Difference between revisions of "Sekrit DS-I"

From LinnDocs
Jump to: navigation, search
(Product info)
(Product info)
Line 5: Line 5:
 
* ''Product Name:'' Sekrit DS-I
 
* ''Product Name:'' Sekrit DS-I
  
* ''Date of Introduction:'' October 2009 (replaced by [[Sekrit_DSM|Sekrit DSM]] in 2013)
+
* ''Date of Introduction:'' October 2009
 +
* ''Discontinued: 2013'' - replaced by the [[Sekrit_DSM|Sekrit DSM]]
  
  

Revision as of 08:41, 7 December 2016

Sekrit DS-I front rightl RGB 72DPI.jpg

Product info

  • Product Name: Sekrit DS-I
  • Date of Introduction: October 2009
  • Discontinued: 2013 - replaced by the Sekrit DSM


  • Type: Digital music player

Support

Linn Support Site

Latest software

Latest software releases

Open source software

Manuals

Product Information

Konfig manual

Kinsky Desktop manual

Remote Control manual

Kinsky Jukebox manual

Space Optimisation+

Space Optimisation (Advanced)

Safety Information

Warranty Terms and Conditions

Network Setup

DS Budget System Setup

DS Entry Level System Setup

DS High End System Setup

Back Panel Connections

Image:Sekrit_DSI_rear.jpg


  1. MAINS INPUT - To connect to the mains electricity supply.
  2. EARTH GROUND - To connect to an earthing terminal if no mains earth is available or to join to the earths of other products in the system to improve performance in areas of poor/noisy electrical earth conditions.
  3. SPEAKER OUTPUTS - To connect to loudspeakers.
  4. ANALOGUE OUTPUTS (RCA, variable/fixed level) - To connect to a preamplifier (or power amplifier when internal volume control is enabled) with unbalanced (RCA) analogue inputs.
  5. ANALOGUE INPUTS (RCA, line level) - To connect sources with unbalanced (RCA) analogue outputs.
  6. RC5 ACCESSORY - To connect to a Linn BASIK3 or BASIK3-IR Knekt control device, (setup for RoomAmp2 connection (jumper link removed)). This requires a Knekt-CAT-5 cable to connect to the Linn DS
  7. IR OUTPUTS - To connect to infrared flasher devices allowing control of other products that accept infra-red signals.
  8. RS232 PORTS - To connect to other Linn devices that don't have ethernet.
  9. ETHERNET - To connect to a network.
  10. DIGITAL INPUT (Spdif) - To connect sources with Spdif (RCA) digital outputs.
  11. DIGITAL INPUT (Toslink) - To connect sources with Toslink (optical) digital outputs.


Front Panel Connections

Image:Sekrit_DSI_front.jpg


  1. POWER SWITCH - Switches the power on/off
  2. FALLBACK BUTTON - To put the device into Fallback mode (used when reprogramming)


LED FUNCTIONS

Text

ON

indicates

OFF

indicates

Slow Flash / Blink

Fast Flash

STANDBY Device in standby Device active Searching for IP address (boot) Fallback (reprogramme)
LINK Ethernet link established no link established n/a n/a
DHCP DHCP IP address obtained Default IP address obtained n/a n/a
AUDIO Valid audio (digital inputs only) n/a Invalid audio (digital inputs only) n/a
POWER AMP Internal amplifier enabled Internal amplifier disabled Internal amplifier fault n/a
RCU Reserved for future use Reserved for future use Reserved for future use n/a
SEARCH n/a n/a Find me n/a
TRANSMIT Reserved for future use n/a n/a n/a


Installation

Please read the following carefully before installing the unit in your system – your unit may need to be reconfigured by your Linn retailer.


For further assistance, try our customer support pages or the Linn Forum.