Difference between revisions of "Sekrit DS-I"
m (→Product info) |
m (→Installation) |
||
| Line 158: | Line 158: | ||
Please read the following carefully '''before''' installing the unit in your system – your unit may need to be reconfigured by your Linn retailer. | Please read the following carefully '''before''' installing the unit in your system – your unit may need to be reconfigured by your Linn retailer. | ||
| − | |||
| − | * [ | + | * [[product_unpacking|Unpacking Information]] |
| − | * [ | + | * [[product_positioning|Positioning Information]] |
| + | |||
| + | * [[amplifier_protection|Amplifier Protection]] | ||
| + | |||
| + | |||
| + | |||
| + | == '''FAQ's''' == | ||
| + | Check: | ||
| + | :* [[FAQ-Linn DS/DSM|'''<u>FAQ-Linn DS/DSM</u>''']] | ||
For further assistance, try our [http://www.linn.co.uk/linn_customer_support customer support] pages | For further assistance, try our [http://www.linn.co.uk/linn_customer_support customer support] pages | ||
Revision as of 14:38, 23 November 2018
Contents
Product info
- Product Name: Sekrit DS-I (2009 Variant)
- Date of Introduction: October 2009
- Discontinued: 2013 - replaced by the Sekrit DSM
- Type: Digital music player
Support
Latest software
Manuals
Third Party Software Copyright
Network Setup
Back Panel Connections
- MAINS INPUT - To connect to the mains electricity supply.
- EARTH GROUND - To connect to an earthing terminal if no mains earth is available or to join to the earths of other products in the system to improve performance in areas of poor/noisy electrical earth conditions.
- SPEAKER OUTPUTS - To connect to loudspeakers.
- ANALOGUE OUTPUTS (RCA, variable/fixed level) - To connect to a preamplifier (or power amplifier when internal volume control is enabled) with unbalanced (RCA) analogue inputs.
- ANALOGUE INPUTS (RCA, line level) - To connect sources with unbalanced (RCA) analogue outputs.
- RC5 ACCESSORY - To connect to a Linn BASIK3 or BASIK3-IR Knekt control device, (setup for RoomAmp2 connection (jumper link removed)). This requires a Knekt-CAT-5 cable to connect to the Linn DS
- IR OUTPUTS - To connect to infrared flasher devices allowing control of other products that accept infra-red signals.
- RS232 PORTS - To connect to other Linn devices that don't have ethernet.
- ETHERNET - To connect to a network.
- DIGITAL INPUT (Spdif) - To connect sources with Spdif (RCA) digital outputs.
- DIGITAL INPUT (Toslink) - To connect sources with Toslink (optical) digital outputs.
Front Panel Connections
- POWER SWITCH - Switches the power on/off
- FALLBACK BUTTON - To put the device into Fallback mode (used when reprogramming)
LED FUNCTIONS
|
Text |
ON indicates |
OFF indicates |
Slow Flash / Blink |
Fast Flash |
| STANDBY | Device in standby | Device active | Searching for IP address (boot) | Fallback (reprogramme) |
| LINK | Ethernet link established | no link established | n/a | n/a |
| DHCP | DHCP IP address obtained | Default IP address obtained | n/a | n/a |
| AUDIO | Valid audio (digital inputs only) | n/a | Invalid audio (digital inputs only) | n/a |
| POWER AMP | Internal amplifier enabled | Internal amplifier disabled | Internal amplifier fault | n/a |
| RCU | Reserved for future use | Reserved for future use | Reserved for future use | n/a |
| SEARCH | n/a | n/a | Find me | n/a |
| TRANSMIT | Reserved for future use | n/a | n/a | n/a |
Installation
Please read the following carefully before installing the unit in your system – your unit may need to be reconfigured by your Linn retailer.
FAQ's
Check:
For further assistance, try our customer support pages
