Difference between revisions of "Fault finding"

From LinnDocs
Jump to: navigation, search
(Network conneciton fault solutions)
Line 82: Line 82:
  
 
==Network DHCP server/Router solutions==
 
==Network DHCP server/Router solutions==
 +
:;* No connection to DHCP server/Router: Suspect that your Linn DS/DSI is connected to another ethernet device (Switch, Homeplug), to the DHCP server/Router. Check the ethernet cables are connected to the correct network sockets on these devices and the DHCP server/Router is powered on
 +
 +
;;* There may not be any spare network addresses to connect any other devices to the network: Power Off the DHCP Server and rest of system as per [http://docs.linn.co.uk/wiki/index.php/Fault_finding#First_time_your_Linn_DS.2FDSI_system_has_stopped_working System has stopped working] for a minimum of 5minutes. The power switch everything on in the sequence stated in [http://docs.linn.co.uk/wiki/index.php/Fault_finding#First_time_your_Linn_DS.2FDSI_system_has_stopped_working System has stopped working]

Revision as of 14:57, 29 July 2011

First time your Linn DS/DSI system has stopped working

In this is the first time your system has stopped working or very rarely stops working, the system products may have got confused. The simple solution is to switch everything off, the switch everything back in a sequence.

  1. Remove power from ALL devices connected to the ethernet. (that is switch everything off, NOT STANDBY)
  2. Power on the Router/DHCP server
  3. Power on any network switches
  4. Power on the NAS (if used) and other ethernet devices
  5. Power on the Linn DS/DSI
  6. Power on your control devices, (PC, iPad, Pronto etc)

This will get the Linn DS/DSI system working again in most cases.

Top




You cannot see your Linn DS/DSI on your control device (PC, iPad etc)

Simple tests

If you cannot see your Linn DS/DSI using your control device, you will need to find out if this;

  • A control device issue
  • An Ethernet issue, or
  • A Linn DS issue

The easiest way to check this, (assuming you have a remote control and internet broadband connected to the Linn DS/DSI).

Top

Check the Linn DS/DSI operation

This is to test that the Linn DS/DSI can operate freely, (any control issues may be with the PC/iPad/ etc)

  1. On the remote control, press the PLAY button. If the Linn DS/DSI starts playing music this Linn DS/DSI is OK and you can ignore the remaining tests in this section.
  2. Use the remote control to select the Linn DS/DSI Radio source
  3. Continue with the Remote control and select a Radio station
  • You may have to try a couple of different Radio stations, but wait approx 10seconds before you change station if you get no audio/music.
  1. Adjust the volume of the Linn DS/DSI to a comfortable listening level.

Note: This may take a few seconds to sync with the internet Radio stream.

When the linn DS/DSI is playing Music, then use of remote control and the fact that the Radio is playing confirmes that the Linn DS/DSI is working and the Ethernet is good.
If there is NO audio/music, this may be an issue with the Linn DS/DSI and/or network it is connected to.

Top


Check Ethernet validity

If the Linn DS/DSi is not connected to the system or being granted access to your ethernet system, it will have no operation (although the Sekrit DSI & Majik DSI can be controlled by IR handset, but not play any Internet Radio get an music from the ethernet network).

Network cable check
  1. Power off the Linn DS/DSI
  2. Go to the backpanel of the Linn DS/DSI
  • monitor the Ethernet socket lights and power on the Linn DS/DSI
  • watch the Etherenet socket lights for approx 30 seconds,
Top
Network DHCP server check
  1. Power off the Linn DS/DSI again
  2. Now check the Linn DS/DSI front display and power on the Linn DS/DSI
  3. Linn DS/DSI ;
  • On the Sneaky-DS
  • Check the front panel Linn symbol power indicator light/LED
  • This should flash for between 5-30seconds, then come on permanently.
  • On the Sekrit-DSI
  • Check the front panel STBY light/LED
  • This should flash for between 5-30seconds, then extinquish and DHCP light should illuminate
  • On the remaining Linn DS/DSI products
  • Check the front panel display for a dot in the centre of the display
  • This should flash for between 5-30seconds, then be replaced by either the Standby display or source name


If on any of these Linn DS/DSI products, this light/dot keeps on flashing it is waiting to be given a network address from your Router/DHCP server.
The Linn DS/DSI know that the network is alive, (as with the previous test), so it is asking for an address so that it can enter your network, but it is not being provided with one. The DS/DSI will continuously ask, (flashing dot), until this happens. Suspect that your DHCP server/Router is not switch on or it has run out of addresses to give to network devices.

[Note: if the Linn DS/DSI does not have a live network connection, (none of the Ethernet socket lights flash), the flashing light/dot will stop flashing after between 5-30seconds and will not request a network address. The Linn DS/DSI will show a cross on its display to show that it has no address]


Network conneciton fault solutions

Loose network cable connecting the Linn DS/DSI to network device
  • Unplug and replug these connectors back into their sockets
Faulty network cable
  • Replace the CAT-5 ethernet cable
Network device, (switch, Router, homeplug), powered off
  • reconnect Mains and power connector to the network device



Network DHCP server/Router solutions

No connection to DHCP server/Router
  • Suspect that your Linn DS/DSI is connected to another ethernet device (Switch, Homeplug), to the DHCP server/Router. Check the ethernet cables are connected to the correct network sockets on these devices and the DHCP server/Router is powered on
There may not be any spare network addresses to connect any other devices to the network