Jump to content

Template:Setup:Selekt Edition Sub

From LinnDocs

Important: Sub Out limitations

  • Sub Out is active only during stereo playback, and only when the DSM's internal volume control is enabled.
  • Sub Out is not active during surround playback.
  • Do not use Sub Out with Exakt speakers or with speakers driven by Exakt filters. For these systems, use the Exaktbox-Sub instead (see below).

Sub Out is designed to enhance stereo playback on the Selekt DSM Edition and the Selekt DSM Classic/1. In this configuration, the outputs are used as follows:

  • Front L+R: the Selekt DSM output cartridges run in passthrough mode and feed the main speakers.
  • Sub Out: carries the subwoofer feed, using a configurable filter.

Why Sub Out is not compatible with Exakt: Exakt filters delay the signal to the main speakers by 45 ms. Sub Out does not apply the same delay, so the subwoofer would play 45 ms ahead of the main speakers and the two would not be time-aligned. For Exakt systems, use the Exaktbox-Sub, which handles the subwoofer within the Exakt signal path.

Examples

-


In Manage Systems - Output options
This is for use with Stereo playback only. If you have a Selekt cartridge configured for LFE Surround and your Subwoofer has two inputs, you can fed one input from the LFE output and the other Sub-woofer input from the SUBOUT output.
Subwoofer
Options:
* ENABLED to enable these back panel outputs.
* DISABLED to disable these back panel outputs.


Subwoofer Filter
  • Enabled SUBOUT L+R set by crossover frequency 60Hz, 80Hz, 120Hz .
  • Disabled SUBOUT L+R crossover frequency 1kHz, the LHC/RHC audio is flat.


Subwoofer Crossover Frequency
If Subwoofer filter is enabled:
  • 60 Crossover frequency 60Hz
  • 80 Crossover frequency 80Hz
  • 120 Crossover frequency 120Hz


Subwoofer Crossover Type
  • Bass redirect Audio above the Subwoofer Crossover Frequency frequency is sent to the F+R channels. (Audio below this frequency is redirected to the SUBOUT outputs.)
  • Bass Reinforcement Audio to the F+R channels is as a flat response.


Subwoofer Channels
  • Mono L+R subwoofer combined into one output.
  • Stereo separate LHC and RHC subwoofer outputs


Notes
  • Only works with Stereo playback
  • Only works correctly when the FL+FR speakers are from the Selekt Cartridge(s). It does not work reliably with Exakt connected loudspeakers.
  • Does NOT work with DSD playback
  • The output level is solely controlled by the Linn DSM volume control. Any Sub trim should be performed at the subwoofer. If the volume control is disabled then this output is also disabled.


Option for Subwoofer operation in both Stereo and Surround Playback

Applies to the Selekt DSM Edition and Selekt Classic DSM /1, which have a subwoofer output on the back panel.

If your subwoofer has two line inputs, it can play in both stereo and surround playback:

  1. Set up a Selekt cartridge output, or an ExaktBox, as the surround LFE channel.
  2. Set up the back-panel subwoofer output in Manage Systems.
  3. Connect the surround LFE channel to one input on the subwoofer.
  4. Connect the back-panel subwoofer output (either L or R) to the other input on the subwoofer.

The subwoofer then plays from the back-panel subwoofer output in stereo playback, and from the LFE channel in surround playback.

Example:

Example wiring with a subwoofer connected to both a cartridge LFE output and the Selekt DSM Edition back-panel subwoofer output