Difference between revisions of "Sneaky DSM"

MAINS INPUT - To connect to the mains electricity supply.
FALLBACK - To put the device into Fallback mode (used when reprogramming)
ETHERNET - To connect to a network (100Base-T)
HDMI OUTPUT - To connect to a display device with HDMI inputs.
HDMI INPUTS (3) - To connect sources with HDMI outputs.
ANALOGUE OUTPUT (RCA, variable/fixed level) - To connect to subwoofer or external power amplifier (or pre amplifier when internal volume control is disabled, this will also disable the internal Power amplifier/speaker outputs) with unbalanced (RCA) analogue inputs.
DIGITAL INPUT (Toslink) - To connect sources with Toslink (optical) digital outputs.
DIGITAL INPUT (Spdif) - To connect sources with Spdif (RCA) digital outputs.
ANALOGUE INPUT (line level) - To connect a turntable or line level source with unbalanced (RCA) outputs.
SPEAKER OUTPUTS - To connect to loudspeakers, Neutrik 4 pole connector

Front Panel Connections

Front Slot - contains the IR sensor and the Standby LED

STANDBY LED FUNCTIONS

DIM/OFF

indicates

BRIGHT/ON

indicates

Slow Flash

Fast Flash

Device in standby

Device active (will also pulse on IR command received)

Searching for IP address (boot)

Fallback (reprogramme)

Speaker Wiring

The Sneaky DSM has 4 DAC channels and 4 Power Amplifiers. These amplifiers can be configured in stereo mode or bi-amped mode (via Konfig). All speaker outputs (and Analogue Output) share the same common Volume control.

Connections to the speakers are made via Neutrik Speakon connectors, NL4FX. Neutrik Speakon Assembly Instructions or check Neutrik website for NL4FX information

The stereo mode is best suited to connecting to passive one-way speakers. Power output is 33W/channel (2 x 33) into 4ohm

1+ -> Speaker +
1- -> Speaker -
2+ -> Not Connected
2- -> Not Connected

The bi-amped mode is best suited to connecting to passive two-way speakers. Power output is 33W/channel (4 x 33) into 4ohm

1+ -> Speaker 1+
1- -> Speaker 1-
2+ -> Speaker 2+
2- -> Speaker 2-

Installation

Please read the following carefully before installing the unit in your system – your unit may need to be reconfigured by your Linn retailer.

Unpacking Information

Positioning Information

Amplifier Protection

Sneaky DSM FAQ's

HARDWARE

HDMI

The Sekrit DSM/Sneaky DSM are only available with HDMI 1.4 connections.

This product does NOT support ARC (Audio Return Channel)

Difference between Sneaky DSM & Sekrit DSM

Sekrit DSM has

A chassis (case) that can be mounted in a 19” (RAKK-SNKMDS) with power switch & Fallback on the front of the case
Indicator leds to give the operational/connection status of the Sekrit DSM
Can be used with BASIK-3 or BASIK-3-IR RCU
The option to screw an IR emitter over DSM IR receiver. This is intended for IR repeater control interface whilst the Sekrit DSM is hidden.
Full range Power Amplifier with the (Configured in Konfig)

a. Single ended option of 4x33W. For driving two pairs of in-wall/in-ceiling speakers with common volume control.

b. Bridged mode of 2x50W. For driving one pair of speakers. (This requires wiring the Nuetrik plug for bridged mode)

Sneaky DSM has

A chassis (case) for table top positioning with side power switch. Fallback button on rear connector panel
Front panel power indicator that flashes when IR command is being received or in boot mode awaiting a DHCP address.
Full range Power Amplifier with the (Configured in Konfig)

a. Single ended option of 2x33W. For driving one pair of speakers in single amp mode.

b. Single ended option of 4x33W. For driving one pair of speakers in Bi-AMP mode.

For further assistance, try our customer support pages

@@ Line 1: / Line 1: @@
-[[Image:SneakyDsmFront.jpg|right|350px]]
+[[Image:SneakyDsmMain.png|right|550px]]
 == '''Product info''' ==
-* ''Product Name:'' Sneaky DSM
+* ''Product Name:'' Sneaky DSM (2013 Variant)
-* ''Date of Introduction:'' February 2012
+* ''Date of Introduction:'' February 2013 - September 2017
 * ''Type:'' Integrated digital music player, pre-amplifier, and power amplifier
@@ Line 20: / Line 20: @@
 == '''Latest software''' ==
-[http://www.linn.co.uk/ds_software Latest software releases]
+{{General:Latest_Product_SW}}
-[http://oss.linn.co.uk/trac Open source software]
 == '''Manuals''' ==
-[http://docs.linn.co.uk/wiki/index.php/Konfig_Manual Konfig manual]
+{{General:Product_Manuals}}
-[http://oss.linn.co.uk/trac/wiki/KinskyDesktopManual Kinsky Desktop manual]
-[http://docs.linn.co.uk/wiki/index.php/REM_020 DSM Remote control manual]
-[http://docs.linn.co.uk/wiki/images/1/1b/Linn_Safety_Info.pdf Safety Information]
+== '''Audio Latency''' ==
-[http://www.linn.co.uk/warranty Warranty Terms and Conditions]
+[[DSM Audio Latencies Explained]]
-== '''HDMI Setup''' ==
-[[HDMI Setup]]
 == '''Network Setup''' ==
-[[DS Budget System| DS Budget System Setup]]
+{{General:DS_Network_system}}
-[[DS Entry Level System| DS Entry Level System Setup]]
-[[DS High End System| DS High End System Setup]]
 == '''Back Panel Connections''' ==
-[[Image:SneakyDsmRear.jpg|center|700px]]
+[[Image:SneakyDsmRear.png|center|700px|link=]]
-# '''MAINS INPUT''' - To connect to the mains electricity supply.
+# {{link:MAINS INPUT}}
-# '''FALLBACK'''- To put the device into Fallback mode (used when reprogramming).
+# {{link:FALLBACK}}
-# '''ETHERNET''' - To connect to a network.
+# {{link:ETHERNET}}
 # '''HDMI OUTPUT''' - To connect to a display device with HDMI inputs.
-# '''HDMI INPUTS''' - To connect sources with HDMI outputs.
+# '''HDMI INPUTS (3)''' - To connect sources with HDMI outputs.
 # '''ANALOGUE OUTPUT''' (RCA, variable/fixed level) - To connect to subwoofer or external power amplifier (or pre amplifier when internal volume control is disabled, this will also disable the internal Power amplifier/speaker outputs) with unbalanced (RCA) analogue inputs.
-# '''IR OUTPUTS''' - To connect to infrared flasher devices allowing control of other products that accept infra-red signals.
 # '''DIGITAL INPUT''' (Toslink) - To connect sources with Toslink (optical) digital outputs.
 # '''DIGITAL INPUT''' (Spdif) - To connect sources with Spdif (RCA) digital outputs.
 # '''ANALOGUE INPUT''' (line level) - To connect a turntable or line level source with unbalanced (RCA) outputs.
 # '''SPEAKER OUTPUTS''' - To connect to loudspeakers, Neutrik 4 pole connector
-# '''RC5 ACCESSORY''' - To connect BASIK-3 & BASIK-3IR Room Control units. (Standard IR receivers cannot be used in this socket)
 <br>
 == '''Front Panel Connections''' ==
-[[Image:SekritDsmFront.jpg|center|700px]]
+[[Image:SneakyDsmFront.png|center|700px]]
-# '''IR SENSOR''' - Recieves IR commands
+# '''Front Slot''' - contains the IR sensor and the Standby LED
-# '''DIAGNOSTIC LEDS''' - See table below for functionality
-# '''FALLBACK (F-BACK)''' - To put the device into Fallback mode (used when reprogramming).
-# '''POWER SWITCH'''- Switches the power on/off
-# '''IR REPEATER CLAMP'''- IR Repeater Clamp fixing screws
 <br>
-'''DIAGNOSTIC LED FUNCTIONS'''
+'''STANDBY LED FUNCTIONS'''
 {| border="1" cellspacing="0" cellpadding="0" width="100%" align="center"
 |-
-| bgcolor="#cccccc" align="center" |
-'''''Text'''''
 | bgcolor="#cccccc" width="21%" align="center" |
-'''''ON'''''
+'''''DIM/OFF'''''
 '''''indicates'''''
 | bgcolor="#cccccc" width="21%" align="center" |
-'''''OFF'''''
+'''''BRIGHT/ON'''''
 '''''indicates'''''
 | bgcolor="#cccccc" width="21%" align="center" |
-'''''Slow''''' '''''Flash / Blink'''''
+'''''Slow''''' '''''Flash'''''
 | bgcolor="#cccccc" width="15%" align="center" |
 '''''Fast''''' '''''Flash''''' <br>
 |-
-| align="center" | '''IR'''
-| align="center" | Pulse on IR command received
-| align="center" | Reserved for future use
-| align="center" | Reserved for future use
-| align="center" | n/a
-|-
-| align="center" | '''AMP'''
-| align="center" | Internal amplifier enabled
-| align="center" | Internal amplifier disabled
-| align="center" | Internal amplifier fault
-| align="center" | n/a
-|-
-| align="center" | '''AUDIO'''
-| align="center" | Valid audio (digital inputs only)
-| align="center" | n/a
-| align="center" | Invalid audio (digital inputs only)
-| align="center" | n/a
-|-
-| align="center" | '''IP'''
-| align="center" | DHCP IP address obtained
-| align="center" | Default IP address obtained
-| align="center" | n/a
-| align="center" | n/a
 |-
-| align="center" | '''NET'''
-| align="center" | Ethernet link established
-| align="center" | no link established
-| align="center" | n/a
-| align="center" | n/a
-|-
-| align="center" | '''STBY'''
 | align="center" | Device in standby
-| align="center" | Device active
+| align="center" | Device active (will also pulse on IR command received)
 | align="center" | Searching for IP address (boot)
 | align="center" | Fallback (reprogramme)
@@ Line 139: / Line 87: @@
 == '''Speaker Wiring''' ==
-The Sekrit DSM has 4 DAC channels and 4 Power Amplifiers.  These amplifiers can be configured in single ended mode or bridged mode.  All speaker outputs (and Analogue Output) share the same common Volume control.
+The Sneaky DSM has 4 DAC channels and 4 Power Amplifiers.  These amplifiers can be configured in stereo mode or bi-amped mode (via Konfig).  All speaker outputs (and Analogue Output) share the same common Volume control.
 Connections to the speakers are made via Neutrik Speakon connectors, NL4FX.
-[http://www.neutrik.com/zoolu-website/media/download/146/Assembly+Instruction+-+speakON+System  Neutrik Speakon Assembly Instructions]
+[https://www.neutrik.com/media/11062/download/bda-114---speakon-nl4fx--nl4frx.pdf?v=1  Neutrik Speakon Assembly Instructions] or check [https://www.neutrik.com Neutrik website for NL4FX information]
-The single ended mode is best suited to bi-amping a pair of passive speakers or for driving multiple pairs of loadspeakers.  Bridged mode is best suited to driving a single pair of loudspeakers.
+The '''stereo mode''' is best suited to connecting to passive one-way speakers. Power output is 33W/channel (2 x 33) into 4ohm
+[[Image:NeutrikConnector.png|left|100px]]
-The wiring details are shown below:
++ -> Speaker +
-<br><br>
+- -> Speaker -
-[[Image:SekritDsmWiring.jpg|center|700px]]
++ -> Not Connected
+- -> Not Connected
 <br>
-* 33W/channel in single-ended mode
+The '''bi-amped mode''' is best suited to connecting to passive two-way speakers. Power output is 33W/channel (4 x 33) into 4ohm
-* 50W/channel in bridged mode
+[[Image:NeutrikConnector.png|left|100px]]
++ -> Speaker 1+
+- -> Speaker 1-
++ -> Speaker 2+
+- -> Speaker 2-
 <br>
@@ Line 158: / Line 111: @@
 Please read the following carefully '''before''' installing the unit in your system – your unit may need to be reconfigured by your Linn retailer.
-* [http://docs.linn.co.uk/wiki/index.php/product_unpacking Unpacking Information]
+* [[product_unpacking |Unpacking Information]]
+* [[product_positioning |Positioning Information]]
+* [[amplifier_protection  |Amplifier Protection]]
-* [http://docs.linn.co.uk/wiki/index.php/product_positioning Positioning Information]
+== Sneaky DSM FAQ's ==
+{{FAQ:SekritDSM FAQ}}
-* [http://docs.linn.co.uk/wiki/index.php/amplifier_protection  Amplifier Protection]
+For further assistance, try our [http://www.linn.co.uk/linn_customer_support customer support] pages
-For further assistance, try our [http://www.linn.co.uk/linn_customer_support customer support] pages or the [http://Forums.linn.co.uk Linn Forum.]
+[[Category:Linn_DSM]]
+[[Category:CORE1]]

Difference between revisions of "Sneaky DSM"

Latest revision as of 13:14, 4 December 2023

Contents

Product info

Support

Latest software

Manuals

Audio Latency

Network Setup

Back Panel Connections

Front Panel Connections

Speaker Wiring

Installation

Sneaky DSM FAQ's

HARDWARE

HDMI

Difference between Sneaky DSM & Sekrit DSM

Navigation menu

Personal tools

Namespaces

Variants

Views

More

Search

Navigation

Product selection

Software/Setup

FAQ's

Support

Indexes

Useful Websites

Search

Tools