Klimax DSM (Exakt Variant)

From LinnDocs
Revision as of 11:09, 14 August 2019 by Yoda (talk | contribs) (Latest software)
Jump to: navigation, search
KlimaDS 3Q 02 low res.jpg

Getting Started

www.linn.co.uk/go/klimax

Product info

  • Product Name: Klimax DSM/1 (2014 Variant)
Other variants of this product can be found at Klimax DSM Variants
  • Date of Introduction:June 2014 - Sept 2016
Replaced by Klimax DSM/2 in 2016


Hardware Upgrades

HDMI 2.0 Upgrade
Linn Surround Module for bitstream Surround sound decoding


Note: It should be noted that information may at times be out of date and should not be used as a current list of what upgrades are available.'

Support

Linn Support Site

Latest software

Latest software releases

Details of latest Product release software

Manuals

Quickstart Guide

Using the Linn DS/DSM/HUB with IR handset, PC, MAC, Android tablet, iPad/iPhone...
Remote Control manual
Manage Systems manual
Space Optimisation (Advanced)
Surround Sound with Exakt systems
Safety Information
Warranty Terms and Conditions
Third Party Software Copyright

Network Setup

DS Budget System Setup

DS Entry Level System Setup

DS High End System Setup

Back Panel Connections

Image:Kli DSM 1 rear.jpg


  1. MAINS INPUT - To connect to the mains electricity supply.
  2. TOSLINK IN- To connect sources with Toslink (optical) digital outputs.
  3. ETHERNET - To connect to a network (100Base-T)
  4. SPDIF IN - To connect sources with Spdif digital outputs.
  5. EXAKT LINK - To connect to Exakt compatible devices (Exaktbox, Exakt Speakers, Urika II etc)
  6. EARTH GROUND - For connecting the unit to an earthing terminal if no mains earth is available or for joining the earths of other products in the system to improve perfromance in areas of poor/noisy electrical earth conditions.
  7. BALANCED IN RIGHT, LEFT - To connect sources with balanced (XLR) outputs. 1 2 (input transformer can be by-passed using Konfig)
  8. BALANCED OUT RIGHT, LEFT - To connect to a preamplifier (or power amplifier when internal volume control is enabled) with balanced (XLR) analogue inputs.2
  9. UNBALANCED OUT RIGHT, LEFT - To connect to a preamplifier (or power amplifier when internal volume control is enabled) with unbalanced (RCA) analogue inputs.2
  10. HDMI OUT - To connect to a display device with HDMI inputs.
  11. HDMI IN 1, 2, 3 - To connect sources with HDMI outputs.
  12. FALLBACK - To put the device into Fallback mode (used when reprogramming)



1 XLR to RCA adaptors are supplied for connecting sources with unbalanced outputs.
Input transformer can be enabled or disabled in Konfig setup
Note: Configuring to RCA will add a ground link to the audio tranformer causing an imbalance in the HOT and COLD XLR connections

2 Set to DELAY mode > DIRECT to pass through an Analogue volume control to the Analogue out.
Only use the XLR(8) output OR the RCA(9) output, never use both outputs as the RCA will degrade the XLR(8) output audio.

EXAKT LINK connection

Check HERE for information of Exakt link connection


Kli DSM 1 rear differences.jpg


Klimax DSM/1 differences


Changes to Klimax DSM/1 compared to the Klimax DSM/0

  1. - 2off Exakt link sockets - To connect speakers/Tuneboxes with Exakt Link. This will allow audio from both the Analogue output and Exakt outputs.
  2. - 1off SPDIF input - The Klimax DSM/0 has 2off SPDIF inputs



Front Panel

Image:Klimax_DSM_front.jpg


  1. DISPLAY
  2. ON / OFF SWITCH


Installation

Please read the following carefully before installing the unit in your system – your unit may need to be reconfigured by your Linn retailer.

Exakt Options

Exakt usage the the Exakt Klimax speakers can be found at Klimax Exakt System

Check Exakt trouble shooting if you have any issues with the Exakt system.


FAQ's

Check:


For further assistance, try our customer support pages