Sekrit DSM

Product info

• Product Name: Sekrit DSM

• Date of Introduction: December 2012

• Type: Integrated digital music player, pre-amplifier, and power amplifier

• Dimensions: 345 mm (width) x 44 mm (height) x 196.5mm (depth)

• Features
  • DS Design
  • Source Unity Gain option

Support

Linn Support Site

Latest software

Latest software releases

Open source software

Manuals

Konfig manual

Kinsky Desktop manual

DSM Remote control manual

Safety Information

Warranty Terms and Conditions

HDMI Setup

HDMI Setup

Network Setup

DS Budget System Setup

DS Entry Level System Setup

DS High End System Setup

Back Panel Connections

1. MAINS INPUT - To connect to the mains electricity supply.
2. FALLBACK- To put the device into Fallback mode (used when reprogramming).
3. ETHERNET - To connect to a network.
4. HDMI OUTPUT - To connect to a display device with HDMI inputs.
5. HDMI INPUTS - To connect sources with HDMI outputs.
6. ANALOGUE OUTPUT (RCA, variable/fixed level) - To connect to subwoofer or external power amplifier (or pre amplifier when internal volume control is disabled, this will also disable the internal Power amplifier/speaker outputs) with unbalanced (RCA) analogue inputs.
7. IR OUTPUTS - To connect to infrared flasher devices allowing control of other products that accept infra-red signals.
8. DIGITAL INPUT (Toslink) - To connect sources with Toslink (optical) digital outputs.
9. DIGITAL INPUT (Spdif) - To connect sources with Spdif (RCA) digital outputs.
10. ANALOGUE INPUT (line level) - To connect a turntable or line level source with unbalanced (RCA) outputs.
11. SPEAKER OUTPUTS - To connect to loudspeakers, Neutrik 4 pole connector
12. RC5 ACCESSORY - To connect BASIK-3 & BASIK-3IR Room Control units.

Front Panel Connections

1. IR SENSOR - Recieves IR commands
2. DIAGNOSTIC LEDS - See table below for functionality
3. FALLBACK (F-BACK) - To put the device into Fallback mode (used when reprogramming).
4. POWER SWITCH- Switches the power on/off
5. IR REPEATER CLAMP- IR Repeater Clamp fixing screws

DIAGNOSTIC LED FUNCTIONS

Text	ON indicates	OFF indicates	Slow Flash / Blink	Fast Flash
IR	Pulse on IR command received	Reserved for future use	Reserved for future use	n/a
P-AMP	Internal amplifier enabled	Internal amplifier disabled	Internal amplifier fault	n/a
AUDIO	Valid audio (digital inputs only)	n/a	Invalid audio (digital inputs only)	n/a
DHCP	DHCP IP address obtained	Default IP address obtained	n/a	n/a
LINK	Ethernet link established	no link established	n/a	n/a
STBY	Device in standby	Device active	Searching for IP address (boot)	Fallback (reprogramme)

*NOTE: All LED's will flash if 'Locate Device' request is invoked from Konfig

Speaker Wiring

The Sekrit DSM has 4 DAC channels and 4 Power Amplifiers. These amplifiers can be configured in single ended mode or bridged mode.

Connections to the speakers are made via Neutrik Speakon connectors, NL4FX. Neutrik Speakon Assembly Instructions

The single ended mode is best suited to bi-amping a pair of passive speakers or for driving multiple pairs of loadspeakers. Bridged mode is best suited to driving a single pair of loudspeakers.

The wiring details are shown below:

• 33W/channel in single-ended mode
• 50W/channel in bridged mode

Installation

Please read the following carefully before installing the unit in your system – your unit may need to be reconfigured by your Linn retailer.

• Unpacking Information

• Positioning Information

• Amplifier Protection

For further assistance, try our customer support pages or the Linn Forum.