Sneaky DSM

From LinnDocs
Revision as of 11:56, 7 February 2013 by Hahnj21 (talk | contribs) (Back Panel Connections)
Jump to: navigation, search
SneakyDsmFront.png

Product info

  • Product Name: Sneaky DSM
  • Date of Introduction: February 2012
  • Type: Integrated digital music player, pre-amplifier, and power amplifier
  • Dimensions: 350 mm (width) x 54.5 mm (height) x 215 mm (depth)

Support

Linn Support Site

Latest software

Latest software releases

Open source software

Manuals

Konfig manual

Kinsky Desktop manual

DSM Remote control manual

Safety Information

Warranty Terms and Conditions

HDMI Setup

HDMI Setup

Network Setup

DS Budget System Setup

DS Entry Level System Setup

DS High End System Setup

Back Panel Connections

SneakyDsmRear.png
  1. MAINS INPUT - To connect to the mains electricity supply.
  2. FALLBACK- To put the device into Fallback mode (used when reprogramming).
  3. ETHERNET - To connect to a network.
  4. HDMI OUTPUT - To connect to a display device with HDMI inputs.
  5. HDMI INPUTS (3) - To connect sources with HDMI outputs.
  6. ANALOGUE OUTPUT (RCA, variable/fixed level) - To connect to subwoofer or external power amplifier (or pre amplifier when internal volume control is disabled, this will also disable the internal Power amplifier/speaker outputs) with unbalanced (RCA) analogue inputs.
  7. DIGITAL INPUT (Toslink) - To connect sources with Toslink (optical) digital outputs.
  8. DIGITAL INPUT (Spdif) - To connect sources with Spdif (RCA) digital outputs.
  9. ANALOGUE INPUT (line level) - To connect a turntable or line level source with unbalanced (RCA) outputs.
  10. SPEAKER OUTPUTS - To connect to loudspeakers, Neutrik 4 pole connector


Front Panel Connections

SneakyDsmFront.png
  1. IR SENSOR - Recieves IR commands
  2. DIAGNOSTIC LEDS - See table below for functionality
  3. FALLBACK (F-BACK) - To put the device into Fallback mode (used when reprogramming).
  4. POWER SWITCH- Switches the power on/off
  5. IR REPEATER CLAMP- IR Repeater Clamp fixing screws


DIAGNOSTIC LED FUNCTIONS

Text

ON

indicates

OFF

indicates

Slow Flash / Blink

Fast Flash

IR Pulse on IR command received Reserved for future use Reserved for future use n/a
AMP Internal amplifier enabled Internal amplifier disabled Internal amplifier fault n/a
AUDIO Valid audio (digital inputs only) n/a Invalid audio (digital inputs only) n/a
IP DHCP IP address obtained Default IP address obtained n/a n/a
NET Ethernet link established no link established n/a n/a
STBY Device in standby Device active Searching for IP address (boot) Fallback (reprogramme)


Speaker Wiring

The Sekrit DSM has 4 DAC channels and 4 Power Amplifiers. These amplifiers can be configured in single ended mode or bridged mode. All speaker outputs (and Analogue Output) share the same common Volume control.

Connections to the speakers are made via Neutrik Speakon connectors, NL4FX. Neutrik Speakon Assembly Instructions

The single ended mode is best suited to bi-amping a pair of passive speakers or for driving multiple pairs of loadspeakers. Bridged mode is best suited to driving a single pair of loudspeakers.

The wiring details are shown below:

SekritDsmWiring.jpg


  • 33W/channel in single-ended mode
  • 50W/channel in bridged mode


Installation

Please read the following carefully before installing the unit in your system – your unit may need to be reconfigured by your Linn retailer.


For further assistance, try our customer support pages or the Linn Forum.