headphones to the Selekt DSM?
From firware release Davaar 75 (Jan 2020) SPDIF1 can be converted to an SPDIF output that will support up to 192KHz. This will allow you to connect digital headphones to the Selekt DSM. (You may need to change the Selekt Digital output to a fixed sample rate of 88.2k/96k to get Studio Master audio to play on your headphones)
This output is a fixed volume control output, that is, Volume Up/Down had no effect on this output. This will allow you to turn down the speakers, (on Exakt, line or power amplifers modules), and control the volume using your headphone amplifier volume control .

Can I have both a Line level and Power amplifier module in the Linn Selekt?
Yes, when the various modules are released you will be able to mix Line Level and Power Amplifier modules if the correct power supply is installed in the Selekt DSM.
Check that your Selekt DSM has the large power supply fitted, otherwise it will not identify that ANY modules have been fitted. (The small power supply is designed for use with the Line-level modules only. Large power supplies are available as a hardware upgrade)
We would not advise using the Selekt Line-level and Selekt Power Amplifier cartridges for the same audio channels. This is due to the Selekt power amplifier has a lower gain than other Linn amplifiers:
e.g. If you are using the Selekt DSM to Bi-Amp (or Tri-Amp) a pair of speakers and:
  • a Selekt Power Amplifier cartridge to feed one speaker input
  • a Selekt Line level cartridge with external power amplifier to feed another speaker input
This means the Selekt PA fed speaker will be quieter than the external power amplifier fed speaker.

The Linn Konfig app will assume that with different cartridge types you will be using this in a Surround sound system. This will offer the Exakt software configuration upgrade to allow you to configure these cartridge for Surround channels.

  • You may also need a new power supply to deal with the new power requirements.
is the output level of the Selekt DSM different from other Linn DS/DSM's?
The Line RCA output on the Selekt DSM is the same has the same output gain as other Linn DS/DSM products.
However the Power amplifier is approx. 8dB, (8 volume step), quieter than the Chakra amplifiers and ealier Majik DSM's;
Can I add a sub-woofer directly to the Power amplifier outputs on the Selekt DSM?
No,The Selekt DSM power amplifier is a Class-D amplifier and the negative terminal on the power amplifier is NOT connected to earth.
On most sub-woofer "High Level" inputs this is connected to earth and connecting their ground to Selekt DSM negative power amplifier connection may cause damage to both products. Check with the sub-woofer manufacturer on how to connect their sub-woofers to Class-D amplifiers.
Can I connect Electrostatic loudspeakers, such as Martin Logan, to the Selekt DSM?
As the Selekt DSM uses Class-D power amplfiers then the Selekt DSM power amplifier is dependant on the inductive/capative load then the usual loading of Electrostatic loudspeakers may cause poor sounding instability.
Check with your speaker manufacturer for any solutions.
Can I fit another module and have a seperate volume control or a unity gain output?

No, all Selekt modules and Exakt speakers/Exaktbox within the one product share a common volume control.
That is, you CANNOT have different volume controls with ANY single Linn DS/DSM product.

Can I fit another Integrated Amplifier module and Bridge these to increase the Selekt Output power?

No, the Selekt Integrated Amplifiers are already bridged Class-D amplifiers

Is there a TAPE OUT on the Selekt DSM?

No, all Selekt outputs are share the same common Volume control.

I have fitted a HDMI cartridge with Surround module, Can I add a second zone on the Selekt DSM?

With or without the HDMI cartridge the Selekt DSM shares the same volume control to all fitted cartirdges and Exakt products connected to it. Feeding the left and right audio to another room will have a common same volume control with the main Selekt DSM room. (If do wire this up to share to another zone, when you have a surround source playing only the left/right audio is shared with the other zone. The other Surround channels will NOT be shared with this other zone)
You 'CANNOT Songcast this surround audio to another Linn DS. Songcast only supports Stereo audio and will not share any sources that are playing in Surround mode.

How should I set the phono stage input level?
As a general rule of thumb, the phono stage input level should not be less than 4x the specified cartridge output level.
For example, a cartridge with a specified output level of 0.25mV would require a Phono (MC) input setting of 1.2mVrms
If this setting is too low then it can result in audible distortion
If I play a turntable (MM or MC) why do I see "192kHz 24bit PCM" on display ?
All audio that is passed through the Selekt DSM is digitised to allow for Space Optimisation, Songcast to another Linn DS/DSM, Exakt transmission to speakers, etc. The 192kHz, 24bit is the sample rate and bit rate used to convert this into the digital domain.
Note: 192K/24bit is the highest quality audio that the Linn DS/DSM supports.
Can I plug a USB stick into the USB socket of the Selekt DSM

Type: USB-B socket

USB Audio Class 2 endpoint with supported sample rates from 44.1k to 192k

The Linn DSM is a USB stream player. It does not recognise a USB hard drive/USB stick as a Music STREAMING source.

Connect this USB socket into a Windows7/8/10/11 PC or MAC and be a Sound card for these computers.
• DSD audio will typically be transcoded to PCM, by the PC/MAC, before transporting down the USB cable to the Linn DSM
How can I play my Computer Music on the Selekt DSM?
You can connect the Linn Selekt USB socket, (USB Type-B) to connect to your PC/MAC USB socket. You can then set your sound card to output to the Selekt DSM.
On the Selekt DSM, select the "USB" input. On the PC/MAC, click on the Volume icon on the notification bar and select Linn DSM. The audio from your PC/MAC is now directed to the Selekt DSM as a USB Audio Class 2 endpoint

You have two volume controls for this input: one on the PC/MAC and the other on the Linn Selekt DSM. We would advise leaving the PC/MAC volume at 100% and only adjusting the Selekt DSM volume. This will stop any surprises when you change the Selekt DSM to another input such as Radio and suddenly get an extremely loud radio station.
Is there a DIGITAL/SPDIF output?
From firmware release Davaar 75 (Jan 2020), the coxial digital output, SPDIF1 ,can be converted to a coxial digital SPDIF output that will support up to 192KHz.
This is fixed line level with no Space Optimisation.
My Selekt power amplifier is not working?
If you have the Volume control disabled in Konfig or Manage systems, then this will disable the power amplifier on the Selekt DSM.

Selekt display questions

My Selekt DSM has a RED Linn symbol on the dial, what does this mean?
RED-LINN.jpg If you do not have a live network/LAN connection on the Selekt DSM the Linn symbol on the dial will go red.

If your network cable is plugged in and your network/LAN is alive then check that you have the network/LAN cable plugged into the LAN socket (#3 on the back panel diagram) and NOT the Exakt socket (#10 back panel diagram).

WHITE-LINN.jpg After a live network/LAN connection is made the LINN symbol on the dial will turn white after 5-10 seconds.

I get a flashing Linn icon on the volume dial, what does this mean?
This means that the Selekt DSM is in :
  • Searching for Exakt speakers after being woken from Standby (typically only flashes for a couple of seconds after waking from Standby)
  • FALLBACK mode : Fallback is a state that means that the product is waiting for a software update. To stop this flashing either:
  • Power cycle (Switch Mains Off for 10seconds and then switch mains On) and leave the Selekt DSM to startup for approximately 1min.
  • Use the Konfig software to upload software in to the Linn Selekt DSM
Display is showing this icon beside the Volume indicator. What does this mean?
Update Available.jpg Firmware update is available.
The update is not compulsary, just an indication that an update is available.
A Software update is performed by the Konfig software or Linn App. Instructions on how to do this update are listed HERE

Is it normal that the Selekt DSM display cannot always stay on? Can I adjust the display timeout?
We aimed for a display that was unobtrusive when idle. The display automatically activates, drawing the user's attention, when there is a change in DSM state to communicate. E.g. changes to volume, source or track would all cause the display to activate. It is also possible to manually activate the display at any other time by pressing the 'i' (information) button on the handset or by moving towards the Linn DSM, activating its proximity sensor.

The selection of an OLED display helps enable the beautiful appearance of Selekt, where the entire front panel appears as a single uninterrupted expanse. Use of OLED technology does impose some restrictions on use however. Displays will very gradually fade while activated. If any static content is left visible on screen, such as the volume value or source name, this can burn into the display, leaving a shadow of that content constantly visible. Carefully designing a user experience that limits the time that the display is active allows us to achieve a product that is beautiful on the day of purchase and remains beautiful whilst delivering an intuitive user experience over the long lifetime you'd expect from a Linn product.

What does the shimmering dial mean?

This is to show that the Selekt DSM is starting up after a mains power on. It will typically do this for 30-45 seconds, but if the Linn Selekt DSM is performing a software update this may take a little longer.

What does the message "Incompatible hardware" mean?
Incompatible PSU.jpg

You will probably have just fitted an HDMI module to the Linn Selekt DSM. Early Selekt DSMs had power supplies designed to work with specific cartridges only, but as the product has evolved, adding additonal modules may require higher rated power supplies to drive the additional hardware. With the above message, the Selekt DSM has identified that the fitted power supply is not suitable to supply all of the hardware currently fitted to the Selekt DSM and needs to be updated. The power supply is an easily replaced module that can be updated by Linn Retailers.

Note: MCAS 058/059 can be upgraded to SK CPSU1 or SK CPSU2
Please refer to your Linn Retailer to fit the correct power supply.

IP Network

How do I find the IP address of my Selekt DSM?
When the front panel display is asleep, looking on the top of the Selekt DSM:
  1. Press the UPPER part of the dial. The front panel display will now show System options.
  2. Press the LOWER part of the dial to highlight "PROPERTIES"
  3. Press the RIGHT part of the dial to select this option.
This Selekt display will now show the Selekt Properties and IP Address.
The above action can also be performed using the Linn IR handset joystick controls.

Reseting the Selekt DSM

How do I do a FACTORY reset on the Selekt DSM?
You will need to have the Konfig running to do the Factory Reset, plus internet access for the Selekt DSM
This will do a reset all setting to default setting. This action may take a short time, typically 60seconds, to perform this action.
  1. Make sure that your Selekt DSM is powered on and your LAN network has Ethernet access
  2. In Konfig go into the Advanced and find your Selekt DSM
  3. Press the RESTORE and leave it to do the update.
  4. After approx 60seconds your Selekt DSM will have been set back to Factory setting.
  5. All Done
How do I RECOVER on the Selekt DSM?
You will need to have the Konfig running to do the full RECOVER, plus internet access for the Selekt DSM
This will do a fresh reload of Software and reset all setting to default setting. This action may take some time to perform as it need to download new software packages and install them. Typically this maycan take one hour to perform.(The is dependant on your Internet speed and how many software versions need to be installed).
  1. Make sure that your Selekt DSM is powered on and your LAN network has Ethernet access
  2. In Konfig, go into the Advanced and find your Selekt DSM
    1. If you cannot see you Selekt DSM double check the power connections and network connection.
    2. if you still don't have the Selket DSM listed in Konfig press the FALLBACK ( #2 in the image below) and repeat checking Konfig>Advanced tab
Power Amp Selekt backpanel.jpg
  1. Press the RECOVER and leave it to do the update.
  2. After approx 60minutes go to the Selekt and using the Dial what Software Version is installed.
  3. All Done

General Linn DS/DSM/HUB Wifi Wifi.png

The Wifi module used with the Linn DS/DSM/HUB supports IEEE 802.11a/b/g/n/ac PSK/CCMP 1-CH

this supports both 2.4G & 5G communications.

Wifi History


This was the first Wifi defined in 1997, 802.11b, generally used with 11, or 13 channels depending on your country. Each channel could each supply a data rate of 11MBit/s .
This data rate was then expanded to 54MBit/s in 2003, with the 802.11g. However, this still used 2.4G and instead of using 1channel to communicate it now uses 3-channels to communicate.This reduced your number of usable channels as other device communicating on a channel next door would now encroach into your channel(s).
This means that 2.4G band can have a lot of noise and interference. Coupled with fact that this same frequncy is used by DECT phones, Microwave ovens, Baby mointors, Taxi Radio, Bluetooth.... These can inject a lot if noise and interfere with Wifi streaming link to the Linn DS/DSM/HUB as it may force the LInn product off the Wifi network and it will have to retry the connection, this takes time and may cause your Linn product to keeping muting the Music


A newer standard, 802.11n, allows usage of both 2.4G and 5G to give an even bigger data rate of up to 600Mbit/s.
As standards improve the 802.11ac that the Linn DSM/Series3 supports is a data rato of up to 1,300MBit/s.
5GHz is a much cleaner radio space with a lot less interence compare with 2.4G. The only negative is a slightly reduced range.
Some Wireless-Access-Points, WAPs and Router allow you to setup a seperate SSID, (Service Set IDintifier. this is name for a Wi-Fi network.)

Advice on use

We recommend that you configure your Wifi network to have seperate SSID for 2.4G and a different SSID for 5G wifi. Then configure the Linn DSM/Series-3 to only use the 5G network.
This will then allow the music stream to work on a cleaner transport/Wifi and stop any device from interfering with the music that you are listening to.

There are Apps available to show you what is on your Wifi and your network

Disable Wifi

To totally disable the Wifi, go into the Konfig:About tab and disable the Wi-Fi option.

  • NOTE: In the Konfig:WIFI tab, setting to NONE will only disconnect it from any Wifi network. The DSM will still broadcast its presence on the Wifi network.

Wired LAN connections

If you have connected a LAN cable to your Linn DS/DSM/HUB/SERIES3 then this take priority over the Wifi connection. This means that the Wifi connection is still on but ignored when a there is a live connection on the products LAN socket. When the LAN connection is removed then the connection returns to Wifi.

Common FAQ's

Top Of Page Index

Music formats

What audio formats do the DS players support?
DS products support
  • FLAC Up to 192k 24bit
  • WAV
  • AIFF
  • AIFC
  • MP3
  • AAC
  • WMA (lossy)
  • ALAC (Apple Lossless) upto 192K 24bit (If these ALAC files were generated by an early version of dBpowerAmp the Linn DS will not recognise these. Transcode these files to ALAC using the latest version of dBPowerAmp to fix this.)
  • DSD - limited to some products in a certain configuration. Check DSD Support for more informaiton

Linn recommends FLAC.
DRM protected files cannot be played on the DS products

Why does Linn recommend FLAC?
  1. FLAC is a free open format. It is non-proprietary, which means your music collection is safeguarded for the future, can be played through any open digital music player, and is not tied to a particular manufacturer or product. The specification is published for all to see. In contrast, SACD has failed to achieve significant success because it requires proprietary music content and disc players with proprietary hardware inside.
  2. FLAC allows even better than CD quality encoding and decoding. Linn Records provides studio master quality downloads in FLAC, at the same quality as SACD.
  3. FLAC supports metadata, or tags, so that useful information about a piece of music can be stored with the music; for example, album, artist, genre, cover art, sleeve notes, etc. User interfaces can make good use of these tags. Two examples of applications that support tag editing are: Mp3tag (Windows) and Tag (Mac)
  4. Because it is open and free, there are an extensive set of players, tools, transcoders (to convert between other formats and FLAC), tag editors, and other programs for FLAC.

Can the Linn DS/DSM play DSD music?
Products that will play DSD audio
  • Linn DS/DSM players with Katalyst DAC's, from firmware Davaar 60, can play DSD audio files. This is performed by passing the native DSD stream directly to the Katalyst DAC and letting the DAC do the processing and volume control.
  • All ORGANIK DAC's fitted within the Linn DSM can play DSD audio files.
  • New Klimax DSM (2020 variant)
  • Selekt DSM both "Standard" and "Katalyst" DAC's

Some important points on DSD playback on the Linn DS/DSM:

  • The DSD audio is ONLY available on the Linn DS/DSM analogue outputs.
The DSD audio stream is NOT supported on:

  • Exakt-link to Exakt speakers or Exaktbox. That is, DSD files will NOT play on Exakt speakers or Exaktboxes.
  • Digital outputs. (TOSLINK, SPDIF)
  • Songcast to other Linn DS/DSM players

  • Supports DSD64 (2.8224MHz) and DSD128 (5.6448MHz) sample rates.DSD256 is only supported on Klimax DSM (2020 variant).
These in the following formats:
  • DSF - Sony format that supports ID3 tags
  • DFF - old Philips mastering format (aka DSDIFF)

  • DSD is NOT supported on external inputs such as Toslink or USB


  • No digital signal processing is possible. This means:
    • No balance control is possible to DSD audio file playback.
    • No Space Optimisation is applied to DSD audio file playback
    • Maximum volume is restricted to 80 (unity gain) on DSD audio file playback. However if you have raised to volume to a higher level e.g. 90, this higher volume is applied to any tracks that are NOT DSD audio files.

Linn Kazoo Server supports the index and serving of DSD files. Non-indexed DFF files that have no metadata can be browsed by file name using the Kazoo Server Removable drives option.
Asset UPnP server and Minimserver support DSD index and serving to the Linn DS/DSM.

Can I change the audio quality of the Radio

NO, the Linn DS/DSM.HUB only plays the Radio stream provided by Tunein.

Does the Linn DS/DSM players play BBC Radio via TuneIn?

Yes, the Linn DS/DSM/HUB will continue to use TuneIn to access and play the BBC radio stations.
From the 30th September 2019 BBC radio made changes to what can access their Radio stations via TuneIn. This is mainly for devices that can support using the BBC Sounds App. The Linn DS products do not support the Sounds App can will continue to have BBC Radio playback rights using Tunein.
Check the BBC Sounds >HELP< section for more information.

How do I add BBC Radio stations to my Presets?

  1. Select the TuneIn button in Kazoo /Linn App and find the BBC, or any other Radio station you wish to add in selection tree
  2. Press the three dots on the right hand side of the station and enable/disable the Favourite, (TuneIn > Favourite in Linn App).
  3. Complete

I cannot get any foreign Radio stations, I can only get UK stations

Due to a legal case between TuneIn and Sony Music, Warner Music. on licences. UK radio stations have licences for UK wecasting. However, non-UK based radio stations were not licensed to webcast music within the UK,
This is a TuneIn issue we are waiting for them to resolve. The alternative is to configure the Linn DS/DSM with airable internet radio

Does the Linn DS/DSM players play MQA?
No, check this link "MQA is bad for Music" for more information
Can the DS player play multi-channel files?
No, the Klimax DS, Akurate DS, Majik DS, Majik DSI, Sneaky Music DS, Sekrit DS, Sneaky DSM, Sekrit DSM and Sekrit DSi are stereo audio only.

Klimax DSM, Akurate DSM & Majik DSM can play multi-channel audio from their HDMI inputs if they are using Davaar55 or later software.

Upgrading software

How do I upload new software into the Linn DS/DSM
  1. First of all you need a PC or MAC and install the KONFIG app.
  2. After you have installed KONFIG go to the ADVANCED tab. If your Linn DS/DSM requires an update it will be listed here.
  3. If an update is available for that Linn DS/DSM then press the UPDATE' button

More detailed instructions are listed HERE

Physical Input/Outputs

How do I add Music to play on Linn DS
If your Music is on a CD then this must be RIPPED from the CD first.

This can be using a PC or MAC with CD-ROM drive or from a Network attached Storage device/NAS with inbuilt ripper.
If you are using a PC or MAC you can use software listed HERE
The "Ripped" Music can be held on the PC/MAC of on a Network attached Storage device/NAS. The NAS is the better option as this is a low power device that can be left on all of the time.
The PC/MAC/NAS requires UPnP Media Server software to share the Music for the Linn DS/DSM to play.

Will downloaded music play on the DS players?
Yes, so long as it is not protected by Digital Rights Managemant (DRM) restrictions and is in one of the supported formats, or transcoded to such a format.
Can I Airplay from my Android device?
Without ROOTING the android device there is no way to stream to the Linn DS (Airplay AOA Service).
All other apps take the media file and stream it via UPnP.
Streaming local files can be done use Skifta and “Double Twist Player”
Media Applications

After Updating to Davaar55 I can only get audio from my Exakt outputs and not the Analogue Out
Check Konfig > Device > "Dual Analogue/Exakt Stereo Output" has been enabled.
If you have declared your Exakt speakers as 'Front Left'/'Front Right' and the analogue outputs to be 'Front Left'/'Front Right' (Stereo). ensure that this option in Konfig is enabled. The audio in the Exakt outputs will be out of sync by approx 45mS compared to the analogue outputs.

Are the Digital outputs (Toslink/SPDIF) volume controlled?
No, the digital outputs are ALWAYS full line level outputs. They are not Volume controlled or Mute-able from the standard Linn DS/DSM controls.
The Digital outputs will always produce the front Left & Right of the audio source that is playing on the Analogue or Exakt outputs.

General Q's

Can I stop the kids from playing with the front panel buttons?
Yes on of the Majik & Akurate DS/DSM/HUB. If you go into Konfig > Display settings you can define "Front Panel buttons" to be OFF. This will stop the front panel buttons from doing anything. You can still control the Linn DS/DSM by IR handset and the Kazoo App.
(Just remember if you have disabled the front panel buttons and think that the Linn DS/DSM is broken!)

How do I achieve gapless playback for live albums?
To guarantee gapless playback, you will need to rip your music tracks into a lossless format (i.e. FLAC). You must also ensure that you are using ripping software that does not add gaps between tracks when ripping (i.e. DBPoweramp). Most ripping software will offer the option to turn this feature off.
Also make that that you have selected the PLAYLIST input and NOT the UPnPAV input


What is a PIN, check HERE for more detailed information.


  • We currently support pinning from Kazoo Server (V4.9.8 onwards) , Tidal, Qobuz, TuneIn, CalmRadio, DS radio presets, and Linn DSM external inputs
  • This is only applicable with Linn DS/DSM players with Davaar 64 or higher firmware
  • This currently does NOT support Pins to external pre-amplifier inputs, such as Akurate Kontrol, Kisto etc.
  • PINs use discrete IR codes and are not used with any other Linn Product control.
  • PINS for Radio stations are wrongly created with Kazoo V4.13.21, this has been fixed with next version 4.13.22. If you have created a Radio station PIN and it doesn't work, check you have a later version of Kazoo and re-assign this PIN to the correct radio station.

Deezer on the Linn DS/DSM

Deezer logo 895px.png
This can now be used on Linn products using firmware Davaar82 (July 2021) or later firmware.
To create and add Deezer tracks to a Linn DS/DSM playlist you require the Linn App
This function is NOT available on the Kazoo or Kinsky Apps
The Deezer is broadcast from the Internet straight to the Linn DS/DSM and you use the Linn App to select and play the Music on the Linn DS/DSM.

Check for Deezer FAQ's with Linn DS/DSM

Linn Songcast

Songcast is the method of transport for streaming STEREO audio data between a Songcast sender, (Linn DS/DSM, Songcast App), and Songcast receivers, (other Linn DS/DSM players listening to that sender DS - multiroom operation.)
The Songcast stream contains the raw unprocessed music stream, the metadata information for the Music playing and timing information.
  • The raw music data is the same data as received by the sending Linn DS. This maintains the same music stream is processed by ALL Linn DS players, (sender and receivers).
    • As this Songcast music stream is untouched this leaves the receiving Linn DS/DSM to do its own volume control.
    • Volume, Space Optimisation and Exakt processing, if used, are all performed as a final process to minimise any digital processing.
  • The timing information is used to ensure that the Linn DS/DSM players are in sync with the music sender.

There is a ! on the front panel of my Linn DS/DSM

There is a speaker setup issue on the Linn DS/DSM Surround Sound Rules

The front panel of the DS is showing a flashing dot or lightening flash and I cannot see the Linn DS with Kazoo or Konfig

This is the Linn DS either in "startup" mode or in "Waiting for Software" mode.

"Startup": The flashing dot is the startup mode trying to connect to you ethernet network. This mode will typically occur when you first apply power to the Linn DS/DSM. This will typically take 30seconds and go into standard use mode.

"Waiting for Software": The lightening flash is the Linn DS/DSM waiting or getting a software update.

If you have any problems getting the Linn DS on an Ethernet network, (dot continuously flashing), try the following options:- Option1

  • Power off the EVERYTHING connected to the Ethernet system, (PC, Printers, DS, Routers/DHCP servers).
  • Leave everything powered off for at least 10seconds.
  • Switch everything back on.
  • Retry the system

You will find that some of the devices in the system get confused and cause system confusion. The power cycling will do a reset of the system and recover most issues.


  • Use fresh Ethernet cables, (replace existing cables).
  • If the Linn Ds is more than 3M (10ft) from the DHCP/Server. Move the Linn DS right beside the Router/DHCP server and patch using a short Ethernet cable (1M), the Linn DS to the DHCP server/Router
  • Retry the system


  • Build a totally separate system with only a DHCP/Server and Linn DS.
  • Retry the system

Some networks only have a limited number of DHCP address’s. if you have already connected some PC’s to this system, your Router/DHCP server can remember these devices, (even though no longer connected) and will not allocated these previously assigned IP addresses to newly connected products. So the case of unplugging one device to free up an IP address for the DS to use will NOT work with most Routers/DHCP servers if there are no free DHCP IP addresses available.

This will give a better idea as to what is causing the problem. (98% of the time, this is due to a local network issue).

If you always get the flashing dot then the lightening flash symbol then the Linn DS/DSM needs to be programmed. Check the Konfig Manual > Updates section or contact your Linn Retailer to get assistance.

FAQ on ALL products link

Top Of Page Index
Click HERE for FAQ on ALL products