Difference between revisions of "Klimax DSM (Exakt Variant)"

From LinnDocs
Jump to: navigation, search
(Back Panel Connections)
Line 8: Line 8:
 
* ''Product Name:'' Klimax DSM/1
 
* ''Product Name:'' Klimax DSM/1
  
* ''Date of Introduction:''June 2014
+
* ''Date of Introduction:''June 2014 - Sept 2016
 
* ''Type:'' Integrated digital music player and preamplifier
 
* ''Type:'' Integrated digital music player and preamplifier
 
* [http://small.linncdn.com/product-catalogue/documents/Linn_Klimax_DSM_Product_Information.pdf Product Information sheet]
 
* [http://small.linncdn.com/product-catalogue/documents/Linn_Klimax_DSM_Product_Information.pdf Product Information sheet]

Revision as of 13:48, 8 November 2016

KlimaDS 3Q 02 low res.jpg

Getting Started

www.linn.co.uk/go/klimax

Product info

  • Product Name: Klimax DSM/1

Support

Linn Support Site

Latest software

Latest software releases

Open source software

Manuals

Quickstart Guide

Konfig manual

Space Optimisation+

Space Optimisation (Advanced)

Kinsky Desktop manual

DSM Remote control manual

Kinsky Jukebox manual

Safety Information

Warranty Terms & Conditions

Product information

HDMI Setup

HDMI Setup

DSM Audio Latencies Explained

Network Setup

DS Budget System Setup

DS Entry Level System Setup

DS High End System Setup

Back Panel Connections

Image:Kli DSM 1 rear.jpg


  1. MAINS INPUT - To connect to the mains electricity supply.
  2. TOSLINK IN- To connect sources with Toslink (optical) digital outputs.
  3. ETHERNET - To connect to a network.
  4. SPDIF IN - To connect sources with Spdif digital outputs.
  5. EXAKT LINK- To connect to Exakt compatible devices
  6. EARTH GROUND - For connecting the unit to an earthing terminal if no mains earth is available or for joining the earths of other products in the system to improve perfromance in areas of poor/noisy electrical earth conditions.
  7. BALANCED IN RIGHT, LEFT - To connect sources with balanced (XLR) outputs. 1 2
  8. BALANCED OUT RIGHT, LEFT - To connect to a preamplifier (or power amplifier when internal volume control is enabled) with balanced (XLR) analogue inputs.2
  9. UNBALANCED OUT RIGHT, LEFT - To connect to a preamplifier (or power amplifier when internal volume control is enabled) with unbalanced (RCA) analogue inputs.2
  10. HDMI OUT - To connect to a display device with HDMI inputs.
  11. HDMI IN 1, 2, 3 - To connect sources with HDMI outputs.
  12. FALLBACK - To put the device into Fallback mode (used when reprogramming the unit).



1 XLR to RCA adaptors are supplied for connecting sources with unbalanced outputs. Input transformer can be enabled or disabled in Konfig setup

2 Set to DELAY mode > DIRECT to pass through an Analogue volume control to the Analogue out.
Only use the XLR(8) output OR the RCA(9) output, never use both outputs as the RCA will degrade the XLR(8) output audio.

EXAKT LINK connection

Check HERE for information of Exakt link connection


Kli DSM 1 rear differences.jpg


Klimax DSM/1 differences


Changes to Klimax DSM/1 compared to the Klimax DSM/0

  1. - 2off Exakt link sockets - To connect speakers/Tuneboxes with Exakt Link. This will allow audio from both the Analogue output and Exakt outputs.
  2. - 1off SPDIF input - The Klimax DSM/0 has 2off SPDIF inputs



Front Panel

Image:Klimax_DSM_front.jpg


  1. DISPLAY
  2. ON / OFF SWITCH


Installation

Please read the following carefully before installing the unit in your system – your unit may need to be reconfigured by your Linn retailer.

For further assistance, try our customer support pages or the Linn Forum.

Exakt Options

Exakt usage the the Exakt Klimax speakers can be found at Klimax Exakt System


Trouble shooting

Check Exakt trouble shooting