Akurate ExaktBox

From LinnDocs
Revision as of 07:34, 25 February 2016 by Yoda (talk | contribs) (Supported speakers)
Jump to: navigation, search
AkurateExaktBoxFront.jpg

Getting Started

www.linn.co.uk/go/akurate

Product info

  • Product Name:
Akurate ExaktBox (10-channel)
Akurate ExaktBox ( 6-channel)
  • Date of Introduction:
September 2014 (10-channel)
September 2015 ( 6-channel)
  • Type: Digital Crossover with Exakt Technology
Supports
Stereo speakers from 2way to 3way (6-channel) or 5-way (10-channel)
Mono speakers from 2way to 6way (6 & 10 channel)
Software upgradable to support more and more loudspeakers
Connects to power amplifiers and externally Aktiv speakers
  • Can only be used wit Exakt-Link output products

Support

Linn Support Site

Installation


As this is an Exaktbox the initial setup must be performed with a Local Area Network that has Internet access. Otherwise Konfig cannot set the speaker channel, Speaker profile and Space Optimisation of these products


Latest software

Latest software releases

Open source software

Manuals

Konfig manual

Space Optimisation+

Space Optimisation (Advanced)

Safety Information

Warranty Terms and Conditions

Back Panel Connections

Ak ExaktBox BP-Nums.jpg
Ak Exaktbox6+BP nums.jpg



  1. MAINS INPUT - To connect to the mains electricity supply.
  2. EXAKT LINK- To connect to Exakt compatible devices (CAT-5 cables)
  3. ANALOGUE OUTPUTS (XLR,variable level) - To connect to power amplifiers with balanced (XLR) analogue inputs. (300ohm Output impedance)
  4. ANALOGUE OUTPUTS (RCA, variable level) - To connect to power amplifier with unbalanced (RCA) analogue inputs. (300ohm Output impedance)
  5. FALLBACK - Primarily for Linn service use only, to put the device into Fallback mode (used when reprogramming the unit).

Note: Both XLR and RCA outputs are active simulatneously.

EXAKT LINK Connections

Image:Exakt Link.jpg


Example if you are using a Akurate DSM/1 to connect to an Akurate ExaktBox:

AkDSM to AkExaktBox wiring.jpg


The Exakt-link cable can supply digital audio for multiple speakers.
Use Konfig > Exakt Setup pages to declare if Channel1 is left or right hand channel and Channel2 is left or right hand channel

Check HERE for more information of Exakt link connection



Power Amplifier/Speaker connections

DOUBLE CHECK the wiring from the Exaktbox to power amplifier to speaker terminals!
If there are any mis-wires or wrong speaker definintions in the Exaktbox, you may blow the speaker drive units, so take care.

If this is the first connection use the standard Aktiv test scenario.

  1. Switch off ALL power amplifiers.
  2. Disconnect any power amplifier to speakers connections
  3. Set to a low volume value, e.g 40-50
  4. Do the following tests 5,6,7,8 starting with the Bass connections, then Midrange, then tweeter and finally super tweeter in that order.
  5. Connect respective (Bass or Mid or tweeter ot super-tweeter) power amplifier connection to the Bass connection (Bass or Mid or tweeter ot super-tweeter) of the speaker.
  6. Switch on the respective amplifier and play some Music. Check that you are only getting (Bass or Mid or tweeter ot super-tweeter) audio from that speaker drive unit.
  7. Stop the Music playing.
  8. Leave this cable connected go to Step4 and connect the next speaker drive unit in the list.

If you change speaker or variant, this may also change the Exaktbox terminations so DOUBLE CHECK

To see the Exaktbox terminations for each speaker click here




EXAKT LED Status

Image:Akurate ExaktBox


LED

OFF

ON

Flash / Blink

0 Master Port No Link Link Discovered Link Activity
1 Audio Clock No Clock Clock locked Clock not locked
2 Slave Port No Link Link Enabled Link Activity
3 Software Status Not Configured Running Hardware Fault













Installation

Please read the following carefully before installing the unit in your system – your unit may need to be reconfigured by your Linn retailer.

  • The ExaktBox is shipped from Linn with no speaker setup and must be configured with Konfig software.

Exakt options

Exakt usage can be found in Klimax_Exakt_System

One of the beneifts of the Exakt system is that you can easily setup and optimise your listening environment. Simply download the latest version of Konfig (version 4.11.7 or higher) and follow the Space_Optimsation+ & Space Optimisation+ (Advanced)



Supported speakers

Connection Help.jpg

Select CONNECTION HELP for up to date wiring information


Currently available using one Akurate Exaktbox
Note: these speakers must be made externally Aktiv

Standard production mid-range 007 & tweeter 015
Mid-range 081 & tweeter 038 were used for repair or upgrade
Standard production tweeter 015, Tweeter 038 were used for repair or upgrade





non-Linn speakers

Currently available

  1. B&W Nautilus
  2. B&W 802 Diamond
  3. KUDOS Super10
  4. KUDOS Super20
  5. KUDOS Titan 808



Example of use

Akurate Exakt example.jpg

Trouble shooting

Check Exakt trouble shooting

For further assistance, try our customer support pages or the Linn Forum.