Difference between revisions of "Troubleshooting"

From LinnDocs
Jump to: navigation, search
(KAZOO User interface issues)
(QOBUZ not streaming Hi-Res quality)
Line 102: Line 102:
  
  
==QOBUZ not streaming Hi-Res quality==
+
==QOBUZ streaming issues==
 +
===QOBUZ not streaming Hi-Res quality===
 
The quality of the Music streamed is governed by Qobuz depending on the Account that you have with Qobuz.
 
The quality of the Music streamed is governed by Qobuz depending on the Account that you have with Qobuz.
 
'''Hi-Res music''' Qobuz will only work if you have a '''SUBLIME HIFI''' account and have already purchased this Hi-Res Music. <br>
 
'''Hi-Res music''' Qobuz will only work if you have a '''SUBLIME HIFI''' account and have already purchased this Hi-Res Music. <br>
Line 108: Line 109:
 
'''MP3 quality music''' if you only have '''Basic''' account or '''Premium''' account this will stream at MP3 quality.<br>
 
'''MP3 quality music''' if you only have '''Basic''' account or '''Premium''' account this will stream at MP3 quality.<br>
 
<br><br>
 
<br><br>
 +
==QOBUZ show me tracks but I cannot play them, the PLAY/SKIP button is greyed out==
 +
QOBUZ media is licensed. This means that some the Music you have selected in not available for streaming to your country.<br>
 +
You may have purchased the Music and downloaded this Music from Qobuz but this is not licensed for streaming.
  
 
==Internet Radio & Tidal keep dropping out==
 
==Internet Radio & Tidal keep dropping out==

Revision as of 09:11, 22 October 2015

Contents

Some information can also be found in the FAQs section

KAZOO User interface issues

iPad

If you are only getting a black screen do a hard reset of the iPad:
Press and HOLD BOTH the POWER button and the HOME button until the Apple icon appears
If you have previously done a software update without fully shutting down the previous version of teh Kazoo app (double press the HOME button, select the Kazoo app and slide up to quit), then the original version of the Kazoo app may be running in background while you are trying to run the new version. The hard reset will normally fix this black screen.

Twonky Media & iPad

If you are using iPad and the Music cannot be added to the Playlist, but if you go to a PC/Mac and this does allow the same Music you will probably also using Twonkymedia.
The solution is to go in the Twonky Settings > Advanced > Media receivers and RESET LIST. Now retry the iPad Kazoo and it will probably now work.

Windows PC

There have been reports that Kazoo keeps freezing/hanging and to get control back you have to quit Kazoo and restart it. This is because Windows is putting the network connection into sleep mode without telling Kazoo and causing poor communication.
  • One way to stop this is to go into Device Manager (right click the Windows icon),
  • Click on the “Network Adaptors”,
  • then the “Power Management” tab and DISABLE the “Allow computer to turn off this device to save power”

Kinsky issues

Any knowns issues with each version of Kinsky is reported in
iPad Kinsky
iPhone Kinsky
Windows Kinsky
MAC OSX Kinsky


Konfig diagnostics

Konfig 10 Issues Get a copy of the Log file:

Windows Vista & Windows 7:

Using the Computer/File Manager (Windows Explorer):
1. Go to the menu item 'Tools -> Folder Options...' (You can press <ALT> T for this)
a) Go into the 'View' tab
b) In 'Hidden Files and Folders' enable the 'Show Hidden files, folders and drives'
c) OK that options page
2. Go into C:\Users\username\AppData\local\Konfig and forward a copy of the UserLog.txt to the helpline@linn.co.uk helpdisk. (Change the username to your username on the PC)

MAC OSX

Using Finder
1. Go - Go to Folder
a) ~/Library/Konfig
b) and forward a copy of the UserLog.txt to the helpline@linn.co.uk helpdesk

After forwarding a copy of the Userlog.txt Install the earlier version of Konfig for [PC version] [MAC OSX version

Then update your DS/DSM before using Konfig 10

Songcast

Songcast issues

SongBox

Songbox

General operation Fault finding

This to help with the basic fault finding of a Linn DS system.


Exakt system doesn't work

Check Exakt troubling shooting section

Majik/Akurate/Klimax DSM has no audio on HDMI or HDMI Rear channels

This is a known bug with Davaar19 if you have Startup Mode- "Active"
Go into Konfig and change this to Startup Mode- "Sleep" will always give HDMI audio
If the Linn DSM is setup for surround mode then we have found that this also causes an issue with no rear channels if the Startup mode is Active. As a temporary solution until Davaar20 is release, change the startup mode to Sleep


Tidal streaming issues

Setting up a Tidal account, I get an error “Sorry, no flowId is set up…”.

Either the Tidal service or Linn’s voucher codes are not yet supported in the user’s country. User should contact support@tidalhifi.com for more details

In Kazoo UI the login screen icon just keeps spinning

Try power cycling the Linn DS/DSM then reselecting the Tidal box in Kazoo UI
If you are using a BT Home hub5 check that Smart Setup is turned OFF

Kazoo UI does not show the Tidal option

Check that you are using Kazoo UI V4.3.653 or higher. Check, via Konfig, that the Playlist source is visible.

On Kazoo UI a red message stating "Connection failed"

This can be the Linn DS may not have internet access or the Tidel Music server is offline.

  1. If you are using a BT Home hub5 check that Smart Setup is turned OFF
  2. On the Linn DS select the Radio input and check that you can get internet Radio from this input. This will tell you if your DS has internet access.
  3. Try power cycling the Linn DS/DSM then retry selecting Tidal Music selection.

If points 1 or 2 do not make any difference please contact support@tidalhifi.com

Music from Tidal is dropping out

Music from Tidal is CD quality, audio drop out can be caused by your internet/broadband struggling with the high bandwidth data/Music stream, (especially during holiday period, or certain times of the day the internet can be very busy with kids games, iTunes streaming, Businesses, etc within your local area, (or household)).

Tidal is a brand new service so some drop-outs may be caused by teething problems with their servers, so please be patient.

By default the Linn DS/DSM gets CD quality audio from Tidal. If the drop out are frequent you can

  1. Go into Konfig > Your DS/DSM > Tidal and
  2. change the Audio Quality from “Lossless(FLAC)” to “High (AAC 320K)” or “Low (AAC 96k)”.

This will allow you to listen to Tidal Radio until your internet/broadband can cope with the higher data rates. (This Audio quality is changed when the next track starts)


QOBUZ streaming issues

QOBUZ not streaming Hi-Res quality

The quality of the Music streamed is governed by Qobuz depending on the Account that you have with Qobuz. Hi-Res music Qobuz will only work if you have a SUBLIME HIFI account and have already purchased this Hi-Res Music.
CD quality music if you only have HIFI account or HIFI Classic account
MP3 quality music if you only have Basic account or Premium account this will stream at MP3 quality.


QOBUZ show me tracks but I cannot play them, the PLAY/SKIP button is greyed out

QOBUZ media is licensed. This means that some the Music you have selected in not available for streaming to your country.
You may have purchased the Music and downloaded this Music from Qobuz but this is not licensed for streaming.

Internet Radio & Tidal keep dropping out

This can be down to your broadband link. Most domestic broadband can be of a high speed, 100MHz. But the ISP does not give a minimum guaranteed speed per second only a maximum speed per second. This may give priority broadband to Business customers in your area. (Especially on a Monday morning)
This minimum speed may not be sufficient to provide enough of a radio 'stream' and can cause dropouts/muting.
Upgrading to a Business broadband, (normally only a small cost), guaranteeing a minimum of 100kbps will normally reduce/eliminate the dropouts muting.

iPad/iPhone or Android keeps losing the Linn DS/DSM or Airplay keeps dropping out

This can be a common problem if the Wifi communications to temperamental. The commands from the iPad/Android are sent but lost because communications noise.
You may think that your Wifi is good as it works OK with the internet but this is not the case. (You have have to double click some pages to get them to show, this can be due to poor wifi or some pages are slow in loading, this can be due to poor communications)

REASONS FOR INTERMITTENT OPERATION

Apple devices Wifi settings

require the Wifi to be set-up to a specific configuration or it will otherwise start looking for a Wifi signal that does support this configuration Check Here for details of what to check or iOS and OS X: Recommended settings for Wi-Fi routers and access points]

Wifi noise

This noise can be generated by Microwave ovens, DECT phones, wireless Video repeater, Taxi Radios, neighbours Wifi etc. so we would suggest checking this with wifi scanner software such as Insidder this can be used to find out who else is broadcast on the same channel are your Wifi and causing interference.
This allows you to check your Router/WAP Wifi settings and move them to a cleaner channel. There are two frequencies in use with Wifi, these are 2.4GHz and 5GHz. the 2.4GHz is the typical frequency used, the 5GHz is fairly new so check that your iPad/Android can support this bandwisth before using it.

If you have DECT phones make sure that they are not close (>2M) to your Router or Wifi devices

Routers / Wireless Access Points

Some Routers/WAP devices are very poor with UPnP control, namely Sky and BT. If you have one of these Routers we would suggest adding 'Subnet' Router of one that Linn has tried and works reliably.

App check

Other apps running in your iPad/iPhone can cause some issues. Try restarting your iPad/Android and use Kinsky before starting any other apps. This will tell you if any other App is causing a problem.

Apple Music will not play on my Linn DS

Apple Music can be downloaded on to your PC/MAC/Apple device for playback.
However, this music is DRM'd to ONLY for playback on Apple device. The only way to play this music is to purchase it from iTunes and download it ready for Media serving to the Linn DS.
To listen to Apple Music on your Linn DS with Airplay from you PC/MAC/iDevice or play it on iTunes and Songcast it to the Linn DS

HDMI general Troubleshooting

The Linn DSM products provide HDMI pass through of HDMI V1.4 signals

The Linn DSM products HDMI output will:-
1. Pass-throu the HDMI audio when the Linn DSM is in Standby.
2. Pass-throu the HDMI audio when the Linn DSM is listening to an Analogue or Digital Audio input.
3. BLOCK the HDMI audio to the TV if the the DSM is listening to a HDMI input.

ARC - Audio Return Channel

Due to difference in Manufacturers implementation of ARC, the Linn DSM does not support this function

I cannot get any picture through the HDMI

General connections

The Linn DSM does not support 4k resolution

Playstation3

The Playstation3 is known to have HDMI connection issues with many non-Linn devices.

  1. Select PS3 input on the Linn DSM
  2. While the PLAYSTATION 3 system is in standby mode (red light on the front of the system), hold down the touch-sensitive power button on the front of the system until the system goes into standby mode again . (So the light cycle would go from: red light --> green light --> then back to red light). This will ensure that you have held down the power button long enough to reset the Video Output Settings.

Check PS3 FAQ's

Apple MacMini, MacBook Pro etc

If you switch the DSM to the HDMI feed from a MacMini, MacBook etc, it will initially loose any picture and audio, this may take up to 30seconds to appear and for the Audio to return. This delay is due to the Mac performing HDMI communication and re-establishing the audio and video options.

HDMI connection with Video scalers

If you have a video scaler in the HDMI chain and you are not getting any picture through the Linn DSM, take the video scaler out of the system to see if the picture returns.

No Audio playback on HDMI connection

The Linn DSM will ONLY support 2ch (or multichannel) PCM audio, it does not support Dolby Digital, DTS etc. If you feed an unsupported audio from your DVD player/Sat Receiver etc the Linn DSM can pass though to the TV if the DS is in Standby mode but when you select that input on the DSM there is no audio then double check that the audio out on the DVD/Sat is configured for 2ch PCM.

Check Linn forum link

Fritzboz not seeing the Linn DS/DSM products

Fritzbox  reported having issues with Apple broadcasts and losing connections. 
This appear to be due to the Fritzbox monitoring the LAN sockets and shutting down
anything that is not active and going into Green (power saving) mode.
The manufacturer has reported the following fix:
1. Open a web browser and enter "fritz.box" into the address bar to open the router's
   configuration page
2. Go in to advanced/expert mode, rather than Wizard mode
3. Go to the "System > Energy Monitor > Settings" pane
4. Set the LAN port that the DS is plugged into to be "always active"
5. Click the "Apply" button
click to enlarge



















I cannot get album cover art on Kinsky

Please Refer to Troubleshooting in the respective Kinsky manual

Kinsky will not play any of the tracks from the Folder view

If the Music files directly using the Kinsky Folder option:

  1. Make sure that these Music files have some sort of tagging
  2. Check the Music files are in a SHARED FOLDER
  3. Ensure (with Windows Vista/7/8) that the Network is a Home/Work or Domain type, NOT a Public Network.
  4. Re-start your computer just in case some other software is blocking this operation.

I cannot play some of my iTunes tracks on the DS

If you Music resides in the iCloud (iTunes Match) and NOT not located on your PC then this Music CANNOT be played on the Linn DS, (The DS does not have access to the iCloud)

When I select the Linn DS on my Linn PreAmp the volume options disappears

This is due to the name on the wrong DS name listed in the Preamplifer source name. (If you have change the name of the DS or performed a software update this will/may happen)

To fix this,

  • Go in to Konfig
  • Select your Linn PreAmplifier
  • Click on Configuration
  • Go to Sources and expand (click on the > beside Sources)
  • Expand the input that the Linn DS is connected to
  • click on the 'Name' and you see a drop-down arrow appear at the right hand side of the name box
  • Select the name of the DS displayed.
  • Click on another box in Konfig and the change has been made.
  • Check operation with Kinsky.

iPad/iPhone cannot see any DS or Library

First try and do a hard reset of your iPhone/iPad, Press AND HOLD both the HOME key and the power button until the Apple symbol appears on the iPhone/iPad display. then retry Kinksy

Wifi Setting check

If you still have issues it has been found that updates to the Apple operating system (IOS 5.1.0) have been found to cause wireless communications issues for any Apple software. We have found that your Wifi device should be setup with

* WPA2 Personal for Wireless authentication
* AES : Wireless encryption
* if your WAP supports 'n' channel then set the bandwidth to 20MHz
* 'Forget the Network' On your iPad, then re-attach it after power cycling the Wifi device (WAP)

This should improve all communications to your i-device Apple link Apple link 2

Apple iDevice are not very good at roaming. What this means is if you have Wifi transmitters it will hold on to it last one until the signal is below 1%. SO you could be right beside the other Wifi transmitter and having issues as the iDevice is still connected to the one furthest away. try switching you Wifi Off (or use Flight mode), wait a few seconds and switch on Wifi, this will hopefully jump to the stronger signal.

Check the Router settings

It has been reported that Routers with QOS enables will cause problems. Disable QOS on the Router to see if this improves communications Apple link 3

Check Internet connections

IOS6 appears to check if there is internet access, if it cannot find internet access it will start searching for a WiFI connection with Internet. This jumping around Wifi connections can cause poor communication with the Kinsky software. On the iPad/iPhone turn ON flight mode, then re-enable the Wifi connection. This will stop the iPad/iPhone from searching for Internet access. (This does not affect Browser access to the internet on the iPad/iPhone, only stops the iPad/iPhone for check for software updates)

Using SongCast on my PC/MAC, the music keeps dropping out

This is due to the music data not getting to the Linn DS player fast enough.

Solution1: Go into the the PC/MAC Songcast Advanced preferences and increase the Latency value, (suggest doing it at 100mS steps, try it and if the Music drop out occurs again, increase the Latency by another 100mS, repeat until the drop outs stop.

Solution2: If you are using a Wifi link this may be a weak signal (and reducing the bandwidth) or there is another Wifi device broadcasting on the same channel. Either change the Wifi Channel, get a stronger Wireless Access Point or use a wired netwrok conneciton.

After power cut I cannot see my Linn DS/DSM in Kinsky

On switch on the Linn DS/DSM will check in the first few seconds with there is a computer network to connect to. If it doesn't find this ethernet network is will continue its start-up (bootup) thinking that there is never going to be network available and totally ignore any communications via ethernet. It will allow you to change inputs and volume using the IR handset and front panel but nothing else. (most DHCP servers can take 30-90 seconds before they produce a live network link)

The only way to recover from this is to make sure that there is a live network connection going the the DS (lights flashing on the network socket) and power the Linn DS/DSM off then one again.
If you have frequent power cuts we would suggest either:-

  1. An Uninterruptible Power Supply (UPS) on the DHCP server/Router to keep it alive during power cuts. or
  2. Add an Ethernet Switch between the DHCP Server/Router and Linn DS/DSM. The Switch will normally be alive in the first second of power up. The Linn DS/DSM will then, a few seconds later, see that there is a live network and keep asking for an IP address, (consistant flashing dot).

Note: If you want to know the IP address of the Linn DS/DSM then press and HOLD the # button on the new Linn handset (the 'Info' button on the older handsets), this will initially show you the IP address.
If this address is 127.0.0.1 this is a 'null' IP address and the DS has not seen a network during its startup. Any other number means it has seen the network and should be seen by Kinsky

Net-Aux input is not auto switching

The Net-Aux is designed to accept third-party Music streams. If, within Konfig, the Net-Aux input is declared as "Visible - No", then the Linn DS/DSM will automatically switch to that input when a Stream is sent to it.

If, within Konfig, the Net-Aux input is declared as "Visible - Yes", then you have to manually switch to this input to start playing the third party audio stream.

This option will allow the user stop any third party streams from stealing the DS and allow full user control of the Linn DS/DSM from its control device(s)

Check the Konfig Manual

I cannot see my DS in the Songcast Preferences tab

Press the REFRESH button, if your Linn DS('s) do not appear:- 1. Check the Advanced TAB - Network settings that the correct Network connection is used 2. On Konfig, check under Sources, that the Songcast<Songcast> source is Visible 3. Press the REFRESH button

Check the Konfig Manual


The Linn DS/DSI will only play one track then stop

Make sure that the Linn DS/DSI has the PLAYLIST source selected, NOT the UPnPAV source. The UPnPAV source is available for standard UPnP control devices that do not have the facilty to save the Playlists on the Linn DS itself.


I seem to be getting more music drop-out since changing to Davaar

Audio drop-out on the Linn DS/DSI is caused by the Linn DS/DSI waiting for the streamed data. The Linn DS/DSI has a limited buffer memory to allow small music stream breaks but if the incoming music stream is lost for too long or is not fast enough to feed all of the music stream required for real-time playback, this causes the Linn DS/DSI to MUTE until the the buffer memory is full and can carry on playing again.
With Davaar software there has been no change in the amount of data streamed from your music storage device to the DS, with a very marginal increase in the outgoing network traffic from the Linn DS/DSI to support the Songcast feature. These drop-outs are more likely to be due to media server changes (after a software update, internal maintainance or data corruption in the NAS) or other devices on the network taking up network bandwidth.
We suggest disconnecting any other Ethernet devices not required for the Linn DS/DSI to NAS connection to help track down the cause of music drop-outs. This may mean trying out a Linn tested DHCP/Server with a different UPnP media server (PC instead of NAS running the required software). This will help track down the cause of the ethernet music stream drop-outs.

CANNOT get BBC Radio

BBC is presently changing its broadcast format. Some ISP's can broadcast this, some cannot, plus the BBC are having some other difficulties. check BBC & BBC Multicast

Cannot see the NAS in Kinsky/Konfig or shortcuts disappear

Suspect that your PC is running Norton 360. Follow the following link for instructions on how to get this working


ALAC files cannot be played on the Linn DS/DSI player

If the ALAC files have been created with a early version of dBpowerAmp or iTunes, these Music files may not be played by the Linn DS/DSI. To recify this, we suggest using dBPowerAmp V14 and above and transcode these from ALAC to ALAC, this will correct the file issue

Internet Radio keeps muting

This is due to breaks in the media stream from the Internet.

This can be due to high network traffic in your area, business first thing monday morning, or heavy useage of video broadcast (like footbal matches).

Some ISP's will also reduce your bandwidth of certain types of network traffic, typically Bittorrant (P2P). Some ISP's will mistake your Radio stream for a Bittorrant and throttle this network traffic and cause muting of your Internet Radio.

Most domestic broadband states am "up to" bts speed of you broadband but does not state a minimum connection speed.(If you do a quick speed test will appear to be OK (this is a burst of datat). But the internet Radio is a constant stream of data. Any long breaks/delays in this stream can cause the internet Radio to mute)
If you upgrade to a Business broadband (typically only a small amount extra), these will state a MINIMUM broadband bps. So if your area has difficulty in Internet Radio, suggest trying a upgrading your broadband to a Business broadband with a minimum speed of 500kbps, this should reduce/eliminate your internet Radio muting.

I cannot see any AIFF Metadata

TwonkyMedia does not support the AIFF Metadata. Twonky have been asked to add this (May 2nd 2012) [1]

Windows Home Server (RipNAS) has audio drop outs

This may be due to the WHS housekeeping check [2]

Since installing CARA6, I cannot see the DS using Kinsky

As Cara6 has an internet Radio function, it will check the internet for any updates in the Tunein Radio (previously RadioTime) login etc.

If you have a poor or no broadband/internet link, this can cause the DS to appear to be invisible on Kinsky Desktop whilst it is searching for the TuneIn website.

If you leave the DS alone for approximately 3 minutes it will start working as it realises the lack of the Internet.


When playing WMA lossless files, the DS will play the track for so long, then give a white noise (like the sound of waves crashing)

CARA6 does not support WMA lossless Music files. It may appear to play some of the files OK, but others can cause the DS to play Music then give a white noise hiss.


Problems updating the Linn DS software.

There may be issues with your network.

  • Restart your network by power cycling the components, starting with the DHCP server/router, then the Linn DS, then the PC.
  • Try updating the software again.


If you still have problems

  • Bring the Linn DS, PC and DHCP server/router to the same location and use short patch leads (<3M, 10ft)
  • Power cycle these products starting with the DHCP server/router, then the Linn DS, then the PC
  • Try updating the software again.


Finally if you still have problems, (this should be done by a Linn Retailer).

Procedure for manual update


Where can I get help on Kinsky / Konfig / Jukebox Software?

Kinsky manual is here.

Jukebox manual is here.

Konfig manual is here.

The front panel of the DS is showing a flashing dot and I cannot see the Linn DS with Kinsky or Konfig.

Computer networks can get very fussy. If you have any problems getting the Linn DS on an Ethernet network, (dot continuously flashing), try the following options:-
Option1

  1. Power off the EVERYTHING connected to the Ethernet system, (PC, Printers, DS, Routers/DHCP servers).
  2. Leave everything powered off for at least 10seconds.
  3. Switch everything back on.
  4. Retry the system

You will find that some of the devices in the system get confused and cause system confusion. The power cycling will do a reset of the system and recover most issues.

Option2

  1. Use fresh Ethernet cables, (replace existing cables).
  2. If the Linn Ds is more than 3M (10ft) from the DHCP/Server. Move the Linn DS right beside the Router/DHCP server and patch using a short Ethernet cable (1M), the Linn DS to the DHCP server/Router
  3. Retry the system

Option3

  1. Build a totally separate system with only a DHCP/Server and Linn DS.
  2. Retry the system

Some networks only have a limited number of DHCP address’s. if you have already connected some PC’s to this system, your Router/DHCP server can remember these devices, (even though no longer connected) and will not allocated these previously assigned IP addresses to newly connected products. So the case of unplugging one device to free up an IP address for the DS to use will NOT work with most Routers/DHCP servers if there are no free DHCP IP addresses available.

This will give a better idea as to what is causing the problem. (98% of the time, this is due to a local network issue).

I cannot find TWONKY V4.4.* to run the Linn DS products.

If you are running on a Netgear ReadyNAS we recommend that you use the Netgear Forum version of Twonly 5.0.68. See Linn Forum for instrucitons


Twonky have recently changed their website. You can download Twonky from
[ http://www.twonkyforum.com/viewtopic.php?f=2&t=7653 ]


ReadyNAS - Twonky 4.4.17 ot Twonky 5.0.68 (Netgear version)

Note: you buy the Twonky Media SERVER licence, NOT the Twonky Media MANAGER licence.


the Media Server Licence can be purchased from Buy Twonky Service


I cannot see the Linn DS on my control point

If the control point cannot see the DS product, check the following:

1. If your PC has multiple network connections, (wired and wireless-WifI). Disable one of them so you are ONLY using wired ethernet or wireless ethernet. Restart the control and check operation.

2. Some Network DHCP servers/switches can block UPnP communication. Either check the router settings or use a ethernet router such as the Netgear RP614 to see if this cures the issue.

3. You may have different Anti-Virus & firewall packages from the Windows default, (such as Norton, McAfee, etc) ensure that these have the above files with exceptions as per their Manual, plus check the UPnP port. [3]

4. Try another control point, to check the operation of your PC

I can only see some of my Music and the Music keeps pausing

If you are using TwonkyMedia, suspect that the Music Rescan time is too small. The rescan action can take several minutes (>30minutes in large file collections. If you set the Rescan time to be too small, it will start performing another  Rescan before it has finished the first etc, etc, etc.

Ideally the RESCAN time should be set to "0" (zero) and you can create an Internet Desktop shortcut for the URL:

http://your_NAS_IP:8100/rpc/rescan for Netgear ReadyNAS or

http://your_IP:9100/rpc/recan for most other devices

This will tell twonky to only rescan when you have added something new.

Linn Forum reference

If you are running DS with CARA1 software, update to CARA2 firmware. This is performed by running the KONFIG application and select the Update tab, select CARA2 and press the UPDATE button. Complete



I cannot play some of my iTunes files

Downloaded iTune Music is DRM protected, (Digital Rights Management). This will ONLY allow playback on iTunes devices.

These Music files will have the M4P extension. To make these files visible to the DS, the DRM must be stripped off these Music files. (This may be done by iTunes or illegal software).

Contact iTunes on the supply of non-DRM files.


A ripped CD is not showing up

Firstly, ensure that the CD has been ripped to the correct location (e.g. to the NAS and not to the PC).

If that is not the cause, it is possible that the metadata is incorrectly applied, or there is no metadata. Tools like Audioshell, which runs as part of Windows Explorer, will show the file properties including the track metadata.

Metadata is a place holder for the track/album/artist information. It can hold much more info, but it is this minimum information that is required by the media server to enable it to find an album and tracks.

In some cases, the FLAC metadata may be incorrectly applied. One common problem is that FLAC files are wrapped in ID3 tags instead of using the standard FLAC/Vorbis tagging. FLAC with ID3 tags is against the FLAC specification, and early versions of DS players reject these files as invalid. When viewing the metadata from MP3Tag ID3 tags will be shown as "FLAC (FLAC ID3V2)" instead of "FLAC (FLAC)". If this has happened the tag data can be removed using MP3Tag, but you will then have to re-add the correct metadata manually using the same tool. Usually, it will be faster to rip the disc again, but before you do so, ensure the ripping software is correctly configured.


Archive