Klimax 350 Exakt

From LinnDocs
Revision as of 10:43, 11 January 2016 by Yoda (talk | contribs) (Product info)
Jump to: navigation, search
Klimax.350.BLK-GLOSS.jpg


Product info

  • Product Name: Klimax Exakt 350 Loudspeakers
  • Date of Introduction: September 2013
  • Type: 6-way Fully Integrated Aktiv Loudspeaker with Exakt Technology


Manuals

Safety Information

Warranty Terms & Conditions

Linn Support Site


Installation

We recommend that your Linn Klimax loudspeakers are unpacked, installed and adjusted by an authorised Linn retailer. To get the best from your Klimax loudspeakers, it is important that they are positioned and levelled correctly.

Please note, in order to achieve the very best from your Klimax 350's, some adjustment may be required after positioning, levelling and connecting. See the Fine adjustment section.



Unpacking

IMPORTANT: The Klimax speakers are heavy; take great care when moving them.
When unpacking, lifting or moving them, we recommend using two people to avoid personal injury.


  • Do not lift your speaker using the amplifier module, this will cause damage to your loudspeaker.
  • Do not lay the loudspeakers on their front face or the amplifier on the rear as this will damage the loudspeaker.
  • We recommend that you retain the packaging in case you need to transport your loudspeaker(s) at a later date.
  • Loudspeakers are packed individually with a separate package containing both speaker stands.
  • Take care when unpacking to avoid damage to the cabinets.


Move the (boxed) loudspeaker to an uncluttered, flat area adjacent to its eventual position (this will avoid any excessive moving and carrying of unpacked loudspeakers).

Stand the loudspeaker box on its base.

Cut the bands holding the end caps in place

Remove the cardboard sleeve by lifting it straight up until it clears the top of the cabinet

Leaving the top end cap on (to protect the loudspeaker) turn the Akubarik upside down.

Remove the bottom end caps to allow the stand to be fitted, see below


Once the stand has been fitted, carefully rotate speaker onto the stand. Lift the loudspeaker out of the top end-cap and remove its protective bag.

Leave the packaging between the amplifier module and the cabinet and the 3-K Array cover in place until the loudspeakers have been moved to their final position.

Once you have positioned the loudspeakers, remove the two packaging pieces between the amplifier and the cabinet and VERY CAREFULLY snip the plastic tie holding the 3-K Array cover in place and remove it.


Fitting the Stand

On a clean, level surface that will not damage the loudspeaker; carefully stand the speaker upside-down using an end-cap for stability without laying it on its front or rear face.

Remove the ten bolts holding the transit plinth in place using a 2.5mm/4mm Hex key.

Remove the transit plinths and retain with the packaging in case you need to transport your loudspeaker(s) in the future.

Position the speaker stand above the speaker as shown above and attach using the 6 bolts supplied with stand.


IMPORTANT: Take care not to over tighten the bolts.

Positioning

As with any stereo loudspeaker there are some fundamental principles which should be observed to get the best sound from your loudspeakers.

  • The loudspeakers should be place at an equal distance from the wall behind the loudspeakers.
  • The speakers should be a similar (not the same) distance from the walls to the outside of each loudspeaker.
  • Any toe-in applied should be the same for each loudspeaker.
  • The loudspeakers should be level with all four spikes in contact with the floor. Use Linn Skeets for hard floors.

As the Klimax loudspeaker low frequency performance will be better if the loudspeakers are pulled out from the wall, 10-20cm from the rear wall and 30-40cm from the side walls are a good starting point, but adjustment will be required to get the best results. Additional benefit will be heard in the upper midrange and high frequencies by placing the loudspeakers away from the rear wall.

The Linn 3K Array used in the Klimax 350 loudspeaker offers exceptional dispersion characteristics. This means that there should be little or no need to toe-in your loudspeakers.


For further assistance, try our customer support pages or the Linn Forum.


Levelling

Image:Adjust Spikes.jpg




Screw the spikes into the corners of the stand.
Fit the lock nuts but do not tighten at this stage.




Image:Level_350_spkrs.jpg‎‎


Very carefully (do not scratch the cabinet), use a spirit level to check if it is sitting level. If it is, gently rock the loudspeaker from front to back, side to side and diagonally to check for any movement. If none is present and the loudspeaker is sitting level, no adjustment to the spikes is necessary.


If the loudspeaker is not level, or moves when you rock it, loosen the appropriate lock nuts using the tool provided and use a screwdriver to turn the spikes to adjust their height. Adjust the spikes to level the speaker, using a spirit level placed on the stand.

Press down firmly on the top of the loudspeaker to ensure it is in close contact with your flooring.

Image:Tighten spikes.jpg

Use the spirit level as before and continue to adjust the spikes as required.




Once the speaker is level and does not rock, use the screwdriver to hold the spike in place and fit and tighten the lock nuts with the spanner provided.


Note: To protect wooden or tiled floors, the spikes can be placed on Linn Skeets which are available from your Linn retailer.

Connections & operation

Back Panel

Image:Klimax Exakt 350


  1. MAINS INPUT - To connect to the mains electricity supply.
  2. POWER SWITCH - To connect sources with phono outputs.
  3. FALLBACK - Primarily for Linn service use only, to put the device into Fallback mode (used when reprogramming the unit).
    Note: The LED behind the Fallback indicates the Exakt Link is active but the product is not powered/switched off.
  4. EXAKT LINK - From Exakt Master OR from a Exakt Slave connected to the Exakt master
  5. EXAKT LINK - To Exakt Slave product
  6. STATUS INDICATORS - Function of the LED's are given below:


EXAKT LINK connection

Check HERE for information of Exakt link connection

LED Status

Front panel

LED

OFF

ON

Flash / Blink

Exakt Logo No power Ready to Rock n Roll Starting up or Fallback mode






Back panel

LED

OFF

ON

Flash / Blink

0 Master Port No Link Link Discovered Link Activity
1 Audio Clock No Clock Clock locked Clock not locked
2 Slave Port No Link Link Enabled Link Activity
3 Software Status Not Configured Running Hardware Fault













Trouble shooting

Check Exakt trouble shooting