Difference between revisions of "Exakt Optimsation"

From LinnDocs
Jump to: navigation, search
(Stage 4: Optimise for High Frequency Response)
(Stage 5: Fine Tune Filter Parameters to Improve Audio Performance)
Line 106: Line 106:
 
:      Click Show in graph, will show the bass frequency response in RED
 
:      Click Show in graph, will show the bass frequency response in RED
  
== Stage 5: Fine Tune Filter Parameters to Improve Audio Performance ==
+
== Stage 6: Fine Tune Filter Parameters to Improve Audio Performance ==
  
 
: 1. Select the '''Room Modes''' optimisation tab
 
: 1. Select the '''Room Modes''' optimisation tab

Revision as of 09:06, 23 October 2014

Introduction

Exakt Optimisation provides a listener focused view of room optimisation. This means that Exakt compatible products give the listener an opportunity to greatly improve the listening experience by providing the Exakt products with information about the listening environment. The software inside the Exakt products can then account for the listening environment and compenstate accordingly.

Overview

Internet connection is required for Konfig when using Exakt Systems

Konfig can optimise for the following acoustic phenomena:

Room Modes

Every room is different, and can therefore be optimised to sound as good as possible. You will need to use the TuneDem method to find the ideal location for your speakers.

Speaker Placement

In practice, the ideal TuneDem location for your speakers is rarely the practical location as well. Not to worry, optimisation will allow the ideal Tune Dem sound to be applied wherever your speakers are located.

High Frequency Response

Each room responds to high frequency (a.k.a. treble) differently. An empty room with marble walls will respond much differntly to a room with plasterboard walls and lots of soft furnishings. This stage allows you to optimise according to the high frequency response of your room.

Optimisation Process

Stage 1: TuneDem

1. Using the TuneDem method, deterimine the ideal speaker location for your room
2. Select your Exakt device in Konfig
3. Click on the Exakt Optimisation tab

Exakt Tabs

Stage 2: Optimise for Room Modes

Room Modes Dimensions

1. Click on the Room Modes optimisation tab.
2. Click on Change Dimensions.
3. Enter values for Room Dimensions, Listening Position, and Ideal TuneDem Speaker Position
a. All dimensions must be measured in meters.
b. Speaker measurements should be made from the outside front corner.
4. Click Optimise.
N.B. To remove any Room Mode optimistaion from your setup click Disable .

RoomMeasurement


The Room Modes graph now displayed shows the audio notch filters/Room Modes that are applied to the audio stream before being played back from the speakers.
All of these filters are applied in unison, they are not individual filters that you select to be operation one at a time.

The Exakt "Room Modes"/Notch filters are used to correct room audio reflections from the wall, ceiling, floor and furnishings. These reflections can cause highs and lows in the frequency response, these Room Modes filters correct these distortions.

Each Room Mode/Notch filter can be adjusted manually, we advice that only the Gain values are changes. As an example, if you want tune in the Exakt settings, after Tune-dem placements:-

1. Select a Room Mode
2. Take a note of the Gain value of that Room mode
3. Adjust the value of this Room Mode Gain and listen to the difference
4. Repeat steps 2&3 until you get the best Tune from this Room Mode then go onto the next Room Mode.

There are many different procedures for finding the best Gain value. The simplest way is normally then half value. Take the difference between the Gain value and zero then half it. Listen to at centre gain plus half value and then minus half value to find the best Gain setting for the tune. Half the value between the two best sound gains and vary this by half again.

e.g.
Original value -20dB
Try Gains -20dB, -40dB & 0dB
If 0dB sounds better use values -10dB, -15dB, -5dB
if -5dB sounds better uses values -5dB, -7.5dB, -2.5dB
OR
if -15dB sounds better uses values -15dB, -17.5dB, -12.5dB
etc....

Stage 3: Optimise for Speaker Placement

Speaker Placement Dimensions

1. Click on the Speaker Placement optimisation tab.
2. Click on Change Placement.
3. Enter values for Practical Speaker Position
a. All dimensions must be measured in meters.
b. Speaker measurements should be made from the outside front corner.
c. Ideal TuneDem Speaker Position mesaurements will be pre-populated from Stage 2, no need to change them
4. Click Optimise.
N.B. To remove any Speaker Placement optimistaion from your setup click Disable.

RoomMeasurement

Stage 4: Optimise for High Frequency Response

High Frequency Response

1. Click on the Furnishing and Construction optimisation tab. Then treble shelf
2. Enter frequency and gain values as required.
N.B. To disable any high frequency response set the gain to 0.


Stage 5: Optimise for bass response

Bass Response

1. Click on the Furnishing and Construction optimisation tab. This stage is the equivalent of a treble shelf.
2. Enter frequency and gain values as required.
Typical value range -6dB > + 3dB, 20Hz-200Hz
N.B. To disable any bass response set the gain to 0.
Click Show in graph, will show the bass frequency response in RED

Stage 6: Fine Tune Filter Parameters to Improve Audio Performance

1. Select the Room Modes optimisation tab
2. Each notch filter in the room optimisation graph is represented by a Room Mode (i.e. Room Mode 1, Room Mode 2, etc).
3. You can modify a notch filter by selecting it from the drop down box and entering new values.
4. Room mode optimisation is based on an idealised rectangular room, so some modifications to these values may be required
5. Speaker Placement optimisation is less prone to error, so modifying these values is not recommended

RoomMeasurement

  • Changing the Frequency value will shift the notch filter left or right along the x-axis.
  • Changing the Gain value will change the height of the notch filter.
  • Changing the Bandwidth value with change the width of the notch filter.

Known Restrictions

Room optimisation graphs will not be visible if you are running Konfig on Windows XP. This is because Konfig requires IE9 or higher and Windows XP is not compatible with IE9 or higher.