Difference between revisions of "Template:Issues@Linn DS/DSM"

From LinnDocs
Jump to: navigation, search
m (Created page with "====There is a ! on the front panel of my Linn DS/DSM==== There is a speaker setup issue on the Linn DS/DSM Surround Sound Rules <br><br> ====The fro…")
 
m
 
(One intermediate revision by the same user not shown)
Line 1: Line 1:
====There is a ! on the front panel of my Linn DS/DSM====
+
====The front panel of the DS is showing a flashing dot or lightening flash and I cannot see the Linn DS with Kazoo or Konfig====
There is a speaker setup issue on the Linn DS/DSM
 
[[Surround_Sound#Rules | Surround Sound Rules]]
 
 
 
<br><br>
 
 
 
====The front panel of the DS is showing a flashing dot or lightening flash and I cannot see the Linn DS with Kinsky or Konfig====
 
  
 
This is the Linn DS either in "'''startup'''" mode or in "'''Waiting for Software'''" mode. <br>
 
This is the Linn DS either in "'''startup'''" mode or in "'''Waiting for Software'''" mode. <br>
"'''Startup'''": The flashing dot is the startup mode trying to connect to you ethernet network. This mode will typically occur when you first apply power to the Linn DS/DSM. This will typically take 30seconds and go into standard use mode.<br>
+
:"'''Startup'''": The flashing dot is the startup mode trying to connect to you ethernet network. This mode will typically occur when you first apply power to the Linn DS/DSM. This will typically take 30seconds and go into standard use mode.<br>
 
'''
 
'''
"'''Waiting for Software'''": The lightening flash is the Linn DS/DSM waiting or getting a software update.
+
:"'''Waiting for Software'''": The lightening flash is the Linn DS/DSM waiting or getting a software update.
  
 
If you have any problems getting the Linn DS on an Ethernet network, (dot continuously flashing), try the following options:-
 
If you have any problems getting the Linn DS on an Ethernet network, (dot continuously flashing), try the following options:-

Latest revision as of 12:54, 15 October 2018

The front panel of the DS is showing a flashing dot or lightening flash and I cannot see the Linn DS with Kazoo or Konfig

This is the Linn DS either in "startup" mode or in "Waiting for Software" mode.

"Startup": The flashing dot is the startup mode trying to connect to you ethernet network. This mode will typically occur when you first apply power to the Linn DS/DSM. This will typically take 30seconds and go into standard use mode.

"Waiting for Software": The lightening flash is the Linn DS/DSM waiting or getting a software update.

If you have any problems getting the Linn DS on an Ethernet network, (dot continuously flashing), try the following options:- Option1

  • Power off the EVERYTHING connected to the Ethernet system, (PC, Printers, DS, Routers/DHCP servers).
  • Leave everything powered off for at least 10seconds.
  • Switch everything back on.
  • Retry the system

You will find that some of the devices in the system get confused and cause system confusion. The power cycling will do a reset of the system and recover most issues.

Option2

  • Use fresh Ethernet cables, (replace existing cables).
  • If the Linn Ds is more than 3M (10ft) from the DHCP/Server. Move the Linn DS right beside the Router/DHCP server and patch using a short Ethernet cable (1M), the Linn DS to the DHCP server/Router
  • Retry the system

Option3

  • Build a totally separate system with only a DHCP/Server and Linn DS.
  • Retry the system

Some networks only have a limited number of DHCP address’s. if you have already connected some PC’s to this system, your Router/DHCP server can remember these devices, (even though no longer connected) and will not allocated these previously assigned IP addresses to newly connected products. So the case of unplugging one device to free up an IP address for the DS to use will NOT work with most Routers/DHCP servers if there are no free DHCP IP addresses available.

This will give a better idea as to what is causing the problem. (98% of the time, this is due to a local network issue).

If you always get the flashing dot then the lightening flash symbol then the Linn DS/DSM needs to be programmed. Check the Konfig Manual > Updates section or contact your Linn Retailer to get assistance.