Difference between revisions of "Sekrit DSM"

From LinnDocs
Jump to: navigation, search
(Back Panel Connections)
(Speaker Wiring)
Line 47: Line 47:
  
 
== '''Speaker Wiring''' ==
 
== '''Speaker Wiring''' ==
 +
The Sekrit DSM has 4 DAC channels and 4 Power Amplifiers.  These amplifoers can be configuraed in seingle ended mode or Bridged mode.  The Single Ended mode is best suited to bi-amping a pair of passive speakers or for driving multiple pairs of loadspeakers.  Bridged mode is best suited to driving a single pair of loudspeakers. 
 +
 +
[[Image:SekritDsmConfiguration.jpg|center|700px]]
 +
 +
The riring details are shown below:
  
 
[[Image:SekritDsmWiring.jpg|center|700px]]
 
[[Image:SekritDsmWiring.jpg|center|700px]]
 
<br>
 
<br>
 
* 30W/channel in single-ended mode
 
* 30W/channel in single-ended mode
* 50W/channel in bridhed mode
+
* 50W/channel in bridged mode
  
 
== '''Back Panel Connections''' ==
 
== '''Back Panel Connections''' ==

Revision as of 10:52, 10 December 2012

SekritDsm.png

Product info

  • Product Name: Sekrit DSM
  • Date of Introduction: December 2012
  • Type: Integrated digital music player, pre-amplifier, and power amplifier

Support

Linn Support Site

Latest software

Latest software releases

Open source software

Manuals

Konfig manual

Kinsky Desktop manual

DSM Remote control manual

Safety Information

Warranty Terms and Conditions

HDMI Setup

HDMI Setup

Network Setup

DS Budget System Setup

DS Entry Level System Setup

DS High End System Setup

Speaker Wiring

The Sekrit DSM has 4 DAC channels and 4 Power Amplifiers. These amplifoers can be configuraed in seingle ended mode or Bridged mode. The Single Ended mode is best suited to bi-amping a pair of passive speakers or for driving multiple pairs of loadspeakers. Bridged mode is best suited to driving a single pair of loudspeakers.

SekritDsmConfiguration.jpg

The riring details are shown below:

SekritDsmWiring.jpg


  • 30W/channel in single-ended mode
  • 50W/channel in bridged mode

Back Panel Connections

SekritDsmRear 2.jpg
  1. MAINS INPUT - To connect to the mains electricity supply.
  2. FALLBACK- To put the device into Fallback mode (used when reprogramming).
  3. ETHERNET - To connect to a network.
  4. HDMI OUTPUT - To connect to a display device with HDMI inputs.
  5. HDMI INPUTS - To connect sources with HDMI outputs.
  6. ANALOGUE OUTPUT (RCA, variable/fixed level) - To connect to subwoofer or external power amplifier.
  7. IR OUTPUTS - To connect to infrared flasher devices allowing control of other products that accept infra-red signals.
  8. DIGITAL INPUT (Toslink) - To connect sources with Toslink (optical) digital outputs.
  9. DIGITAL INPUT (Spdif) - To connect sources with Spdif (RCA) digital outputs.
  10. ANALOGUE INPUT (line level) - To connect a turntable or line level source with unbalanced (RCA) outputs.
  11. SPEAKER OUTPUTS - To connect to loudspeakers
  12. ANALOGUE OUTPUT (RCA, variable/fixed level) - To connect to a preamplifier (or power amplifier when internal volume control is enabled) with unbalanced (RCA) analogue inputs.
  13. RC5 ACCESSORY - To connect BASIK-3 & BASIK-3IR Room Control units.


Front Panel Connections

SekritDsmFront 2.jpg
  1. IR SENSOR - Recieves IR commands
  2. DIAGNOSTIC LEDS - See table below for functionality
  3. FALLBACK (F-BACK) - To put the device into Fallback mode (used when reprogramming).
  4. POWER SWITCH- Switches the power on/off


DIAGNOSTIC LED FUNCTIONS

Text

ON

indicates

OFF

indicates

Slow Flash / Blink

Fast Flash

IR Pulse on IR command received Reserved for future use Reserved for future use n/a
P-AMP Internal amplifier enabled Internal amplifier disabled Internal amplifier fault n/a
AUDIO Valid audio (digital inputs only) n/a Invalid audio (digital inputs only) n/a
DHCP DHCP IP address obtained Default IP address obtained n/a n/a
LINK Ethernet link established no link established n/a n/a
STBY Device in standby Device active Searching for IP address (boot) Fallback (reprogramme)

*NOTE: All LED's will flash if 'Locate Device' request is invoked from Konfig


Installation

Please read the following carefully before installing the unit in your system – your unit may need to be reconfigured by your Linn retailer.


For further assistance, try our customer support pages or the Linn Forum.