Template:ModuleInfo:SELEKT DSM CARTRIDGE - 1.1

SELEKT DSM CARTRIDGE - 1.1

Linn part#       SK CHH1
Description:
This is a module with a single line-level audio channel (2off RCA sharing the same audio) for the Sub(s) feed. Plus a single channel Power Amplifier outputs for Centre channel feed.
This is designed for a Centre channel (Power Amplifier) and Sub-woofer (RCA-Line Level) connection in a Surround system

This module has a standard-level 1 Digital to Analogue Convertor on both Power Amplifier and RCA outputs .

Line Output:
	Output Level:	2V rms @volume 80
	Output Impedance:	300Ω

Power Amplifier Output:

Bridged Class-D amplifier with post-filter feedback using 4mm/Banana plug terminals.

Max output power:

100W/channel into 4Ω load,

50W / channel into 8Ω load

Note:

• An upgrade to the Selekt Power supply may be requried to use any new modules.
• Power Amplifier outputs: These are CLASS-D amplifier outputs and speakers should ONLY be connected/disconnected when the product in is Sleep state or powered OFF.
  
• Some Electrostatic speakers may require a modification to work with Linn Class-D amplifier. Please refer to the speaker manufacturers website for information.
• The Selekt power amplfiers have a slightly lower gain than other Linn power amplifiers, (original Majik/Akurate..). If you are going to Bi-Amp a pair of speakers then we would recommend either ALL Selekt Power amplifier cartridges or ALL Selekt Line level cartridges with external amplifiers.

Description:

This is a module with 1off Class-D Power Amplifier channel

Each channel uses 4mm/Banana plug terminals

DAC - Digital to Analogue Convertor

Option 2:

Katalyst (Level-2)

Power Amplifier Output:

Bridged Class-D amplifier with post-filter feedback using 4mm/Banana/binding post terminals.

	Max output power:
		100W/channel into 4Ω load,
		50W / channel into 8Ω load
	THD+N:	0.001%
	Dynamic Range	110dB
	Gain:	20dB

Note:

• An upgrade to the Selekt Power supply may be requried to use any new modules.
• Power Amplifier outputs: These are CLASS-D amplifier outputs and speakers should ONLY be connected/disconnected when the product in is Sleep state or powered OFF.
  
• Some Electrostatic speakers may require a modification to work with Linn Class-D amplifier. Please refer to the speaker manufacturers website for information.
• The Selekt power amplfiers have a slightly lower gain than other Linn power amplifiers, (original Majik/Akurate..). If you are going to Bi-Amp a pair of speakers then we would recommend either ALL Selekt Power amplifier cartridges or ALL Selekt Line level cartridges with external amplifiers.
• DAC's are sold seperately and ONE DAC module MUST be fitted to the the cartridge to get audio from this cartridge.
• Different DAC's modules can be used with each Selekt Cartridge.

Either

• Standard (Level-1) Stereo DAC is the standard DAC.

or

• Katalyst (Level-2) Stereo DAC use the higher specification Katalyst DAC Architecture

or

• Organik (Level-3) Stereo or Mono DAC use the higher specification Organik DAC Architecture

• Only one type of DAC module can be installed in each cartridge.

That is, You CANNOT have a Standard and a Katalyst DAC module installed in the same Line-level, Power-amplifier or Hybrid 1.1 catridge at the same time.

• These Standard and Katalyst DAC modules are interchangeable in different cartridges in the same Selekt DSM.

However Organik DAC modules CANNOT be used with Standard and Katalyst DAC modules in different cartridges, in the same Selekt DSM

• The Organik MONO DACs can ONLY be used in the Mono Line Out Cartridge
• You CANNOT mix Organik Stereo cartridges with Organik Mono Line Out Cartridges

• Warning: Changing Selekt Cartidge(s) or Module(s).

Applies to: All Selekt DSM variants

To reduce the risk of damage to your Selekt DSM:

• The Selekt DSM MUST be disconnected from Mains power supply by BEFORE any cartridge(s) or module(s) are removed/Inserted.