Difference between revisions of "Template:Info:Linn Surround Module"
m (→Linn Surround Module) |
m (→Linn Surround Module) |
||
| Line 8: | Line 8: | ||
:*Dolby Digital Plus, | :*Dolby Digital Plus, | ||
:*Dolby TrueHD, | :*Dolby TrueHD, | ||
| − | :*DTS, DTS-HD Master Audio, | + | :*DTS, |
| − | :*DTS-HD. <br> | + | :*DTS-HD Master Audio, |
| + | :*DTS-HD, | ||
| + | :*DTS Neo:6.... | ||
| + | <br> | ||
:Dolby Atmos and DTS-X are not supported. | :Dolby Atmos and DTS-X are not supported. | ||
| Line 24: | Line 27: | ||
Space Optimization will be supported for this configuration, but not Space Optimisation+ (for Exakt speakers).<br> | Space Optimization will be supported for this configuration, but not Space Optimisation+ (for Exakt speakers).<br> | ||
{{Info:LinnSurroundModule-Channels}} | {{Info:LinnSurroundModule-Channels}} | ||
| + | Some information for setup in Konfig [[Konfig_Manual#Surround_sound|<u> can be found HERE</u>]] | ||
Revision as of 14:36, 13 February 2019
Linn Surround Module
Direct decoding of surround streams from HDMI / HDMI-ARC / TOSLINK / SPDIF is supported with the addition of a Linn Surround module mounted onto the HDMI-2 board within the DSM.
The Linn Surround module is sold only as an upgrade to any:
List of products that support the surround upgrade module
- Selekt Products
- All variants of Selekt DSM (upgraded with Selekt HDMI switching module)
- Akurate Products
- Akurate DSM (Exakt variant) (upgraded with HDMI-2 board)
- Akurate DSM (4K compatible)
- Akurate DSM (Katalyst variant)
- Akurate Exakt DSM (upgraded with HDMI-2 board)
- Akurate Exakt DSM (4K compatible)
- Akurate System Hub
- Klimax Products
- The HDMI-2 boards have been fitted as standard since September 2016 and are available as an upgrade to all Akurate and Klimax DSM's.
Sneaky/Sekrit/Kiko & Majik Products
This Linn Surround Module upgrade is either not available or is not supported in these products.
- Supported codecs on HDMI, HDMI-ARC, TOSLINK and SPDIF connections
- Dolby Digital,
- Dolby Digital Plus,
- Dolby TrueHD,
- DTS,
- DTS-HD Master Audio,
- DTS-HD,
- DTS Neo:6....
- Dolby Atmos and DTS-X are not supported.
- Available from the Konfig > Dolby/DTS tab are Neo:6 mode selection, and ‘Dynamic Range Compression’ (formerly known as Midnight Movie Mode on earlier Linn products).
- Speaker positioning should be achieved through Space Optimisation, however if Space Optimisation is disabled, the speaker distances may be configured from the Konfig > Dolby/DTS tab.
Speaker configurations:
To reduce the Exakt hardware requirements for extra channels, it is possible to configure an ExaktBox or ExaktBox-I to drive one non-Exakt speaker per channel, up to a maximum of 8 channels, using either a 6 x channel passthrough or 8 x channel passthrough Exakt filter.
Space Optimization will be supported for this configuration, but not Space Optimisation+ (for Exakt speakers).
- Speakers can be driven from any combination of:
- Direct analogue output from the DSM
- Exakt Speaker
- Exaktbox configured with crossovers for one or two speakers
- Exaktbox configured for surround playback
- Speaker type set for
- 6 x Channel Passthrough for 5.1ch or
- 8 x Channel Passthrough or 7.1ch
- Speaker type set for
- Examples of speaker setups can be found HERE
Some information for setup in Konfig can be found HERE
Setup via IR handset:
- Use the left/right handset joystick control to adjust the Lipsync. (make sure that in Konfid the "delay mode" for that source is set for "Video Sync"
- Press the Up/Down buttons to adjust the LFE (sub-woofer) settings.
