Difference between revisions of "Sekrit DS-I"

From LinnDocs
Jump to: navigation, search
(Manuals)
(Manuals)
Line 34: Line 34:
 
[http://docs.linn.co.uk/wiki/images/1/1b/Linn_Safety_Info.pdf Safety Information]
 
[http://docs.linn.co.uk/wiki/images/1/1b/Linn_Safety_Info.pdf Safety Information]
  
[http://www.linn.co.uk/warranty On-line warranty registration]
+
[http://www.linn.co.uk/warranty Warranty Terms and Conditions]
  
 
== '''Network Setup''' ==
 
== '''Network Setup''' ==

Revision as of 10:57, 28 November 2011

Sekrit DS-I front rightl RGB 72DPI.jpg

Product info

  • Product Name: Sekrit DS-I
  • Date of Introduction: October 2009
  • Type: Digital music player

Latest software

Latest software releases

Open source software

Manuals

Product Information

Konfig manual

Kinsky Desktop manual

Remote Control manual

Kinsky Jukebox manual

Safety Information

Warranty Terms and Conditions

Network Setup

Back Panel Connections

Image:Sekrit_DSI_rear.jpg


  1. MAINS INPUT - To connect to the mains electricity supply.
  2. EARTH GROUND - To connect to an earthing terminal if no mains earth is available or to join to the earths of other products in the system to improve performance in areas of poor/noisy electrical earth conditions.
  3. SPEAKER OUTPUTS - To connect to loudspeakers.
  4. ANALOGUE OUTPUTS (RCA, variable/fixed level) - To connect to a preamplifier (or power amplifier when internal volume control is enabled) with unbalanced (RCA) analogue inputs.
  5. ANALOGUE INPUTS (RCA, line level) - To connect sources with unbalanced (RCA) analogue outputs.
  6. RC5 ACCESSORY - To coonect BASIK-3 & BASIK-3IR Room Control units
  7. IR OUTPUTS - To connect to infrared flasher devices allowing control of other products that accept infra-red signals.
  8. RS232 PORTS - To connect to other Linn devices that don't have ethernet.
  9. ETHERNET - To connect to a network.
  10. DIGITAL INPUT (Spdif) - To connect sources with Spdif (RCA) digital outputs.
  11. DIGITAL INPUT (Toslink) - To connect sources with Toslink (optical) digital outputs.


Front Panel Connections

Image:Sekrit_DSI_front.jpg


  1. POWER SWITCH - Switches the power on/off
  2. FALLBACK BUTTON - To put the device into Fallback mode (used when reprogramming)


LED FUNCTIONS

Text

ON

indicates

OFF

indicates

Slow Flash / Blink

Fast Flash

STANDBY Device in standby Device active Searching for IP address (boot) Fallback (reprogramme)
LINK Ethernet link established no link established n/a n/a
DHCP DHCP IP address obtained Default IP address obtained n/a n/a
AUDIO Valid audio (digital inputs only) n/a Invalid audio (digital inputs only) n/a
POWER AMP Internal amplifier enabled Internal amplifier disabled Internal amplifier fault n/a
RCU Reserved for future use Reserved for future use Reserved for future use n/a
SEARCH n/a n/a Find me n/a
TRANSMIT Reserved for future use n/a n/a n/a


Installation

Please read the following carefully before installing the unit in your system – your unit may need to be reconfigured by your Linn retailer.

  • Unpacking - Please read the information on unpacking your Sekrit DS-I.
  • Positioning - Please read the information on positioning your Sekrit DS-I.
  • Important Information:Protection - The Sekrit DS-I features over-current and over-temperature protection

For further assistance, try our customer support pages or the Linn Forum.