Difference between revisions of "Template:Info:Linn Surround Module"

From LinnDocs
Jump to: navigation, search
m (Linn Surround Module)
m (Linn Surround Module)
Line 8: Line 8:
 
:*Dolby Digital Plus,
 
:*Dolby Digital Plus,
 
:*Dolby TrueHD,
 
:*Dolby TrueHD,
:*DTS, DTS-HD Master Audio,  
+
:*DTS,  
:*DTS-HD. <br>
+
:*DTS-HD Master Audio,  
 +
:*DTS-HD,
 +
:*DTS Neo:6....
 +
<br>
 
:Dolby Atmos and DTS-X are not supported.
 
:Dolby Atmos and DTS-X are not supported.
  
Line 24: Line 27:
 
Space Optimization will be supported for this configuration, but not Space Optimisation+ (for Exakt speakers).<br>
 
Space Optimization will be supported for this configuration, but not Space Optimisation+ (for Exakt speakers).<br>
 
{{Info:LinnSurroundModule-Channels}}
 
{{Info:LinnSurroundModule-Channels}}
 +
Some information for setup in Konfig [[Konfig_Manual#Surround_sound|<u> can be found HERE</u>]]
  
  

Revision as of 14:36, 13 February 2019

Linn Surround Module

Direct decoding of surround streams from HDMI / HDMI-ARC / TOSLINK / SPDIF is supported with the addition of a Linn Surround module mounted onto the HDMI-2 board within the DSM.

The Linn Surround module is sold only as an upgrade to any:

Selekt or Akurate or Klimax DSM


List of products that support the surround upgrade module

Selekt Products
Akurate Products
Klimax Products


  • The HDMI-2 boards have been fitted as standard since September 2016 and are available as an upgrade to all Akurate and Klimax DSM's.


Sneaky/Sekrit/Kiko & Majik Products
This Linn Surround Module upgrade is either not available or is not supported in these products.

  • Supported codecs on HDMI, HDMI-ARC, TOSLINK and SPDIF connections
  • Dolby Digital,
  • Dolby Digital Plus,
  • Dolby TrueHD,
  • DTS,
  • DTS-HD Master Audio,
  • DTS-HD,
  • DTS Neo:6....


Dolby Atmos and DTS-X are not supported.


  • Available from the Konfig > Dolby/DTS tab are Neo:6 mode selection, and ‘Dynamic Range Compression’ (formerly known as Midnight Movie Mode on earlier Linn products).


  • Speaker positioning should be achieved through Space Optimisation, however if Space Optimisation is disabled, the speaker distances may be configured from the Konfig > Dolby/DTS tab.


Speaker configurations:
To reduce the Exakt hardware requirements for extra channels, it is possible to configure an ExaktBox or ExaktBox-I to drive one non-Exakt speaker per channel, up to a maximum of 8 channels, using either a 6 x channel passthrough or 8 x channel passthrough Exakt filter.
Space Optimization will be supported for this configuration, but not Space Optimisation+ (for Exakt speakers).

  • Speakers can be driven from any combination of:
  • Direct analogue output from the DSM
  • Exakt Speaker
  • Exaktbox configured with crossovers for one or two speakers
  • Exaktbox configured for surround playback
Speaker type set for
6 x Channel Passthrough for 5.1ch or
8 x Channel Passthrough or 7.1ch
Examples of speaker setups can be found HERE


Some information for setup in Konfig can be found HERE


Setup via IR handset:

  • Use the left/right handset joystick control to adjust the Lipsync. (make sure that in Konfid the "delay mode" for that source is set for "Video Sync"
  • Press the Up/Down buttons to adjust the LFE (sub-woofer) settings.