ExaktBox Sub

Product info

• Product Name: ExaktBox Sub

• Date of Introduction: September 2015

• Type: Exakt Digital Crossover with DAC designed for use with subwoofers

Configurable for one or two subwoofers

Software upgradable to support more and more subwoofers

Connects to internal subwoofer power amplifiers

• Can only be used with Exakt-Link output products AND Exakt speakers/Exaktbox

• Features
  • Dynamik Power Supply
  • Exakt Technology

Support

Linn Support Site

Installation

As this is an Exaktbox the initial setup must be performed with a Local Area Network that has Internet access. Otherwise Konfig cannot set the speaker channel, Speaker profile and Space Optimisation of these products

Latest software

Latest software releases

Open source software

Manuals

Konfig manual

Space Optimisation+

Surround Sound

Safety Information

Warranty Terms and Conditions

Back Panel Connections

1. MAINS INPUT - To connect to the mains electricity supply.
2. EXAKT LINK- To connect to Exakt compatible devices (CAT-5 cables)
3. ANALOGUE OUTPUTS (XLR,variable level) - To connect to power amplifiers with balanced (XLR) analogue inputs. (300ohm Output impedance)
4. ANALOGUE OUTPUTS (RCA, variable level) - To connect to power amplifier with unbalanced (RCA) analogue inputs. (300ohm Output impedance)
5. FALLBACK - Primarily for Linn service use only, to put the device into Fallback mode (used when reprogramming the unit).

Note: Both XLR and RCA outputs are active simulatneously.

EXAKT LINK Connections

Example if you are using a Klimaxe DSM/1, Akudoriks and Exaktbox sub:

The Exakt-link cable can supply digital audio for multiple speakers.
Use Konfig > Exakt Setup pages to declare if Channel1 is left or right hand channel, Channel2 is left or right hand channel and the type/quantity of subwoofers to the Exaktbox sub

Check HERE for more information of Exakt link connection

EXAKT LED Status

LED	OFF	ON	Flash / Blink
0 Master Port - BLUE	No Link	Link Discovered	Link Activity
0 Master Port - RED	No Link	No MAINS POWER	N/A
1 Audio Clock	No Clock	Clock locked	Clock not locked
2 Slave Port	No Link	Link Enabled	Link Activity
3 Software Status	Not Configured	Running	Hardware Fault

Front panel LED

Blue LED	STATUS
OFF	No Power (Exaktbox OFF)
ON	Active (Exaktbox ON)
Slow flash	Discovering
Fast flash	Configuring
slow Dim/BRIGHT flash	Fallback mode
fast Dim/BRIGHT flash	Reflashing

Installation

Please read the following carefully before installing the unit in your system – your unit may need to be reconfigured by your Linn retailer.

• Unpacking Information

• Positioning Information

• The ExaktBox is shipped from Linn with no speaker setup and must be configured with Konfig software.

Operation

The Exaktbox Sub can only be used in conjunction with Exakt speakers or Exaktboxes with two channel audio
You cannot mix the Exaktbox-Sub with the left/right speakers being fed from the Linn DS/DSM analogue sockets. Konfig will allow you to set this up but no audio will fed to the ExaktBox-sub

If you try and connect up the Exaktbox sub with non-Exakt speakers, Konfig will enable Space Optimisation+ and only list the Exakt products, it will NOT list any passive speakers. This means that you cannot setup the room for Space optimisation as only the Exaktbox sub can be setup.

Setup the Exaktbox Sub in the same manner as an Akurate Exaktbox, select the Speaker (or sub-woofer in this case), enter the serial number and which channel to process -left, right or Mono. (If you are using two sub-woofers define one as left and one as right or both as mono. If you are only using one subwoofer select Mono)

Linn Subwoofers

• Sizmik (1025 & 1045), Majik 126, Akurate 226, Akurate 221, Klimax 345
  

• Connection: Connect left, right or both RCA outputs from the Exaktbox sub to the appropriate RCA inputs on the subwoofer.

• Set the subwoofer parameters as indicated below:

Parameter	Symbol	Value
Internal High Pass Frequency	U	1
Internal Low Pass Frequency	L	4
Bass Equalisation	b	0
Absolute Phase	P	0

• Define the location of the subwoofer in Space Optimisation+
• Finally you should adjust the output level of the subwoofer to provide the best integration with the main system

Parameter	Symbol	Value
Coarse Gain	G	User set (range 1 – 7)
Fine Gain	f	User set (range 0 – 4)

• Afekt
  

• Connection: Connect left, right or both RCA outputs from the Exaktbox sub to the appropriate RCA inputs on the subwoofer.

• Set the subwoofer parameters as indicated below:

Parameter	Symbol	Value
Phase	P	0
Internal Low Pass Frequency	L	4

• Define the location of the subwoofer in Space Optimisation+
• Finally you should adjust the output level of the subwoofer to provide the best integration with the main system

Parameter	Symbol	Value
Coarse Gain	G	User set (range 1 – 7)

• AV5150, Melodik

• Connection: Connect left, right or both RCA outputs from the Exaktbox sub to the appropriate RCA inputs on the subwoofer.
• Using the dip switches as described in the Owners manual

set the Subwoofer phase response to NORMAL (in) phase.

set the frequency response to 79 Hz

• Define the location of the subwoofer in Space Optimisation+
• Finally you should adjust the output level of the subwoofer, using the dip switches, to provide the best integration with the main system.

REL Acoustics subwoofers

• Gibraltar G2

• Connection: Connect an RCA cable from the Exaktbox sub to the LFE input.
• Set the subwoofer to true phase (0 degrees).

• Define the location of the subwoofer in Space Optimisation+
• Finally you should adjust the output level of the subwoofer using the LFE gain control to provide the best integration with the main system.

• S/5, S/3, S/2

For Exakt filter version 3 or below

• Connection: Connect an RCA cable from the Exaktbox sub to the low .1/LFE input.
• Set the subwoofer to true phase (0 degrees).

• Define the location of the subwoofer in Space Optimisation+
• Finally you should adjust the output level of the subwoofer using the .1/LFE gain control to provide the best integration with the main system.

For Exakt filter version 4 or above

• Connection: Connect left, right or both RCA outputs from the Exaktbox sub to the LOW LEVEL INPUT RCA inputs on the subwoofer.
• Set the subwoofer to true phase (0 degrees).
• Set the subwoofer crossover dial to maximum (120 Hz)

• Define the location of the subwoofer in Space Optimisation+
• Finally you should adjust the output level of the subwoofer using the HI/LOW LEVEL control to provide the best integration with the main system.

Bowers and Wilkins subwoofers

• DB1

• Connection: Connect the Exaktbox sub to the subwoofer using either XLR or RCA cables.
• Set the subwoofer polarity to true phase (Normal).
• Turn OFF the room EQ (out), or set the room EQ to flat.
• Set the input sensitivity to 0dB
• Turn OFF the low pass filter (none).

• Define the location of the subwoofer in Space Optimisation+
• Finally you should adjust the output level of the subwoofer using the LFE gain control to provide the best integration with the main system.

Exakt options

Exakt usage can be found in Klimax_Exakt_System

One of the beneifts of the Exakt system is that you can easily setup and optimise your listening environment. Simply download the latest version of Konfig (version 4.11.7 or higher) and follow the Space_Optimsation+ & Space Optimisation+ (Advanced)

Supported Subwoofers

Examples using one ExaktBox Sub

• Afekt (1off or 2off)
• Akurate 226 (1off or 2off)
• Akurate 221 (1off or 2off)
• AV5150 (1off or 2off)
• Klimax 345 (1off or 2off)
• Majik 126 (1off or 2off)
• Melodik (1off or 2off)
• Sizmik (1025 & 1045) (1off or 2off)

Non-Linn Subwoofers

Examples using one ExaktBox Sub

• B&W DB1
• REL Gibraltar G2, S2, S3 & S5

More non-Linn subwoofers will be added in the future. In the meantime, if you want to use another type of subwoofer, select the Linn Akurate 221 or 226 and put in serial number 1234567. This will select a generic subwoofer profile with settings that can be used with non-Linn Subwoofers

Trouble shooting

Check Exakt trouble shooting

For further assistance, try our customer support pages