Difference between revisions of "HDMI Setup"

From LinnDocs
Jump to: navigation, search
(Stereo Mode)
m (Overview)
 
(67 intermediate revisions by 3 users not shown)
Line 1: Line 1:
The Davaar 5 software update introduces a number of new configuration parameters, relating to HDMI, for the Klimax DSM and Akurate DSM products.  These settings allow the products to be used as part of a multichannel system through interoperability with an external AV receiver.
+
==Overview==
 +
<font color="red">
 +
'''NOTE THIS IS ONLY APPLICABLE UP TO DAVAAR 37 DS FIRMWARE & HDMI-1 boards'''<br></font>
  
 +
The Davaar 50 > software update introduces a number of HDMI configuration parameters to the DSM  product range.  These settings allow some products to be used as part of a multichannel system through interoperability with an external AV receiver.<br>
 +
This is ONLY Surround setup is only compatable with Linn DSM products with '''HDMI1''' boards.
  
 
==Audio Mode==
 
==Audio Mode==
Line 10: Line 14:
 
[[Image:DSM_Stereo_Setup_Speakers.jpg|center|700px|Image:DSM Stereo Setup.jpg]]
 
[[Image:DSM_Stereo_Setup_Speakers.jpg|center|700px|Image:DSM Stereo Setup.jpg]]
  
Note: To allow the DSM to function correctly in '''Stereo''' mode, the HDMI output of the Source product (ex. BluRay player)''' should be configured to Auto or Stereo PCM'''. This setting can be found under '''HDMI audio settings''' in the setup menu of your HDMI source product. Please refer to the HDMI source product's user manual for instructions on how to do this.
+
In '''Stereo''' mode the DSM will '''not''' pass audio to its HDMI output (TV) while an  HDMI input is selected for listening.
  
=== Surround Mode ===
+
<font color="indigo">
In Surround mode the DSM can be used to play the two '''Front''' stereo channels (FL/FR), of an incoming HDMI multichannel audio stream, while passing the '''remaining''' channels on to the HDMI output to be played by an attached AV Receiver product. The diagram below shows how the various components of the multichannel system should be connected using '''Surround''' mode.
+
'''Note''': To allow the DSM to function correctly in '''Stereo''' mode, the HDMI output of the Source product (ex. BluRay player) '''must be configured to either Auto or Stereo PCM'''. This setting can be found under '''HDMI audio settings''' in the setup menu of your HDMI source product. Please refer to the HDMI source product's user manual for instructions on how to do this. </font>
 +
 
 +
=== Surround Mode *===
 +
This is identified by a multi-channel LPCM stream coming into the HDMI1 board. In Surround mode the DSM can be used to play the two '''Front''' stereo channels (FL + FR), of an incoming HDMI multichannel audio stream, while passing the '''remaining''' channels on to the HDMI output to be played by an attached AV Receiver product. The diagram below shows how the various components of the multichannel system should be connected using '''Surround''' mode.
  
 
[[Image:DSM_Surround_SetupSpeakers.jpg|center|700px|Image:DSM Surround Setup.jpg]]
 
[[Image:DSM_Surround_SetupSpeakers.jpg|center|700px|Image:DSM Surround Setup.jpg]]
  
Note: To allow the DSM to function correctly in '''Surround''' mode, the HDMI output of the Source product (ex. BluRay player)''' must be configured to output PCM'''. This setting can be found under '''HDMI audio settings''' in the setup menu of your HDMI source product. Please refer to the HDMI source product's user manual for instructions on how to do this.
+
In '''Surround ''' mode the DSM will '''only''' pass audio to its HDMI output (AV Receiver) when an HDMI input is selected for listening.
 +
 
 +
<font color="indigo">
 +
'''Note''': To allow the DSM to function correctly in '''Surround''' mode, the HDMI output of the Source product (ex. BluRay player)''' must be configured to output PCM'''. This setting can be found under '''HDMI audio settings''' in the setup menu of your HDMI source product. Please refer to the HDMI source product's user manual for instructions on how to do this.</font>
 +
 
 +
''''' * Surround Mode option is available on Klimax DSM, Klimax Exakt DSM, Akurate DSM, Akurate Exakt DSM and Majik DSM only.'''''
  
 
==Volume==
 
==Volume==
  
 
===Master Volume===
 
===Master Volume===
In Surround mode the DSM master volume is applied to all audio channels simultaneously allowing control from a single DSM handset or network control point.  
+
In '''Surround''' mode the DSM master volume is applied to all audio channels simultaneously allowing control from a single DSM handset or network control point. '''The volume of the AV Receiver should therefore be set to unity gain, or equivalent high value, for optimum results'''.
  
 
===AV Volume Offset===
 
===AV Volume Offset===
The AV Volume Offset setting allows compensation for small differences in volume between the DSM and AV Receiver products. A positive value will increase the volume of all audio channels passed to the AV receiver. A negative value will decrease the volume of audio channels passed to the AV receiver. '''AV Volume Offset''' is specified in dBs, ranging from '''-15''' to '''+15''' in '''0.5 dB''' steps. '''This setting is only applied when Audio Mode is set to Surround'''.
+
The AV Volume Offset setting allows compensation for small differences in volume between the DSM and AV Receiver products. A positive value will increase the volume of all audio channels passed to the AV receiver. A negative value will decrease the volume of audio channels passed to the AV receiver. '''AV Volume Offset''' is specified in dBs, ranging from '''-15''' to '''+15''' in '''0.5 dB''' steps. The default value is 0. '''This setting is only applied when Audio Mode is set to Surround'''.
 
 
  
 
==Delay==
 
==Delay==
 
===Lipsync===
 
===Lipsync===
In Surround mode, any delay (lipsync) that is being applied to the HDMI input by the DSM is applied to all audio channels simultaneously to ensure perfect synchronisation.
+
In Surround mode, any delay (lipsync) that is being applied to the HDMI input by the DSM is applied to all audio channels simultaneously to ensure perfect synchronisation. If the AV Receiver has its own lipsync setting this should be set to zero if possible.
 +
 
 
===AV Latency===
 
===AV Latency===
AV Latency setting allows compensation for any small latency (delay) that is being applied by the AV Receiver product. '''This setting is only applied when Audio Mode is set to Surround'''.
+
AV Latency allows the DSM to compensate for any small inherent hardware latency (delay) in the AV Receiver product. The value entered here is taken into account by the DSM when applying its lipsync delay to the audio channels sent to the AV receiver. '''AV Latency''' is specified in milliseconds (ms), ranging from '''0''' to '''100''' in '''1ms''' steps. The default value is 0. '''This setting is only applied when Audio Mode is set to Surround'''.
  
 
==Downmixing==
 
==Downmixing==
 
===Downmix Centre To Fronts===
 
===Downmix Centre To Fronts===
Downmix Centre To Fronts, when enabled, causes the centre channel audio content to be downmixed (redirected) to the front speaker channels. This setting should be enabled when there is '''no''' centre channel speaker present in the system. '''This setting is only applied when Audio Mode is set to Surround.'''
+
Downmix Centre To Fronts, when enabled, causes the '''centre''' channel audio content to be downmixed (redirected) to the '''Front''' speaker channels. This setting should be enabled when there is '''no centre''' speaker present in the system. '''This setting is only applied when Audio Mode is set to Surround.'''
  
 
===Downmix LFE To Fronts===
 
===Downmix LFE To Fronts===
Downmix LFE To Fronts, when enabled, causes the '''low frequency effects''' channel audio content to be downmixed (redirected) to the front speaker channels. This setting should be enabled when there is '''no''' LFE channel speaker present in the system. '''This setting is only applied when Audio Mode is set to Surround'''.
+
Downmix LFE To Fronts, when enabled, causes the '''low frequency effects''' channel audio content to be downmixed (redirected) to the '''Front''' speaker channels. This setting should be enabled when there is '''no subwoofer''' speaker present in the system. '''This setting is only applied when Audio Mode is set to Surround'''.
 +
 
 +
== Tested HDMI Players/Receivers ==
 +
 
 +
The following Receivers have been tested and shown to work. Note that the hardware and firmware of these devices is under the control of their respective manufacturers and may change from what was tested
 +
 
 +
* Yamaha RX-V671
 +
* Pioneer VSX-921
 +
* Anthem D2
 +
* ROTEL RSX 1562
 +
* ONKYO PR -SC5590
 +
* DENON AVR 3313
 +
 
 +
 
 +
Blu-Ray Players
 +
* OPPO BDP-93
 +
* Electrocompaniet EMP3
 +
* CAMBRIDGE AUDIO CXUHD
 +
 
 +
Check the Manufacturers specifications of any HDMI Receiver and look for Multichannel PCM support, (can also be called Linear PCM (LPCM))

Latest revision as of 07:49, 16 April 2019

Overview

NOTE THIS IS ONLY APPLICABLE UP TO DAVAAR 37 DS FIRMWARE & HDMI-1 boards

The Davaar 50 > software update introduces a number of HDMI configuration parameters to the DSM product range. These settings allow some products to be used as part of a multichannel system through interoperability with an external AV receiver.
This is ONLY Surround setup is only compatable with Linn DSM products with HDMI1 boards.

Audio Mode

Audio Mode can be set to Stereo or Surround. The default setting is Stereo.

Stereo Mode

In Stereo mode all Surround features are disabled. The diagram below shows how the various components of the system should be connected when using Stereo mode.

Image:DSM Stereo Setup.jpg

In Stereo mode the DSM will not pass audio to its HDMI output (TV) while an HDMI input is selected for listening.

Note: To allow the DSM to function correctly in Stereo mode, the HDMI output of the Source product (ex. BluRay player) must be configured to either Auto or Stereo PCM. This setting can be found under HDMI audio settings in the setup menu of your HDMI source product. Please refer to the HDMI source product's user manual for instructions on how to do this.

Surround Mode *

This is identified by a multi-channel LPCM stream coming into the HDMI1 board. In Surround mode the DSM can be used to play the two Front stereo channels (FL + FR), of an incoming HDMI multichannel audio stream, while passing the remaining channels on to the HDMI output to be played by an attached AV Receiver product. The diagram below shows how the various components of the multichannel system should be connected using Surround mode.

Image:DSM Surround Setup.jpg

In Surround mode the DSM will only pass audio to its HDMI output (AV Receiver) when an HDMI input is selected for listening.

Note: To allow the DSM to function correctly in Surround mode, the HDMI output of the Source product (ex. BluRay player) must be configured to output PCM. This setting can be found under HDMI audio settings in the setup menu of your HDMI source product. Please refer to the HDMI source product's user manual for instructions on how to do this.

* Surround Mode option is available on Klimax DSM, Klimax Exakt DSM, Akurate DSM, Akurate Exakt DSM and Majik DSM only.

Volume

Master Volume

In Surround mode the DSM master volume is applied to all audio channels simultaneously allowing control from a single DSM handset or network control point. The volume of the AV Receiver should therefore be set to unity gain, or equivalent high value, for optimum results.

AV Volume Offset

The AV Volume Offset setting allows compensation for small differences in volume between the DSM and AV Receiver products. A positive value will increase the volume of all audio channels passed to the AV receiver. A negative value will decrease the volume of audio channels passed to the AV receiver. AV Volume Offset is specified in dBs, ranging from -15 to +15 in 0.5 dB steps. The default value is 0. This setting is only applied when Audio Mode is set to Surround.

Delay

Lipsync

In Surround mode, any delay (lipsync) that is being applied to the HDMI input by the DSM is applied to all audio channels simultaneously to ensure perfect synchronisation. If the AV Receiver has its own lipsync setting this should be set to zero if possible.

AV Latency

AV Latency allows the DSM to compensate for any small inherent hardware latency (delay) in the AV Receiver product. The value entered here is taken into account by the DSM when applying its lipsync delay to the audio channels sent to the AV receiver. AV Latency is specified in milliseconds (ms), ranging from 0 to 100 in 1ms steps. The default value is 0. This setting is only applied when Audio Mode is set to Surround.

Downmixing

Downmix Centre To Fronts

Downmix Centre To Fronts, when enabled, causes the centre channel audio content to be downmixed (redirected) to the Front speaker channels. This setting should be enabled when there is no centre speaker present in the system. This setting is only applied when Audio Mode is set to Surround.

Downmix LFE To Fronts

Downmix LFE To Fronts, when enabled, causes the low frequency effects channel audio content to be downmixed (redirected) to the Front speaker channels. This setting should be enabled when there is no subwoofer speaker present in the system. This setting is only applied when Audio Mode is set to Surround.

Tested HDMI Players/Receivers

The following Receivers have been tested and shown to work. Note that the hardware and firmware of these devices is under the control of their respective manufacturers and may change from what was tested

  • Yamaha RX-V671
  • Pioneer VSX-921
  • Anthem D2
  • ROTEL RSX 1562
  • ONKYO PR -SC5590
  • DENON AVR 3313


Blu-Ray Players

  • OPPO BDP-93
  • Electrocompaniet EMP3
  • CAMBRIDGE AUDIO CXUHD

Check the Manufacturers specifications of any HDMI Receiver and look for Multichannel PCM support, (can also be called Linear PCM (LPCM))