Difference between revisions of "Akubarik Exakt"

From LinnDocs
Jump to: navigation, search
m
m (History of upgrade options)
Line 21: Line 21:
 
==<b>History of upgrade options</b>==
 
==<b>History of upgrade options</b>==
 
{{Info:Upgrade_HIstory_statement}}
 
{{Info:Upgrade_HIstory_statement}}
:* [[File:Organik_Logo_Black.png |link=Organik_DAC|80px]]: Organik DAC upgrade for Akubarik (March 2024)
+
:* [[File:Organik_Logo_Black.png |link=Organik_DAC|80px]]: <b>Organik DAC upgrade for Akubarik Exakt</b> (March 2024)
 
:::This requires the Akubarik modules to be returned to the Linn factory, via the Linn Retailer, for this upgrade.
 
:::This requires the Akubarik modules to be returned to the Linn factory, via the Linn Retailer, for this upgrade.
  

Revision as of 12:25, 3 April 2024

Akubarik Wal 3Q.jpg


Product info

  • Product Name: EXAKT AKUBARIK
  • Date of Introduction:
April 2014
September 2017 - updated to Katalyst
  • Type: Fully Integrated Aktiv Isobarik Loudspeaker with Exakt Technology


History of upgrade options

This list is only a summary of upgrades that are/were available for this product.
Please check with your Retailer to verify if these upgrades are still available.

  • Organik Logo Black.png: Organik DAC upgrade for Akubarik Exakt (March 2024)
This requires the Akubarik modules to be returned to the Linn factory, via the Linn Retailer, for this upgrade.

Manuals

Quickstart

Safety Information

Warranty Terms & Conditions

Linn Support Site

Tech Spec

Installation

We recommend that your Akubarik loudspeakers are unpacked, installed and adjusted by an authorised Linn retailer. To get the best from your Akubarik loudspeakers, it is important that they are positioned and levelled correctly.

Please note, in order to achieve the very best from your Akubarik, some adjustment may be required after positioning, levelling and connecting. See the Fine adjustment section.
As this is an Exakt speaker the initial setup must be performed with a Local Area Network that has Internet access. Otherwise Konfig cannot set the speaker channel, Speaker profile and Space Optimisation of these products

Unpacking

Image:Akubarik_no_lie.jpg

IMPORTANT: The Akubariks are heavy; take great care when moving them.
When unpacking, lifting or moving them, we recommend using two people to avoid personal injury.


  • Do not lift your Akubarik using the amplifier module, this will cause damage to your loudspeaker.
  • Do not lay the loudspeakers on their front face or the amplifier on the rear as this will damage the loudspeaker.
  • We recommend that you retain the packaging in case you need to transport your loudspeaker(s) at a later date.
  • Loudspeakers are packed individually with a separate package containing both speaker stands.
  • Take care when unpacking to avoid damage to the cabinets.


Move the (boxed) loudspeaker to an uncluttered, flat area adjacent to its eventual position (this will avoid any excessive moving and carrying of unpacked loudspeakers).

Stand the loudspeaker box on its base.

Remove the plastic clips holding the box together (four from the base and one from the sleeve).

Remove the cardboard sleeve by lifting it straight up until it clears the top of the cabinet

Leaving the top end cap on (to protect the loudspeaker) turn the Akubarik upside down.

Remove the bottom end caps to allow the stand to be fitted (see below).

Once the stand has been fitted, carefully rotate speaker onto the stand. Lift the loudspeaker out of the top end-cap and remove its protective bag.

Leave the packaging between the amplifier module and the cabinet and the 3-K Array cover in place until the loudspeakers have been moved to their final position.

Once you have positioned the loudspeakers, remove the two packaging pieces between the amplifier and the cabinet and VERY CAREFULLY snip the plastic tie holding the 3-K Array cover in place and remove it.


Fitting the Stand


Image:Stand fitting.jpg


On a clean, level surface that will not damage the loudspeaker; carefully stand the speaker upside-down without laying it on its front or rear face.

Remove the five bolts holding the transit plinth in place using a 13mm socket spanner.

Remove the transit plinth and retain with the packaging in case you need to transport your loudspeaker(s) in the future.

Position the speaker stand above the speaker as shown above and attach using the 5 bolts removed earlier.

IMPORTANT: Take care not to over tighten the bolts.


Positioning

As with any stereo loudspeaker there are some fundamental principles which should be observed to get the best sound from your loudspeakers.

  • The loudspeakers should be place at an equal distance from the wall behind the loudspeakers.
  • The speakers should be a similar (not the same) distance from the walls to the outside of each loudspeaker.
  • Any toe-in applied should be the same for each loudspeaker.
  • The loudspeakers should be level with all four spikes in contact with the floor. Use Linn Skeets for hard floors.

As the Akubarik loudspeaker has a ported bass system the low frequency performance will be better if the loudspeakers are pulled out from the wall, 20-30cm is a good starting point, but adjustment will be required to get the best results. Additional benefit will be heard in the upper midrange and high frequencies by placing the loudspeakers away from the rear wall.

The Linn 3K Array used in the Akubarik loudspeaker offers exceptional dispersion characteristics. This means that there should be little or no need to toe-in your loudspeakers.


For further assistance, try our customer support pages

Levelling

Image:Akubarik_insert_spike.jpg


Screw the spikes into the corners of the stand.
Fit the lock nuts but do not tighten at this stage.







Image:Akubarik_adjust_spikes.jpg


Very carefully (do not scratch the cabinet), use a spirit level to check if it is sitting level. If it is, gently rock the loudspeaker from front to back, side to side and diagonally to check for any movement. If none is present and the loudspeaker is sitting level, no adjustment to the spikes is necessary.


If the loudspeaker is not level, or moves when you rock it, loosen the appropriate lock nuts using the tool provided and use a screwdriver to turn the spikes to adjust their height. Adjust the spikes to level the speaker, using a spirit level placed on the stand.

Press down firmly on the top of the loudspeaker to ensure it is in close contact with your flooring.

Use the spirit level as before and continue to adjust the spikes as required.



Image:Akubarik_adjust.jpg

Once the speaker is level and does not rock, use the screwdriver to hold the spike in place and fit and tighten the lock nuts with the spanner provided.


Note: To protect wooden or tiled floors, the spikes can be placed on Linn Skeets which are available from your Linn retailer.


Connections

Lower Back Panel

Image:Akubarik Exakt


  1. MAINS INPUT - To connect to the mains electricity supply.
  2. EXAKT LINK - From Exakt Master OR from a Exakt Slave connected to the Exakt master
  3. EXAKT LINK - To Exakt Slave product

Akurate_Exakt_System has more detail on connection and usage

EXAKT LINK connection

Check HERE for information of Exakt link connection









Upper Back Panel

Image:Akubarik Exakt


5 FALLBACK - Primarily for Linn service use only, to put the device into Fallback mode (used when reprogramming the unit).
6 SPEAKER STATUS INDICATORS - Combined RED/Blue LEDs showing the speaker function. See below:







Operation

Image:Akubarik_Exakt_OFF_V2.jpg

General

If the Exakt DSM is in Standby, the Akubarik speaker is totally shutdown. No LED's or indicators are shown




Image:AkubarikE_ON_V2.jpg

When the Exakt DSM is brought out of Standby it will send trigger voltage and wake the speaker up. The LED's beside the Mains socket/Exakt link sockets will tell you the status. After approx 6seconds the Blue LED on the top of the speaker will illuminate stating "its ready to party!"




Image:No_Power.jpg‎

If you have brought the Exakt DSM out of standby and you only get this LED then the speaker has no Mains power. Check the Mains lead is fully inserted into the speaker and the wall socket mains switch is ON.




EXAKT STATUS INDICATORS

Image:Akubarik Exakt


EXAKT LED Status

LED

OFF

ON

Flash / Blink

0 Master Port No Link Link Discovered Link Activity
1 Audio Clock No Clock Clock locked Clock not locked
2 Slave Port No Link Link Enabled Link Activity
3 Software Status Not Configured Running Hardware Fault















Upper Back Panel

Image:AkuBarik Exakt Top-LED_V2


Speaker status LED

RED LED

BLUE LED

STATUS


OFF OFF No Power (Speaker OFF)
OFF ON Active (Speaker ON)
ON OFF Standby (Not implemented)
ON ON Invalid state
OFF Slow flash Discovering
OFF Fast flash Configuring
Fast flash OFF Hardware fault
Slow Alternating flash Slow Alternating flash Fallback mode
Fast Alternating flash Fast Alternating flash Reflashing