Sekrit DSM

From LinnDocs
Revision as of 10:54, 17 August 2022 by Yoda (talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search
SekritDsm.png

Product info

  • Product Name: Sekrit DSM (2012 / 2018 Variant)
  • Date of Introduction: December 2012 - February 2022
  • Type: Integrated digital music player, pre-amplifier, and power amplifier
  • Dimensions: 345 mm (width) x 44 mm (height) x 196.5mm (depth)

Support

Linn Support Site

Latest software

Latest software releases

Details of latest Product release software

Manuals

Konfig manual

Kazoo User Guide

DSM Remote control manual

Space Optimisation

Safety Information

Warranty Terms and Conditions

Third Party Software Copyright

Audio Latency

DSM Audio Latencies Explained


Back Panel Connections

SekritDsmRear 2.jpg
  1. MAINS INPUT - To connect to the mains electricity supply.
  2. FALLBACK - To put the device into Fallback mode (used when reprogramming)
  3. ETHERNET - To connect to a network (100Base-T)
  4. HDMI OUTPUT - To connect to a display device with HDMI 1.4 inputs.
  5. HDMI INPUTS - To connect sources with HDMI 1.4 outputs.
  6. ANALOGUE OUTPUT (RCA, variable/fixed level) - To connect to subwoofer (note:when the internal volume control is disabled, this will also disable the internal Power amplifier/speaker outputs) with unbalanced (RCA) analogue inputs.
  7. IR OUTPUTS - To connect to infrared flasher devices allowing control of other products that accept infra-red signals.
  8. DIGITAL INPUT (Toslink) - To connect sources with Toslink (optical) digital outputs.
  9. DIGITAL INPUT (Spdif) - To connect sources with Spdif (RCA) digital outputs.
  10. ANALOGUE INPUT (line level) - To connect a turntable or line level source with unbalanced (RCA) outputs.
  11. SPEAKER OUTPUTS - To connect to loudspeakers, Neutrik 4 pole connector
  12. RC5 ACCESSORY - To connect Linn BASIK3 or BASIK3-IR Room Control units, (setup for RoomAmp2 connection (jumper link removed)). Standard IR receivers cannot be used in this socket. This requires a Knekt-CAT-5 cable to connect to the Linn DSM


Front Panel Connections

SekritDsmFront 3.jpg
  1. IR SENSOR - Recieves IR commands
  2. DIAGNOSTIC LEDS - See table below for functionality
  3. FALLBACK - To put the device into Fallback mode (used when reprogramming) (F-BACK)
  4. POWER SWITCH- Switches the power on/off
  5. IR REPEATER CLAMP- IR Repeater Clamp fixing screws


DIAGNOSTIC LED FUNCTIONS

Text

ON

indicates

OFF

indicates

Slow Flash / Blink

Fast Flash

IR Pulse on IR command received Reserved for future use Reserved for future use n/a
AMP Internal amplifier enabled Internal amplifier disabled Internal amplifier fault n/a
AUDIO Valid audio (digital inputs only) n/a Invalid audio (digital inputs only) n/a
IP DHCP IP address obtained Default IP address obtained n/a n/a
NET Ethernet link established no link established n/a n/a
STBY Device in standby Device active Searching for IP address (boot) Fallback (reprogramme)



Speaker Wiring

The Sekrit DSM has 4 DAC channels and 4 Power Amplifiers. These amplifiers can be configured in single ended mode or bridged mode. All speaker outputs (and Analogue Output) share the same common Volume control.

Connections to the speakers are made via Neutrik Speakon connectors, NL4FX. Neutrik Speakon Assembly Instructions

The single ended mode is best suited to bi-amping a pair of passive speakers or for driving multiple pairs of loadspeakers. Bridged mode is best suited to driving a single pair of loudspeakers.

The wiring details are shown below:

SekritDsmWiring.jpg


  • 33W/channel in single-ended mode
  • 50W/channel in bridged mode



Installation

Please read the following carefully before installing the unit in your system – your unit may need to be reconfigured by your Linn retailer.



FAQ's

Check:


For further assistance, try our customer support pages