Difference between revisions of "Majik-I"

From LinnDocs
Jump to: navigation, search
(Setup Menus)
Line 86: Line 86:
  
 
The Main Menu Menu consists of four sub Menus:
 
The Main Menu Menu consists of four sub Menus:
* [http://docs.linn.co.uk/wiki/index.php/MDI_Display_Config Display Configuration]
+
* [http://docs.linn.co.uk/wiki/index.php/Majik-I_Display_Configuration Display Configuration]
* [http://docs.linn.co.uk/wiki/index.php/MDI_Source_Config Source Configuration]
+
* [http://docs.linn.co.uk/wiki/index.php/Majik-I_Source_Configuration Source Configuration]
* [http://docs.linn.co.uk/wiki/index.php/MDI_Audio_Config Audio Configuration]
+
* [http://docs.linn.co.uk/wiki/index.php/Majik-I_Audio_Configuration Audio Configuration]
* [http://docs.linn.co.uk/wiki/index.php/MDI_Unit_Config Unit Configuration]
+
* [http://docs.linn.co.uk/wiki/index.php/Majik-I_Unit_Configuration Unit Configuration]
 
* '''Display Configuration'''
 
* '''Display Configuration'''
 
* '''Source Configuration'''
 
* '''Source Configuration'''

Revision as of 15:52, 21 May 2012

DRAFT

Product info

  • Product Name: Majik-I
  • Date of Introduction: October 2007
  • Type: Integrated preamplifier and power amplifier


Manuals

Remote Control manual

Safety Information

Warranty Terms & Conditions


Back Panel Connections

Image:Majik_DS-I_rear.jpg


  1. MAINS INPUT - To connect to the mains electricity supply.
  1. EARTH GROUND - To connect to a turntable grounding terminal, or an earthing terminal if no mains earth is available, or to join to the earths of other products in the system to improve performance in areas of poor/noisy electrical earth conditions.
  2. SPEAKER OUTPUTS - To connect to loudspeakers
  3. ANALOGUE OUTPUTS (RCA, variable level) - To connect to a preamplifier with unbalanced (RCA) inputs.
  4. ANALOGUE OUTPUTS (RCA, fixed level) - To connect to an analogue recording device with unbalanced (RCA) inputs.
  5. ANALOGUE INPUTS (RCA, line level) - To connect sources with unbalanced (RCA) analogue outputs. Input 6 is a configurable input, which is factory set as a moving magnet phono input for connection to turntables. It can be changed by a Linn dealer to a line-level input or a moving coil phono input (moving coil is an optional upgrade).
  6. RS232 PORTS - For connection to Linn source products without ethernet ports.


Front Panel Connections

Majik-I front.jpg
  1. MUTE BUTTON - Mutes/unmutes the audio
  2. FRONT PANEL DISPLAY
  3. STANDBY BUTTON - Brings the unit in/out of standby
  4. VOLUME ADJUST BUTTONS - Changes the volume up/down
  5. HEADPHONE OUTPUT (3.5mm stereo) - To connect to headphones
  6. AUXILIARY SOURCE INPUT (3.5mm stereo) - To connect to an analogue stereo audio source
  7. SOURCE ADJUST BUTTONS - Changes to the previous/next source


Installation

Please read the following carefully before installing the unit in your system – your unit may need to be reconfigured by your Linn retailer.


For further assistance, try our customer support pages or the Linn Forum.

Setup Menus

The setup menus can be used to configure the Majik-I to customise aspects of its operation to suit your requirements, to operate in a particular type of installation, or to view important functional data.

Entering and Navigating setup Using the Front Panel

  • Press and Hold the MUTE button until "main Menu" appears on the front panel display.
  • Navigate up or down the options within a menu using SOURCE+ or SOURCE-
  • Press VOLUME+ or STANDBY to select an option.
  • Press VOLUME- to go back to the previous option or menu.
  • Press MUTE to exit Setup.

NOTE: For each option the currently selected setting will be indicated by a tick beside it.

The Main Menu Menu consists of four sub Menus:

The contents of these Menus are shown below

DISPLAY CONFIGURATION
OPTION Settings Description Default Setting
Display Brightness

Auto or Percentage

(2% to 100%)

If set to ‘Auto’, the display brightness will change with the surrounding lighting conditions (dimmer surroundings => dimmer display / brighter surroundings => brighter display).

To select ‘Auto’, scroll up or down the percentage settings and the ‘Auto’ option will appear in place of 0%.

With ‘Percentage’, you can select a setting between 2% and 100%. The display brightness will (while out of standby) remain set to the specified brightness setting.

100%

Display Content Source and Volume

Volume Source Last Used

If set to ‘Source and Volume’, both the currently selected source and the current volume setting will be displayed on the front panel.

If set to ‘Volume’, only the current volume setting will be displayed.

If set to ‘Source’, only the current source setting will be displayed.

If set to ‘Last Used’, the last setting (source or volume) to be adjusted will remain on the display.

Note:The above settings are applicable only when the unit is out of standby, is not in display-sleep mode and is not being adjusted.

Source and Volume
Display Timeout 1 - 10 seconds Determines how long, after an adjustment is made, before the display reverts to its ‘Display Content’ setting as detailed above. 2 seconds
Sleep Display Delay Delay in Minutes and Seconds

(0 seconds - 5 minutes)

The time setting determines how long after the last command has been received that the display goes to sleep (where only 3 dots are visible on the display).

If set to ‘Off’, the display will not go to sleep

off
SOURCE CONFIGURATION
OPTION Settings Description Default Setting
Name N/A Allows you to customise the input name as it appears on the display. Any name can be entered, up to a maximum of 12 characters (including spaces).

To change the selected input name:

  • Use the ▼/▲ keys on the handset or SOURCE – / + keys on the front panel to change the flashing character.
  • Use the ▶ key on the handset or VOLUME + key on the front panel to move to the next character.
  • Use the ◀ key on the handset or VOLUME – key on the front panel if you wish to move to the previous character.
  • Once you are happy with your changes press ● on the handset or �STANDBY on the front panel.

To exit and go back to the menu, repeatedly press the ◀ key on the handset or VOLUME – on the front panel.

Socket=Name

Aux=Aux

Input 1=MajikCD

Input 2=Input 2

Input 3=Input 3

Input 4=Input 4

Input 5=Input 5

Input 6=Phono


Type
Volume Offset -15 to +15 Allows the volume level of each source input to be adjusted up or down, relative to the others. Allows you to equalise the volume across all sources. For example if a CD player and a radio tuner are connected, the CD player’s output volume may be louder than that of the tuner so this feature saves volume adjustment when switching between these sources.

Note:The volume difference will not be visible on the volume display – so when switching between offset sources, the volume display will not reflect the offset.

0
AUDIO CONFIGURATION
OPTION Settings Description Default Setting
Volume Rate 1/10 -

10/10

Allows you to adjust the rate at which the volume changes when the VOLUME – / + keys are held down. 8/10
Mute Rate 1/10 -

10/10

Allows you to adjust the rate at which the volume mutes/unmutes when the MUTE key is pressed. 8/10
Volume Limit 0 - 100 Allows you to limit the unit’s maximum volume.

For example, if you set the volume limit to 60, the volume cannot be raised above 60.

100
Volume Preset 0 - 100 Allows you to adjust the volume level that the unit will be set to when it comes out of standby. 40
Headphone Offset -15 to +15 Allows the volume of the headphone output to be adjusted up or down, relative to the loudspeaker volume.

This option enables you to compensate for the different outputs of different headphone types. So after adjusting the offset, when headphones are connected or disconnected, the volume should not require adjusting.

0
UNIT CONFIGURATION
OPTION Settings Description Default Setting
Selection Timeout 1 - 10 seconds Allows you to adjust the time taken for source selection to take effect. A delay allows you time to scroll through and view available sources. 1 second
Startup Source None

Last Used

Aux

Phono

Input 5

Input 4

Input 3

Input 2

Majik CD

Allows you to set which source input will be selected when the unit comes out of standby.

Note: The names shown are configured in the Source Configuration options.

Last Used
Standby Record From None

Last Used

Aux

Phono

Input 5

Input 4

Input 3

Input 2

Majik CD

Allows you to set a source to be output at TAPE OUT while the unit is in standby.

Note: The names shown are configured in the Source Configuration options.

Last Used
Handset Commands Enabled

Disabled

If set to Enable, the unit will accept remote commands from the handset.

If set to Disabled, the unit will not accept remote commands from the handset. (Setup menus will only be accessible and adjustable via the front panel controls.)

Enabled
RS232 Configuration N/A This option accesses the RS232 setup sub-menu – used to configure the unit to communicate with other RS232 enabled products.
Defaults N/A This option accesses the defaults sub-menu – used for saving and recalling configurations. N/A
Unit Information N/A Not adjustable – for information only. Allows the unit’s software/hardware revisions to be viewed. This category is mainly intended for Linn personnel and Linn-appointed service agents. N/A