Difference between revisions of "Sneaky Music DS"

From LinnDocs
Jump to: navigation, search
(Back Panel Connections)
(Back Panel Connections)
Line 60: Line 60:
 
# '''DIGITAL OUT''' (TOSLINK) - To connect to an external DAC or computer that has a Toslink (optical) digital input.
 
# '''DIGITAL OUT''' (TOSLINK) - To connect to an external DAC or computer that has a Toslink (optical) digital input.
 
# '''DIGITAL OUT''' (SPDIF) - To connect to an external DAC or computer that has an Spdif digital input.
 
# '''DIGITAL OUT''' (SPDIF) - To connect to an external DAC or computer that has an Spdif digital input.
# '''RCU ACCESSORY''' - To connect to a Linn BASIK3 or BASIK3-IR Knekt control device.
+
# '''RCU ACCESSORY''' - To connect to a Linn BASIK3 or BASIK3-IR Knekt control device. This requires a Knekt-CAT-5 cable to operate NOT a
 
# '''RS232 PORTS''' - To connect to other Linn devices that don't have ethernet.
 
# '''RS232 PORTS''' - To connect to other Linn devices that don't have ethernet.
 
# '''FALLBACK''' - To put the device into Fallback mode (used when reprogramming)
 
# '''FALLBACK''' - To put the device into Fallback mode (used when reprogramming)

Revision as of 15:11, 3 October 2013

SneakyMusicDS Silv 3QRight RGB 72DPI.jpg

Product info

  • Product Name: Sneaky Music DS
  • Date of Introduction: March 2008
  • Type: Digital music player

Support

Linn Support Site

Latest software

Latest software releases

Open source software

Manuals

Product Information Sheet

Owners Manual

Setup Manual

Konfig manual

Kinsky Desktop manual

Remote Control manual

Kinsky Jukebox manual

Safety Information

Warranty Terms and Conditions

Network Setup

DS Budget System Setup

DS Entry Level System Setup

DS High End System Setup

Back Panel Connections

Sneaky DS rear.jpg
  1. MAINS INPUT - To connect to the mains electricity supply.
  2. EARTH GROUND - To connect to an earthing terminal if no mains earth is available or to join to the earths of other products in the system to improve performance in areas of poor/noisy electrical earth conditions.
  3. SPEAKER OUTPUTS - To connect to loudspeakers
  4. ANALOGUE OUTPUTS (RCA, variable/fixed level) - To connect to a preamplifier (or power amplifier when internal volume control is enabled) with unbalanced (RCA) analogue inputs.
  5. DIGITAL OUT (TOSLINK) - To connect to an external DAC or computer that has a Toslink (optical) digital input.
  6. DIGITAL OUT (SPDIF) - To connect to an external DAC or computer that has an Spdif digital input.
  7. RCU ACCESSORY - To connect to a Linn BASIK3 or BASIK3-IR Knekt control device. This requires a Knekt-CAT-5 cable to operate NOT a
  8. RS232 PORTS - To connect to other Linn devices that don't have ethernet.
  9. FALLBACK - To put the device into Fallback mode (used when reprogramming)
  10. ETHERNET - To connect to a network.


Front Panel Connections

SneakyMusicDS Silv Front RGB 72DPI.jpg

Product status is indicated by the LED behind the Linn badge, default settings are shown below.

LED OFF - no power
LED ON DIM - product in standby
LED ON BRIGHT - product is active
LED SLOW FLASH - searching for IP address (boot)
LED FAST FLASH - fallback (re-programme)

Note: LED may be turned off using Linn Konfig.

Installation

Please read the following carefully before installing the unit in your system – your unit may need to be reconfigured by your Linn retailer.

For further assistance, try our customer support pages or the Linn Forum.