Template:Info:Linn DSM Player Connections

From LinnDocs
Revision as of 11:54, 6 December 2018 by Yoda (talk | contribs)
Jump to: navigation, search

Linn DSI/DSM connections

Linn Products Inputs (L+R) Outputs (L+R) Comms
Phono /RCA XLR Tos -link8 SP DIF8 3.5 mm jack HDMI Phono /RCA1 XLR XLR1 ExaKt12 Tos -link9 SP DIF9 Head phone HDMI Analog Record Speaker (W-RMS)2 RS232 (Proxy) RC5 Acc5
Kiko 1 0 1 1 1 3off HMDI 1.3 0 0 0 0 0 1 1 0 2x 50W3 0 0
Sneaky DSM 1 0 1 1 0 3off HMDI 1.3 1 0 0 0 0 0 1 0 2x33W or 4x33W7 0 0
Sekrit DS-I 1 0 1 1 0 0 1 0 0 0 0 0 0 0 2x 70W 1 1
Sekrit DSM 1 0 1 1 0 3off HMDI 1.3 1 0 0 0 0 0 1 0 2X50W or 4x33W4 0 1
Majik DSI/DSM (Non HDMI) 46 0 3 3 1 0 1 0 0 1 1 1 0 1 2x 90W 1 0
Majik DSM (HDMI) 4off HDMI 1.4 1 0 0
Majik DSM/2 111 2
Majik DSM/3 4off HDMI 2.0 1 + ARC
Selekt DSM 2xLine 1xMC 1xMM 0 2 2/1 13 0 0  ?14  ?14 2 0 0/113 0 ARC ONLY 0  ?14 0 0
Akurate DSM 26 1 3 3 1 4off HDMI 1.4 1 1 0 1 1 1 1 0 0 0 0
Akurate Exakt DSM 0 0 4 0
Akurate DSM/1 1 1 1
Akurate DSM/2 4off HDMI 2.0 1 + ARC
Akurate Exakt DSM/1 0 0 0
Akurate DSM/3 1 1 1
Klimax DSM 0 1 2 2 0 3off HDMI 1.4 Either RCA or XLR 0 0 0 0 1 0 0 0 0
Klimax DSM/1 1 2
Klimax DSM/2 1/013 3off HDMI 2.0 1/013 1 + ARC
Klimax Exakt DSM 1 2 3off HDMI 1.4 0 4 0 1
Klimax Exakt DSM/1 3off HDMI 1.4 1 + ARC
Klimax System HUB

Note:
1 All these Analogue outputs are Line level or Volume control with the Konfig - Volume Control option
2 Output is either volume controlled or OFF
3 Kiko has Aktiv speaker output, this is a separate power amplifier per speaker drive (2off driver units per Kiko speaker) giving a total of 50W per channel
4 The Sekrit DSM can be configured as bridge or single ended. This can drive, in stereo with common volume control, either 4off speakers with 33W/4R RMS power each or 2off speakers with 50W/8R RMS each.
5 For use with Basik3/Basik3-IR Room Control Units
6 One input can be configured for use with Turntable.

Line Level / Moving Magnet [Majik-factory set] / Moving Coil (Akurate-Factory set]) refer to dealer for options

7 The Sneaky DSM can be only configured as single ended. This can drive, in stereo with common volume control, either 4off speakers with 33W RMS power each,(for Bi-Amping), or 2off speakers with 33W RMS each.
8 Maximum input sample rate 96KHz (Stereo PCM)
9 Maximum output sample rate 192KHz (Stereo PCM)(However the official specification for TOSLINK/SPDIF is 96kHz so check your digital receiver can take up to 192K data stream)
11 PRE-OUT can be make POWER Amplfier input for use as additional amplifier for ExaktBoxes. Konfigurable in Konfig
12 Exakt-Link

  • Exakt-Link output are delayed by approx 45mS compared to Analogue/Toslink/SPDIF outputs.
  • When the volume control is disabled, the Exakt-link sockets are disabled
  • Exakt-Link can also be used as an input with products such as the Urika II

13 Can be configured in Konfig application to change the Default SPDIF Input a SPDIF output
14 This can change depending on the Module(s) installed in the Selekt DSM