Difference between revisions of "Sekrit DSM"
m (→Product info) |
m |
||
| Line 4: | Line 4: | ||
* ''Product Name:'' Sekrit DSM (2012 / 2018 Variant) | * ''Product Name:'' Sekrit DSM (2012 / 2018 Variant) | ||
| − | * ''Date of Introduction:'' December 2012 | + | * ''Date of Introduction:'' December 2012 - July 2021'' |
| − | |||
* ''Type:'' Integrated digital music player, pre-amplifier, and power amplifier | * ''Type:'' Integrated digital music player, pre-amplifier, and power amplifier | ||
Revision as of 15:23, 24 January 2022
Contents
Product info
- Product Name: Sekrit DSM (2012 / 2018 Variant)
- Date of Introduction: December 2012 - July 2021
- Type: Integrated digital music player, pre-amplifier, and power amplifier
- Dimensions: 345 mm (width) x 44 mm (height) x 196.5mm (depth)
- Features
Support
Latest software
Details of latest Product release software
Manuals
Third Party Software Copyright
Audio Latency
Back Panel Connections
- MAINS INPUT - To connect to the mains electricity supply.
- FALLBACK - To put the device into Fallback mode (used when reprogramming)
- ETHERNET - To connect to a network (100Base-T)
- HDMI OUTPUT - To connect to a display device with HDMI 1.4 inputs.
- HDMI INPUTS - To connect sources with HDMI 1.4 outputs.
- ANALOGUE OUTPUT (RCA, variable/fixed level) - To connect to subwoofer (note:when the internal volume control is disabled, this will also disable the internal Power amplifier/speaker outputs) with unbalanced (RCA) analogue inputs.
- IR OUTPUTS - To connect to infrared flasher devices allowing control of other products that accept infra-red signals.
- DIGITAL INPUT (Toslink) - To connect sources with Toslink (optical) digital outputs.
- DIGITAL INPUT (Spdif) - To connect sources with Spdif (RCA) digital outputs.
- ANALOGUE INPUT (line level) - To connect a turntable or line level source with unbalanced (RCA) outputs.
- SPEAKER OUTPUTS - To connect to loudspeakers, Neutrik 4 pole connector
- RC5 ACCESSORY - To connect Linn BASIK3 or BASIK3-IR Room Control units, (setup for RoomAmp2 connection (jumper link removed)). Standard IR receivers cannot be used in this socket. This requires a Knekt-CAT-5 cable to connect to the Linn DSM
Front Panel Connections
- IR SENSOR - Recieves IR commands
- DIAGNOSTIC LEDS - See table below for functionality
- FALLBACK - To put the device into Fallback mode (used when reprogramming) (F-BACK)
- POWER SWITCH- Switches the power on/off
- IR REPEATER CLAMP- IR Repeater Clamp fixing screws
DIAGNOSTIC LED FUNCTIONS
|
Text |
ON indicates |
OFF indicates |
Slow Flash / Blink |
Fast Flash |
| IR | Pulse on IR command received | Reserved for future use | Reserved for future use | n/a |
| AMP | Internal amplifier enabled | Internal amplifier disabled | Internal amplifier fault | n/a |
| AUDIO | Valid audio (digital inputs only) | n/a | Invalid audio (digital inputs only) | n/a |
| IP | DHCP IP address obtained | Default IP address obtained | n/a | n/a |
| NET | Ethernet link established | no link established | n/a | n/a |
| STBY | Device in standby | Device active | Searching for IP address (boot) | Fallback (reprogramme) |
Speaker Wiring
The Sekrit DSM has 4 DAC channels and 4 Power Amplifiers. These amplifiers can be configured in single ended mode or bridged mode. All speaker outputs (and Analogue Output) share the same common Volume control.
Connections to the speakers are made via Neutrik Speakon connectors, NL4FX. Neutrik Speakon Assembly Instructions
The single ended mode is best suited to bi-amping a pair of passive speakers or for driving multiple pairs of loadspeakers. Bridged mode is best suited to driving a single pair of loudspeakers.
The wiring details are shown below:
- 33W/channel in single-ended mode
- 50W/channel in bridged mode
Installation
Please read the following carefully before installing the unit in your system – your unit may need to be reconfigured by your Linn retailer.
FAQ's
Check:
For further assistance, try our customer support pages
