Exakt Optimsation

From LinnDocs
Revision as of 14:20, 30 October 2013 by Hahnj21 (talk | contribs) (Stage 5: Fine Tune Filter Parameters to Improve Audio Performance)
Jump to: navigation, search

Introduction

Exakt Optimisation provides a listener focused view of room optimisation. This means that Exakt compatible products give the listener an opportuinty to greatly improve the listening experience by providing the Exakt products with information about the listening environment. The software inside the Exakt products can then account for the listening environment and compenstate accordingly.

Overview

Konfig can optimise for the following acoustic phenomena:

Room Modes

Every room is different, and can therefore be optimised to sound as good as possible. You will need to use the TuneDem method to find the ideal location for your speakers.

Speaker Placement

In practice, the ideal TuneDem location for your speakers is rarely the practical location as well. Not to worry, optimisation will allow the ideal Tune Dem sound to be applied wherever your speakers are located.

High Frequency Response

Each room responds to high frequency (a.k.a. treble) differently. An empty room with marble walls will respond much differntly to a room with plasterboard walls and lots of soft furnishings. This stage allows you to optimise according to the high frequency response of your room.

Optimisation Process

Stage 1: TuneDem

  1. Using the TuneDem method, deterimine the ideal speaker location for your room
  2. Once you have completed the TuneDem, select your Exakt device in Konfig
  3. Click on the Exakt Optimisation tab

File:KonfigExaktTabs.jpg

Stage 2: Optimise for Room Modes

File:KonfigExaktOptimisationRoomModesDimensions.jpg

  1. Click on the Room Modes optimisation tab.
  2. Enter values for Room Dimensions, Listening Position, and Ideal TuneDem Speaker Position in the dimension form. See the diagram below for measurement references (all dimensions must be measured in meters). Click on Change Dimensions if you can not see the dimension form.
  3. Once all dimensions have been entered, click Optimise. You will then be presented with the room optimisation graph (Room Modes are in red).
  4. Clicking Disable will remove any Room Mode optimistaion from your setup.

RoomMeasurement

Stage 3: Optimise for Speaker Placement

File:KonfigExaktOptimisationSpeakerPlacementDimensions.jpg

  1. Click on the Speaker Placement optimisation tab.
  2. Enter values for Practical Speaker Position in the dimension form. See the diagram below for measurement references (all dimensions must be measured in meters). Click on Change Placement if you can not see the dimension form.
  3. Once all dimensions have been entered, click Optimise. You will then be presented with the room optimisation graph (Speaker Placement is in red).
  4. Clicking Disable will remove any Speaker Placement optimistaion from your setup.

RoomMeasurement

Stage 4: Optimise for High Frequency Response

File:KonfigExaktOptimisationHighFrequencyResponse.jpg

  1. Click on the High Frequency Response optimisation tab.
  2. You are presented with the room optimisation graph (High Frequency Response is in red).
  3. This stage is the equivalent of a treble shelf.
  4. Enter frequency and gain values as required.
  5. To disable any high frequency response, set the gain to 0.

Stage 5: Fine Tune Filter Parameters to Improve Audio Performance

  1. Select the corresponding optimisation tab (Room Modes, Speaker Placement, or High Frequency Response)
  2. Each notch filter in the room optimisation graph is represented by a Room Mode (i.e. Room Mode 1, Room Mode 2, etc)
  3. You can modify a notch filter by selecting it from the drop down box and entering new values.

RoomMeasurement

Changing the Frequency value will shift the notch left or right along the x-axis.
Changing the Gain value will change the height of the notch.
Changing the Bandwidth value with change the width of the notch