Difference between revisions of "HDMI Setup"
(Blanked the page) |
|||
| Line 1: | Line 1: | ||
| + | The Davaar 5 software update introduces a number of new configuration parameters, relating to HDMI, for the Klimax DSM and Akurate DSM products. These settings allow the products to be used as part of a multichannel system through interoperability with an external AV receiver. | ||
| + | |||
| + | ==Audio Mode== | ||
| + | Audio Mode can be set to Stereo or Surround. The default setting is Stereo. In Stereo mode all Surround features are '''disabled'''. The diagram below shows how the various components of the system should be connected when using Stereo mode. | ||
| + | |||
| + | [[Image:DSM_Stereo_Setup.jpg|center|700px|Image:DSM Stereo Setup.jpg]] | ||
| + | |||
| + | |||
| + | In Surround mode the DSM can be used to play the two '''Front''' stereo channels (FL/FR), of an incoming HDMI multichannel audio stream, while passing the '''remaining''' channels on to the HDMI output to be played by an attached AV Receiver product. The diagram below shows how the various components of the multichannel system should be connected using Surround mode. | ||
| + | |||
| + | |||
| + | [[Image:DSM_Surround_Setup.jpg|center|700px|Image:DSM Surround Setup.jpg]] | ||
| + | |||
| + | Note: To allow the DSM to function correctly in Surround mode, the HDMI output of the Source product (ex. BluRay player) must be configured to output PCM. This setting can be found under HDMI audio settings in the setup menu of your HDMI source product. Please refer to the HDMI source product's user manual for instructions on how to do this. | ||
| + | |||
| + | |||
| + | ==Volume== | ||
| + | |||
| + | In Surround mode the DSM master volume is applied to all audio channels simultaneously allowing control from a single DSM handset or network control point. | ||
| + | |||
| + | ===AV Volume Offset=== | ||
| + | In Surround mode | ||
| + | |||
| + | |||
| + | ==Delay== | ||
| + | |||
| + | In Surround mode, any delay (lipsync) that is being applied to the HDMI input by the DSM is applied to all audio channels simultaneously to ensure perfect synchronisation. | ||
| + | |||
| + | |||
| + | ===AV Latency=== | ||
| + | |||
| + | |||
| + | ==Downmixing== | ||
| + | |||
| + | ===Downmix Centre To Fronts=== | ||
| + | Enable this setting to downmix the centre channel audio content to the front speaker channels. This setting should be enabled if a centre channel speaker is '''not''' present in the system. | ||
| + | |||
| + | ===Downmix LFE To Fronts=== | ||
| + | Enable this setting to downmix the low frequency effect channel audio content to the front speaker channels. This setting should be enabled if a subwoofer speaker is '''not''' present in the system. | ||
Revision as of 14:42, 19 December 2011
The Davaar 5 software update introduces a number of new configuration parameters, relating to HDMI, for the Klimax DSM and Akurate DSM products. These settings allow the products to be used as part of a multichannel system through interoperability with an external AV receiver.
Contents
Audio Mode
Audio Mode can be set to Stereo or Surround. The default setting is Stereo. In Stereo mode all Surround features are disabled. The diagram below shows how the various components of the system should be connected when using Stereo mode.
In Surround mode the DSM can be used to play the two Front stereo channels (FL/FR), of an incoming HDMI multichannel audio stream, while passing the remaining channels on to the HDMI output to be played by an attached AV Receiver product. The diagram below shows how the various components of the multichannel system should be connected using Surround mode.
Note: To allow the DSM to function correctly in Surround mode, the HDMI output of the Source product (ex. BluRay player) must be configured to output PCM. This setting can be found under HDMI audio settings in the setup menu of your HDMI source product. Please refer to the HDMI source product's user manual for instructions on how to do this.
Volume
In Surround mode the DSM master volume is applied to all audio channels simultaneously allowing control from a single DSM handset or network control point.
AV Volume Offset
In Surround mode
Delay
In Surround mode, any delay (lipsync) that is being applied to the HDMI input by the DSM is applied to all audio channels simultaneously to ensure perfect synchronisation.
AV Latency
Downmixing
Downmix Centre To Fronts
Enable this setting to downmix the centre channel audio content to the front speaker channels. This setting should be enabled if a centre channel speaker is not present in the system.
Downmix LFE To Fronts
Enable this setting to downmix the low frequency effect channel audio content to the front speaker channels. This setting should be enabled if a subwoofer speaker is not present in the system.
