HDMI

From LinnDocs
Revision as of 07:07, 18 April 2019 by Yoda (talk | contribs) (ARC - Audio Return Channel)
Jump to: navigation, search

The Linn DSM products provide HDMI pass through of HDMI V1.4 & V2.0 signals depending on the model

The Linn DSM products HDMI output will:-
1. Pass-throu the HDMI audio when the Linn DSM is in Standby.
2. Pass-throu the HDMI audio when the Linn DSM is listening to an Analogue or Digital Audio input.
3. BLOCK the HDMI audio to the TV if the the DSM is listening to a HDMI input.

ARC - Audio Return Channel

Due to difference in Manufacturers implementation of ARC, the Linn DSM does not support this function on Linn HDMI1 boards.

This is implemented in Klimax DSM, Akurate DSM and Majik DSM products from Sept 2016. Also available as an upgrade on earlier Klimax DSM, Akurate DSM and Majik DSM products

ARC will only feed SPDIF audio, that is Stereo and Dolby Digital/DTS. The Klimax DSM, Akurate DSM and Majik DSM will only support Stereo playback from this connection.

ARC setting on your Television vary from manufacturer to manufacturer. So please double check your TV setup manual.

Common issues for the lack of ARC audio:

1. The standard Linn DSM can only playback stereo audio. If the TV is set to output Dolby Digital or other Surround format then the Linn DSM will not play this audio and stay silent.
> Make sure the audio output is set to "STEREO"'
> If you are using an built-in service to the TV, such as Netflix, Amazon Prime etc, that you control from the TV handset then try a standard aerial TV channel or an external Satellite receiver and find out if you get any audio back from these TV sources.

2. The TV audio setup may be conflicting with itself.
> If possible do an "AV RESET" or equivalent on your TV, then setup for Audio format - Stereo and CEC-enabled (CEC can go by different names AnyNet+, Veiralink, SimpLink, Sony Bravia Sync,RIHD, Kuro Link..... etc. Check what your TV call it)

> In the worst case the simplest solution is to do a FACTORY DEFAULT/RESET on the TV. There may be a conflicting hidden setting that is causing all these issues, a Factory default will clear this and allow a fresh connection.
3. You are connected to the wrong socket on your TV.
> Check the Linn DSM HDMI output is connected to the TV socket that states "ARC"

4. Sony TV's and SKY-Q: It has been reported that this configuration can cause lack of ARC audio. When it does work,sometimes there is a crack/bang noise from the speaker when the system is put to Sleep/Standby.
> The solution is to disable HDMI control on the SKY-Q box and power cycle all of the products. (This is primarily an issue between Sky-Q and Sony Tv's communications)
5 Playstation5 (PS5): This can confuse the TV and what it is controlling the volume of, (the Linn DSM or PS5).
> The solution is In the PS5 setting go into HDMI > Enable HDMI Device Link > Off .


Common issues for the lack of ARC audio periodically muting:

1. Due to the introduction of eARC, some TV have this implements in different ways. The solution is:
> if your Linn DSM has the "eARC Mode" option in then turn this OFF
> If your TV has the option to disable the eARC functionality, then also turn this OFF

Can I only feed Audio via an HDMI connection to the Linn DSM?

This is totally dependant on the HDMI source.
The Linn DSM will totally ignore the video section of the HDMI link and only capture the audio section.
Some HDMI sources, such as the original Chromecast devices, would only output the Audio if a video playback device was found in the HDMI communication (EDID). Others do not care if there is a video playback device and will still forward the audio to the Linn DSM

I cannot get any picture through the HDMI

Playstation3

The Playstation3 is known to have HDMI connection issues with many non-Linn devices.

  1. Select PS3 input on the Linn DSM
  2. While the PLAYSTATION 3 system is in standby mode (red light on the front of the system), hold down the touch-sensitive power button on the front of the system until the system goes into standby mode again . (So the light cycle would go from: red light --> green light --> then back to red light). This will ensure that you have held down the power button long enough to reset the Video Output Settings.

Check PS3 FAQ's

Apple MacMini, MacBook Pro etc

If you switch the DSM to the HDMI feed from a MacMini, MacBook etc, it will initially loose any picture and audio, this may take up to 30seconds to appear and for the Audio to return. This delay is due to the Mac performing HDMI communication and re-establishing the audio and video options.

HDMI connection with Video scalers

If you have a video scaler in the HDMI chain and you are not getting any picture through the Linn DSM, take the video scaler out of the system to see if the picture returns.

No Audio playback on HDMI connection

The Linn DSM will ONLY support 2ch (or multichannel) PCM audio, it does not support Dolby Digital, DTS etc without a Linn Surround module. If you feed an unsupported audio from your DVD player/Sat Receiver etc the Linn DSM can pass though to the TV if the DS is in Standby mode but when you select that input on the DSM there is no audio then double check that the audio out on the DVD/Sat is configured for 2ch PCM.

Back


HDMI 2.0

Click <HERE> for information on HDMI 2.0 and Linn DSM products.