Difference between revisions of "Sekrit DSM"
(→Back Panel Connections) |
(→Back Panel Connections) |
||
| Line 61: | Line 61: | ||
# '''HDMI OUTPUT''' - To connect to a display device with HDMI inputs. | # '''HDMI OUTPUT''' - To connect to a display device with HDMI inputs. | ||
# '''HDMI INPUTS''' - To connect sources with HDMI outputs. | # '''HDMI INPUTS''' - To connect sources with HDMI outputs. | ||
| + | # '''ANALOGUE OUTPUT''' (RCA, variable/fixed level) - To connect to subwoofer or external power amplifier. | ||
| + | # '''IR OUTPUTS''' - To connect to infrared flasher devices allowing control of other products that accept infra-red signals. | ||
# '''DIGITAL INPUT''' (Toslink) - To connect sources with Toslink (optical) digital outputs. | # '''DIGITAL INPUT''' (Toslink) - To connect sources with Toslink (optical) digital outputs. | ||
# '''DIGITAL INPUT''' (Spdif) - To connect sources with Spdif (RCA) digital outputs. | # '''DIGITAL INPUT''' (Spdif) - To connect sources with Spdif (RCA) digital outputs. | ||
| Line 67: | Line 69: | ||
# '''ANALOGUE OUTPUT''' (RCA, variable/fixed level) - To connect to a preamplifier (or power amplifier when internal volume control is enabled) with unbalanced (RCA) analogue inputs. | # '''ANALOGUE OUTPUT''' (RCA, variable/fixed level) - To connect to a preamplifier (or power amplifier when internal volume control is enabled) with unbalanced (RCA) analogue inputs. | ||
# '''RC5 ACCESSORY''' - To connect BASIK-3 & BASIK-3IR Room Control units. | # '''RC5 ACCESSORY''' - To connect BASIK-3 & BASIK-3IR Room Control units. | ||
| − | |||
| − | |||
<br> | <br> | ||
Revision as of 10:15, 10 December 2012
Contents
Product info
- Product Name: Sekrit DSM
- Date of Introduction: December 2012
- Type: Integrated digital music player, pre-amplifier, and power amplifier
- Features
Support
Latest software
Manuals
HDMI Setup
Network Setup
Speaker Wiring
- 30W/channel in single-ended mode
- 50W/channel in bridhed mode
Back Panel Connections
- MAINS INPUT - To connect to the mains electricity supply.
- FALLBACK- To put the device into Fallback mode (used when reprogramming).
- ETHERNET - To connect to a network.
- HDMI OUTPUT - To connect to a display device with HDMI inputs.
- HDMI INPUTS - To connect sources with HDMI outputs.
- ANALOGUE OUTPUT (RCA, variable/fixed level) - To connect to subwoofer or external power amplifier.
- IR OUTPUTS - To connect to infrared flasher devices allowing control of other products that accept infra-red signals.
- DIGITAL INPUT (Toslink) - To connect sources with Toslink (optical) digital outputs.
- DIGITAL INPUT (Spdif) - To connect sources with Spdif (RCA) digital outputs.
- ANALOGUE INPUT (line level) - To connect a turntable or line level source with unbalanced (RCA) outputs.
- SPEAKER OUTPUTS - To connect to loudspeakers
- ANALOGUE OUTPUT (RCA, variable/fixed level) - To connect to a preamplifier (or power amplifier when internal volume control is enabled) with unbalanced (RCA) analogue inputs.
- RC5 ACCESSORY - To connect BASIK-3 & BASIK-3IR Room Control units.
Front Panel Connections
- IR SENSOR - Recieves IR commands
- DIAGNOSTIC LEDS - See table below for functionality
- FALLBACK (F-BACK) - To put the device into Fallback mode (used when reprogramming).
- POWER SWITCH- Switches the power on/off
DIAGNOSTIC LED FUNCTIONS
|
Text |
ON indicates |
OFF indicates |
Slow Flash / Blink |
Fast Flash |
| IR | Pulse on IR command received | Reserved for future use | Reserved for future use | n/a |
| P-AMP | Internal amplifier enabled | Internal amplifier disabled | Internal amplifier fault | n/a |
| AUDIO | Valid audio (digital inputs only) | n/a | Invalid audio (digital inputs only) | n/a |
| DHCP | DHCP IP address obtained | Default IP address obtained | n/a | n/a |
| LINK | Ethernet link established | no link established | n/a | n/a |
| STBY | Device in standby | Device active | Searching for IP address (boot) | Fallback (reprogramme) |
*NOTE: All LED's will flash if 'Locate Device' request is invoked from Konfig
Installation
Please read the following carefully before installing the unit in your system – your unit may need to be reconfigured by your Linn retailer.
For further assistance, try our customer support pages or the Linn Forum.
