Difference between revisions of "360 pwab /Setup"
m |
m (→LED Status) |
||
Line 93: | Line 93: | ||
=== LED Status === | === LED Status === | ||
[[File:360_Diffuser.png|300px|right|link=]] | [[File:360_Diffuser.png|300px|right|link=]] | ||
− | + | <br> | |
+ | <b>Front panel</b> - Light in the stand "Dispersion Window" immediatley below the loudspeaker. | ||
{| border="1" cellspacing="0" cellpadding="0" width="65%" align="LEFT" | {| border="1" cellspacing="0" cellpadding="0" width="65%" align="LEFT" |
Revision as of 15:05, 27 November 2023
Linn 360 (Passive With Aktiv Bass Setup)
Contents
Manuals
Installation
We recommend that your 360 loudspeakers are unpacked, installed and adjusted by an authorised Linn retailer. To get the best from your 360 loudspeakers, it is important that they are positioned and levelled correctly.
Please note, in order to achieve the very best from your 360's, some adjustment may be required after positioning, levelling and connecting.
Unpacking
IMPORTANT:
The 360 speakers are heavy; take great care when moving them.
When unpacking, lifting or moving them, we recommend using two people to avoid personal injury.
- Do NOT lift your speaker using the amplifier module, this will cause damage to your loudspeaker.
- Do NOT lay the loudspeakers on their front face or the amplifier on the rear as this will damage the loudspeaker.
- Do NOT lay the loudspeakers, in any orientation, without the transit bolts in place. This would risk damage to both the cabinet and the module isolation mounts.
- We recommend that you retain the packaging in case you need to transport your loudspeaker(s) at a later date.
- Loudspeakers are packed individually, with a separate package containing both speaker stands.
- Take care when unpacking to avoid damage to the cabinets and drive units.
- Note the important Safety information on the Beryllium Dome Tweeter
- Double check that the transit screws have been removed
-
Positioning
As with any stereo loudspeaker, there are some fundamental principles which should be observed to get the best sound from your loudspeakers.
- The loudspeakers should be place at an equal distance from the wall behind the loudspeakers.
- The speakers should be a similar (not the same) distance from the walls to the outside of each loudspeaker.
- Any toe-in applied should be the same for each loudspeaker.
- The loudspeakers should be level with all four spikes in contact with the floor. Use Linn Skeets for hard floors.
For further assistance, try our customer support pages.
Levelling
![Adjust Spikes.jpg](/wiki/images/thumb/a/ac/Adjust_Spikes.jpg/100px-Adjust_Spikes.jpg)
Screw the spikes into the corners of the stand.
Fit the lock nuts, but do not tighten at this stage.
![Level 350 spkrs.jpg](/wiki/images/0/05/Level_350_spkrs.jpg)
Very carefully (do not scratch the cabinet), use a spirit level to check if it is sitting
level. If it is, gently rock the loudspeaker from front to back, side to side and
diagonally to check for any movement. If none is present and the loudspeaker is
sitting level, no adjustment to the spikes is necessary.
If the loudspeaker is not level, or moves when you rock it, loosen the appropriate lock nuts using the tool provided and use a screwdriver to turn the spikes to adjust their height. Adjust the spikes to level the speaker, using a spirit level placed on the stand.
Press down firmly on the top of the loudspeaker to ensure it is in close contact with the flooring.
![Tighten spikes.jpg](/wiki/images/thumb/0/0c/Tighten_spikes.jpg/114px-Tighten_spikes.jpg)
Use the spirit level as before and continue to adjust the spikes as required.
Once the speaker is level and does not rock, use the screwdriver to hold the spike in place and fit and tighten the lock nuts with the spanner provided.
Note: To protect wooden or tiled floors, the spikes can be placed on Linn Skeets, which are available from your Linn retailer.
Connections & operation
Back Panel
![360 pwab backpanel.png](/wiki/images/thumb/f/fb/360_pwab_backpanel.png/275px-360_pwab_backpanel.png)
- MAINS INPUT - To connect to the mains electricity supply.
- POWER SWITCH - To connect sources with phono outputs.
- BALANCED INPUT'(XLR-Line level)
- GAIN 1 - Adjust the Bass gain to match the external amplifiers used.
- FEED 2 - To define if Bass amplifier feed from XLR or speaker terminals
- UPPER BASS - 4 mm terminals for upper Bass drive unit.
- MID - 4 mm terminals for mid-range drive unit.
- TWEETER - 4 mm terminals for treble drive unit
- Removable plate 3 - Covering Exakt sockets
Notes:
- 1: ONLY for XLR Feed 2 Power DAC gain to match the level of the bass system with your choice of power amplifier. Linn power amplifiers have a gain of 27 dB, 0 GAIN.
- 2 To select the Power DAC feed:
- ‘INT’ – Input feed from the speaker terminals. (If you don’t have a suitable line-level output).
- ‘XLR’ – Input feed from the line-level XLR input. (Best sound quality option).
- When using XLR you should ensure the bass amplifier gain is matched to your power amplifiers, 1
- 3 Exakt sockets ONLY for use with externally Aktiv configuration with ExaktBox(s) or Software update.
- These sockets play NO part in music playback in Passive With Aktiv Bass (PWAB) mode/
Passive example1:
- Power DAC FEED from Internal feed
- This will extract the Power DAC feed from the 360 speaker 4 mm banana sockets and attenuate the signal to feed the Power DAC
![360 pwab passive wiring.png](/wiki/images/thumb/8/8a/360_pwab_passive_wiring.png/700px-360_pwab_passive_wiring.png)
Passive example2:
- With Power DAC FEED from XLR sockets
- In this setup, the Line level audio to fed directly to the Power DAC. This is the better sounding configuration.
![360 pwab passive wiring XLR.png](/wiki/images/thumb/6/6a/360_pwab_passive_wiring_XLR.png/700px-360_pwab_passive_wiring_XLR.png)
Externally Aktiv additional connections
- Remove plate, #9 above, to show the Exakt connections.
- After being converted into an external aktiv setup, by an experienced Linn Retailer, the 360 loudspeaker MUST connected to the Exakt-link circuit for setup and operation.
![360 pwab Exakt backpanel.png](/wiki/images/f/f8/360_pwab_Exakt_backpanel.png)
- EXAKT LINK - From Exakt Master OR from an Exakt Slave connected to the Exakt master
- SERVICE - For use of Linn Technicians only
- FALLBACK - Primarily for Linn service use only, to put the device into Fallback mode (used when reprogramming the unit).
Note: The LED behind the Fallback indicates the Exakt Link is active, but the product is not powered/switched off. - EXAKT LINK - To Exakt Slave product
- STATUS INDICATORS - Function of the LEDs are given below:
Externally example:
- Externally Aktiv sample wiring using a Klimax DSM, a Klimax Exaktbox, six Klimax Solos amplifiers and a pair of 360 PWAB loudspeakers
- Note how the Exakt wiring goes to all Exakt products, including the 360 loudspeakers
![360 pwab Extrenally Aktiv wiring.png](/wiki/images/thumb/a/a2/360_pwab_Extrenally_Aktiv_wiring.png/1000px-360_pwab_Extrenally_Aktiv_wiring.png)
EXAKT LINK connection
Check HERE for information of Exakt link connection
LED Status
![360 Diffuser.png](/wiki/images/thumb/d/de/360_Diffuser.png/300px-360_Diffuser.png)
Front panel - Light in the stand "Dispersion Window" immediatley below the loudspeaker.
LED |
OFF |
ON |
Flash / Blink |
RED |
Diffuser light (between cabinet and stand) | No power | Ready to Rock n Roll | Starting up or Fallback mode | Amplifier fault |
- Back panel
LED |
OFF |
ON |
Flash / Blink |
0 Master Port | No Link | Link Discovered | Link Activity |
1 Audio Clock | No Clock | Clock locked | Clock not locked |
2 Slave Port | No Link | Link Enabled | Link Activity |
3 Software Status | Not Configured | Running | Hardware Fault |
Safety
- Beryllium Dome Tweeter
- Important Safety Information
The outstanding high frequency reproduction from this loudspeaker is made possible through deployment of a beryllium dome tweeter.
The diaphragm contains 99% pure beryllium. Beryllium dust is a hazardous material, not to enter the human body, and waste material must be controlled.
Handling solid beryllium poses no significant health risks and if left undisturbed the beryllium tweeter is safe.
- It is important that you comply with the following safety precautions.
- • Do NOT remove the protective grille.
- • Do NOT open or disassemble the tweeter.
- • If the beryllium dome has been in a fire zone, follow the safety recommendations in the material safety data sheet - Click to view/download
If the tweeter dome is handled aggressively, it will likely dent, however should the tweeter dome break small particles of beryllium may be released and if airborne these would pose a health risk.
If your tweeter dome is broken, use double plastic bags, collect loose particles with adhesive tape and put it in the plastic bag. Immediately contact your retailer.
All tweeters requiring repair or service must be returned to the manufacturer to allow safe recycling of the beryllium material – your retailer will handle this for you.
At the end of the speaker’s life the beryllium material must be disposed of safely. Take the drive unit to an appropriate recycling or hazardous waste disposal site.
For handling beryllium, always follow the safety recommendations in the material safety data sheet - Click to view/download
FAQ
Linn 360 common FAQ's to both PWAB and Exakt variants
The 360 has two 8” bass drive units just like the Klimax 350. How does it produce more bass?
- The bass drivers in the 360 loudspeaker have the same surface area but are capable of greater than twice the excursion of the units deployed in the Klimax 350. This means they can move more than twice the amount of air.
- This is equivalent to the Klimax 350 with four bass drivers.
What is the Linn Power DAC?
- Linn Power DAC is a new amplifier technology specifically designed for bass systems that require high performance, high power, and high efficiency. The Linn Power DAC is a true digital amplifier combining DAC and amplifier into a single process.
- At high playback levels the Power DAC reduces distortion by over 10 dB compared to conventional designs.
Is the 360 bass system servo controlled?
- No. In 360 we have taken a feed-forward approach.
- The response of each bass drive unit is measured, and individual compensation filters are calculated. These filters are then applied in a feed-forward fashion to achieve the same result as the feed-back servo system.
- The 360 bass drive units are also far more linear than those previously used, so distortion correction is no longer required.
Linn 360 PWAB FAQ's
Why is 360 PWAB not a purely passive speaker?
- The compact size of the 360 bass system requires electronic compensation to achieve an extended bass response. This compensation cannot be implemented passively, so active amplification is required.
Why is the bass signal digitized in 360 PWAB?
- The analogue signal supplied to the 360 PWAB is digitized and fed into the new Linn Power DAC.
- The Power DAC has been designed from the ground up to drive the 360 bass system. It offers the lowest distortion and greatest efficiency of any amplifier class for this application.
Why can’t you bypass the internal lower bass amps on 360 PWAB to use Klimax Solos externally?
- The bass extension system in 360 requires an extraordinary amount of power and voltage gain, far more than even the Klimax Solo can provide, so performance would actually suffer if external amplifiers were used.
Do you still require 2x Exaktboxes for an externally Exakt 360 PWAB?
- No. The active bass system contains its own ExaktEngine, so a pair of 360 Arrays (tweeter, midrange and upper-bass) can be driven by a single 6-channel ExaktBox.
For full 360 FAQ's - click HERE