The Linn DSM products provide HDMI pass through of HDMI V1.4 and HDMI 2.0 (for Products with the HDMI2 board) signals
The Linn DSM products HDMI output will:-
1. Pass-through the HDMI audio when the Linn DSM is in Standby.
2. Pass-through the HDMI audio when the Linn DSM is listening to an Analogue or Digital Audio input.
3. BLOCK the HDMI audio to the TV if the the DSM is listening to an HDMI input.
- 1 ARC - Audio Return Channel
- 2 I cannot get any picture through the HDMI
- 3 No Audio playback on HDMI connection
- 4 Audio keeps muting/unmuting
- 5 APPLE TV4 switching TV On and Off Plus controlling Tv volume
- 6 No Audio from a Linn DSM HDMI connection
- 7 Hiss or White noise Audio from a Linn DSM HDMI connection
- 8 Do Linn DSM products support HDMI 2.1?
ARC - Audio Return Channel
Only the Klimax DSM / Akurate DSM / Majik DSM with HDMI2 boards (>Sept 2016) plus the Selekt DSM & Series 3 (301) will support this connection.
I cannot get any picture through the HDMI
The Linn DSM with HDMI2 board supports 4k resolution
The Playstation3 is known to have HDMI connection issues with many non-Linn devices.
- Select PS3 input on the Linn DSM
- While the PLAYSTATION 3 system is in standby mode (red light on the front of the system), hold down the touch-sensitive power button on the front of the system until the system goes into standby mode again . (So the light cycle would go from: red light --> green light --> then back to red light). This will ensure that you have held down the power button long enough to reset the Video Output Settings.
Virgin Media V6 / Sky-Q
The Virgin Media V6 & Sky-Q boxes are very strict on HDCP issues, as these work in HDCP 2.2. It has been found that if your TV or Projector only supports HDCP 1.3 and your AV Receiver (Linn DSM or other manufacturer) supports HDCP 2.2 then the mismatch will cause the Virgin Media V6/Sky-Q box NOT to send video (due to encryption issues).
The solution is to put an HDCP convertor, such as the LINDY or NEET Bidirectional HDCP Converter, V2.2 to V1.4, between the Virgin Media V6 or Sky-Q HDMI output and Linn DSM HDMI input. This will force all communications to HDCP 1.3
Some customers have found disabling "CEC" and "CEC Auto Select Source" on HDMI section of Konfig will fix this issue. (Do the Konfig changes and power cycle the Virgin Media/Sky box)
Apple MacMini, MacBook Pro etc
If you switch the DSM to the HDMI feed from a MacMini, MacBook, etc. it will initially lose any picture and audio. This may take up to 30 seconds to appear and for the audio to return. This delay is due to the Mac performing HDMI communication and re-establishing the audio and video options.
HDMI connection with Video scalers
If you have a video scaler in the HDMI chain and you are not getting any picture through the Linn DSM, take the video scaler out of the system to see if the picture returns.
No Audio playback on HDMI connection
The standard Linn DSM will ONLY support 2ch (or multichannel) PCM audio. It does not support Dolby Digital, DTS, etc. unless you have a Linn Surround Module installed in your Linn DSM.
If you feed an unsupported audio format from your DVD player, sat receiver, etc. the Linn DSM can pass this through to the TV if the DS is in standby mode. If when you select that input on the DSM there is no audio then double check that the audio out on the DVD/Sat is configured for 2ch PCM.
Audio keeps muting/unmuting
If your Linn DSM has an HDMI2 board then this may be the TV trying to control the Linn DSM volume.
Go into Konfig > your Linn DSM > HDMI. DISABLE the CEC settings and reboot the Linn DSM. This should stop this mute/unmute from occuring.
APPLE TV4 switching TV On and Off Plus controlling Tv volume
When using an Apple TV4 with a Linn DSM with HDMI2 (>Sept 2016).
- We would advise to go into the Apple TV settings > "Remotes and Devices" and
- turn OFF "Control TV's and Receivers".
- turn OFF "Control TV's and Receivers".
Otherwise the TV may be confused about its power state and Audio Return Channel (ARC - Audio from TV to Linn DSM).
You can use the Apple TV handset to control the Linn DSM volume by IR if this is required.
No Audio from a Linn DSM HDMI connection
The standard Linn DSM will ONLY support 2ch (or multichannel) PCM audio. It does not support Dolby Digital, DTS etc unless you have a Linn Surround Module installed in your Linn DSM.
- On Davaar 55, the surround function has been added.
- If the incoming audio from the HDMI source is multi-channel PCM, this audio is NOT broadcast using Songcast.
- This will occur even if you only have a pair of speakers defined on the Linn DSM, it still has to downmix the incoming multi-channel audio.
If you only have the front Left & Right speakers defined in Konfig the solution is to go to your HDMI source and change its HDMI audio output to Stereo PCM.
Hiss or White noise Audio from a Linn DSM HDMI connection
This means that the Linn DSM is playing an unsupported codec. This can happen if you are trying to play, for example, a DTS-CD track. (This is normally caught in HDMI communication but some audio formats send encoded data in a normal format)
Check to see if your Media player/Blu-Ray/DVD player can decode this into Multi-Channel PCM.
Do Linn DSM products support HDMI 2.1?
Linn DSM products do not currently support the HDMI 2.1 specification.
HDMI 2.0 deals with 4K video with 18GHz bandwidth and is compatible with current Majik, Akurate and Klimax DSM products.
HDMI 2.1 deals with up to 10K video with 48GHz bandwidth and at the time of writing (March 2019) there are no cables, sources or playback devices commercially available supporting this specification.