Difference between revisions of "WIP/test create"
(Created page with "__NOINDEX__ {{:Page:Under_Construction}} right __TOC__ == '''Product Information''' == * ''Product Name:'' KEEL SE * ''Date of Introduction...") |
m |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
__NOINDEX__ | __NOINDEX__ | ||
{{:Page:Under_Construction}} | {{:Page:Under_Construction}} | ||
| − | + | {{HIDE_PAGE_TITLE}}{{:Tab-dropdown:Radikal_variants}} | |
| − | [[Image: | + | <!-- |
| − | + | {{Title_Text | LP12 Radikal (2025 variant)<br>}} [[Image:Klimax_Radikal.png |right|200px]] [[Image:Akurate_Radikal.png |right|200px]] | |
| + | __toc__ | ||
== '''Product Information''' == | == '''Product Information''' == | ||
| − | * ''Product Name:'' | + | * ''Product Name:'' Radikal (2025 variant) |
* ''Date of Introduction:'' Oct 2025 | * ''Date of Introduction:'' Oct 2025 | ||
| − | * ''Type:'' Turntable | + | * ''Type:'' Turntable power supply |
| + | |||
| + | <br> | ||
| + | ''Features:'' | ||
| + | :* FPGA-managed motor control unit (MCU) Power supply for LP12 | ||
| + | :* Bespoke [[Utopik]] Power supply for Urika / [[Urika_II]] | ||
| + | :* Supplied with DC motor for LP12 | ||
| + | :* Precision D to A Speed management system checks speed on every rotation | ||
| + | :* Dual speed: 33/45 rpm | ||
| + | <br> | ||
| + | |||
| + | '' Dimensions of power supply module:'' | ||
| + | ;Klimax Radikal | ||
| + | :: '''H''' 88.5mm x '''W''' 350mm x '''D''' 352mm | ||
| + | :: '''H''' 3.5" x '''W''' 13.8" x '''D''' 13.9" | ||
| + | :''These dimensions are <u>WITHOUT</u> power connectors fitted'' | ||
| + | |||
| + | == '''Support''' == | ||
| − | + | [http://www.linn.co.uk/support Linn Support Site] | |
| − | : | ||
| − | |||
| − | |||
| + | == '''Operation''' == | ||
| + | {{Manual:Radikal Operation}} | ||
| − | |||
| − | |||
| − | |||
| − | |||
| + | [http://docs.linn.co.uk/wiki/images/1/1b/Linn_Safety_Info.pdf Safety Information] | ||
| + | [http://www.linn.co.uk/warranty Warranty Terms and Conditions] | ||
== '''Installation''' == | == '''Installation''' == | ||
| − | Your | + | Your Linn Radikal will need to be installed and configured by your Linn retailer. |
| + | ;Note | ||
| + | : The motor used with the Radikal (2009 variant) and Radikal II (2021 variant) are different and not interchangeable, therefore an LP12 that has been installed with a Radikal (2009 variant) motor needs to have this replaced to work with a Radikal II (2021 variant). | ||
| + | |||
| + | :The motor used with the Radikal II (2021 variant) is identifiable by the blue band around the Neutrik connector. | ||
| + | |||
| − | + | ;Fault Detection | |
| − | + | :If the blue power LED on the front of the Radikal II is flashing, this means that a fault has been detected. This can indicate one of two faults: | |
| − | + | :: The motor is not properly connected | |
| − | + | :: The tachometer (speed sensor) board is not properly connected | |
| − | + | : Check the wiring for both | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| + | ;Factory reset | ||
| + | :To factory reset, | ||
| + | ::# Hold the button on the deck and | ||
| + | ::# Press the mode switch on the back of the radikal once. | ||
| + | :The radikal will wipe it's flash memory, restart and program the factory default values. | ||
| + | ---> | ||
For further assistance, try our [http://www.linn.co.uk/linn_customer_support customer support] pages | For further assistance, try our [http://www.linn.co.uk/linn_customer_support customer support] pages | ||
Latest revision as of 14:08, 9 October 2025
Webpage under construction
The information on this page may be incorrect and will be updated before release.
Linn Radikal variants:
For further assistance, try our customer support pages
