Klimax ExaktBox

Getting Started

www.linn.co.uk/go/klimax

Product info

• Product Name: Klimax ExaktBox

• Date of Introduction: June 2014

• Type: Digital Crossover with Exakt Technology

Supports mono speakers from to 6-way

Software upgradable to support more and more loudspeakers

Connects to power amplifiers and externally Aktiv speakers

• Can only be used wit Exakt-Link output products

• Features
  • Dynamik Power Supply
  • Exakt Technology

Support

Linn Support Site

Latest software

Latest software releases

Open source software

Manuals

Konfig manual

Exakt Optimisation

Exakt Optimisation (Advanced)

Safety Information

Warranty Terms and Conditions

Back Panel Connections

1. MAINS INPUT - To connect to the mains electricity supply.
2. EXAKT LINK- To connect to Exakt compatible devices
3. BALANCED OUTPUT 1 - 6 - To connect to power amplifiers. (300ohm output impedance)
4. FALLBACK - To put the device into Fallback mode (used when reprogramming the unit).

LED Status

LED	OFF	ON	Flash / Blink
0 Master Port	No Link	Link Discovered	Link Activity
1 Audio Clock	No Clock	Clock locked	Clock not locked
2 Slave Port	No Link	Link Enabled	Link Activity
3 Software Status	Not Configured	Running	Hardware Fault

Power Amplifier/Speaker connections

DOUBLE CHECK the wiring from the Exaktbox to power amplifier to speaker terminals!
If there are any mis-wires or wrong speaker definintions in the Exaktbox, you may blow the speaker drive units, so take care.

If this is the first connection use the standard Aktiv test scenario.

1. Disconnect any power amplifier to speakers connections
2. Switch off ALL power amplifiers.
3. Set to a low volume value, e.g 40-50
4. Connect ONLY the Bass (or drive unit you are testiing shown in point7) power amplifier connection to the Bass connection (or drive unit you are testiing shown in point7) of the speaker.
5. Switch on the Bass amplifier and play some Music. Check that you are only getting Bass audio from that speaker drive unit.
6. Stop the Music playing.
7. Leave this cable connected and repeat steps 3-7 for each speaker individually in the order of

Bass, Midrange, tweeter and super-tweeter

To see the Exaktbox terminations for each speaker click here

If you have power amplifers with RCA/Phono terminations we suggest you use the follow setup.
ONLY use ALL XLR connections or ALL Phono/RCA connections to the power amplfiers. (The Klimax 350 and Komri internal amplifier is an XLR connection, you CAN use RCA/Phono or XLR amplifiers with these speakers configurations)

Installation

Please read the following carefully before installing the unit in your system – your unit may need to be reconfigured by your Linn retailer.

• Unpacking Information

• Positioning Information

• The ExaktBox is shipped from Linn with no speaker setup and must be configured with Konfig software.

Exakt options

Exakt usage can be found in Klimax_Exakt_System

One of the beneifts of the Exakt system is that you can easily setup and optimise your listening environment. Simply download the latest version of Konfig (version 4.11.7 or higher) and follow the Exakt Optimsation

Supported speakers

Currently available using one Klimax Exaktbox

• single Klimax / Artikulat 350
• single Akubarik passive
• single Akudorik passive
• single Akurate 242 mk2
• single Akurate 212 mk2
• single Komri
• single Keltik - Bass Bi-Amped
• pair Keltik - Bass Bi-wired
• pair Espek
• single Majik Isobarik
• single Majik 140

Coming Soon

• Akurate 242 mk1
• Akurate 212 mk1
• Majik 109
• Ninka
• Katan
• Kaber
• Keilidh

non-Linn speakers

Currently available

1. 2 x B&W Nautilus

For further assistance, try our customer support pages or the Linn Forum.