REM 022

Operation with Linn DS/DSM

The following functionality is available on Linn DSM devices with Infra-Red (IR) control. If IR is not currently enabled on the Linn DSM then this can be done via Linn Konfig.

This IR handset can be used with ALL Linn DS/DSM products. Some functionality is configured by Linn Konfig (IR commands accepted) & Kazoo App (PINS).

To Enable IR

• Open Konfig
• Select the Linn DS/DSM
• Select the Configuration tab
• Set Handset Commands Accepted to All or CD depending on user requirement

Basic Functions

1. SLEEP - Will put the unit into / out of Sleep mode.
2. NUMERICAL KEYS - Numerical input.
3. ★ - Reserved for future use
4. SHUFFLE - press to toggle Shuffle state

   - Press and hold for 2 seconds for HELP information (Davaar 69 onwards),

   Subsequent SHUFFLE key presses will you more HELP information:

   --e.g. Software update, IP address, MAC etc.

5. NAVIGATION / SELECT - Up / down / left /right / enter keys for navigation.

   ON Linn DSM products with the top dial, this has the same function as the dial operation.

   e.g.

   • Left and right keys
   • Up and down keys
   • Select/OK button.

6. PINS - For switching between PINS, these buttons will work with any Linn DS/DSM running Davaar 64 or higher.
7. TRANSPORT CONTROLS - Play, pause, skip forward, skip back.

   • Press and hold pause will stop playback

8. MUTE - To mute / unmute volume.
9. VOLUME + , - - Volume + , -.
10. SOURCE + , - - Source + , -.
11. INFORMATION - changes information displayed on the DSM

    front panel

• Press and release - toggles different display modes e.g. track

number, bit rate etc

• Press and hold - scrolls the current track playing

PINS

Requirement: Davaar64 on Linn DS/DSM and minimum Kazoo 4.13

A PIN is the physical selection of six buttons on the top facia of the following Linn products:

▼ PIN   Klimax DSM /3 (2020 Variant)   Majik DSM /4 (2020 Variant)   Selekt DSM /0   Selekt DSM /1 Classic Hub   Selekt DSM /1 Edition Hub   Series 3

Each PIN can be assigned/programmed by using Linn App, Kazoo to a saved Playlist, local source, Radio preset... to allow a quick and simple selection of your favourite music

The PIN service has been extended to all Linn DS/DSM products via the control software. Such as Linn App, Kazoo PC or MAC, Kazoo - Android devices, Crestron, Control4 & Savant.

More and more media attachment options are being added with software improvements, so watch this space.

(Pressing two PIN buttons at the same time can also be used in the setup of the relevent product. Check the relevant product page for more information)

PIN FAQs:

• We currently support pinning from Kazoo Server (V4.9.8 onwards) , Tidal, Qobuz, TuneIn, CalmRadio, DS radio presets, and Linn DSM external inputs

• This is only applicable with Linn DS/DSM players with Davaar 64 or higher firmware

• This currently does NOT support Pins to external pre-amplifier inputs, such as Akurate Kontrol, Kisto etc.

• PINs use discrete IR codes and are not used with any other Linn Product control.

• PINS for Radio stations are wrongly created with Kazoo V4.13.21, this has been fixed with next version 4.13.22. If you have created a Radio station PIN and it doesn't work, check you have a later version of Kazoo and re-assign this PIN to the correct radio station.

FAQ: IR Handset

• Can the REM 020 or REM 022 IR handset be used to control other/earlier Linn Product?/
  

These IR handsets will have limited control of

* Pre-amplifiers, (Kairn, Wakonda, Akurate Kontrol, Unidisk..) has Volume, Mute, Source+/-, (no direct source selection) and Standby (if applicable).

* CD/DVD players, (Unidisk, Karik, Ikemi...) has basik transport (Play, Pause, Skip track +/-), track number selection, joystick, (if applicable) and Standby, (if applicable).

* Radio, (Kudos, Kremlin..), no functionality

The handsets use the Remote codes developed by Philips, called the "RC5 protocol". This protocol is also used by other Manufacturers such as Loewe, Arcam etc, so this handset may control the other manufacturers products and vice-versa.
If this cause any problems then we suggest with the Linn DS/DSM, or other manufacturers products, that the IR control is disabled. (At least with the Linn DS/DSM you also have Tablet and PC/MAC control using our control software Apps